Table of Contents
Advertisement
11.4 Setting added steam
Requirements
¡ Observe the information about the respective operat-
ing mode.
→ "Setting options with steam", Page 17
¡ The water tank has been filled. If the water tank runs
dry during operation, a message appears on the dis-
play. The appliance continues to operate but without
injecting steam into the cooking compartment.
→ "Filling the water tank", Page 17
Press the operating mode that you require in the
1.
menu.
Select the settings for the operating mode, e.g. type
2.
of heating and temperature.
Press
"Added steam".
3.
Use the setting ring to set the steam level.
4.
Steam level
1
2
3
To confirm the set steam level, press
5.
play.
Press
to start the operation.
6.
a The appliance starts heating.
a The setting values and how long the appliance has
already been in operation are shown on the display.
When the food is ready, use
7.
ance off.
Empty the water tank and dry the cooking compart-
8.
ment.
→ "After using steam operation", Page 19
Changing added steam
You can change or deactivate the added steam func-
tion at any time.
Press
on the display.
1.
Press added steam
2.
Change or deactivate added steam using the setting
3.
ring.
To confirm the change, press
4.
a The change is applied.
11.5 Setting the steam jet function
Requirements
¡ Observe the information about the respective operat-
ing mode.
→ "Setting options with steam", Page 17
¡ The water tank has been filled. If the water tank runs
dry during operation, a message appears on the dis-
play. Operation is stopped.
→ "Filling the water tank", Page 17
Press the operating mode that you require in the
1.
menu.
Select the settings for the operating mode, e.g. type
2.
of heating and temperature.
Press
to start the operation.
3.
Press
on the display at the desired time.
4.
Do not use the steam jet until the appliance has
completely heated up.
Press
"Steam jet".
5.
a The
symbol lights up red and the appliance heats
up the water.
Added steam
Low
Medium
High
on the dis-
to switch the appli-
.
on the display.
When the water is heated up, press
6.
again.
Note: If rapid heating
can only be triggered once rapid heating is com-
plete.
a The steam jet is triggered and the appliance adds
clouds of steam to the cooking compartment for ap-
prox. 3 to 5 minutes.
a When the steam jet has finished, the operation con-
tinues to run as normal. Depending on the opera-
tion, the steam jet can be triggered again if neces-
sary.
When the food is ready, use
7.
ance off.
Empty the water tank and dry the cooking compart-
8.
ment.
→ "After using steam operation", Page 19
Cancelling the steam jet
You can cancel the steam jet at any time.
Press
on the display.
1.
Press
" Steam jet".
2.
a The
symbol changes back to white.
a The operation continues without the steam jet.
11.6 After using steam operation
Dry the appliance after each steam operation.
Note: Traces of limescale may remain in the cooking
compartment after operation with steam. The functional-
ity of the appliance is not affected by this. You can re-
move traces of limescale using hot water or a cloth
soaked in vinegar. Observe the information on clean-
ing.
→ "Cleaning and servicing", Page 28
Emptying the water tank
WARNING ‒ Risk of burns!
The water tank may heat up while the appliance is in
operation.
Wait until the water tank has cooled down from the
▶
previous operation.
Remove the water tank from the tank recess.
▶
ATTENTION!
Drying the water tank in the hot cooking compartment
leads to damage to the water tank.
Do not dry the water tank in the hot cooking com-
▶
partment.
Cleaning the water tank in the dishwasher will damage
it.
Do not clean the water tank in the dishwasher.
▶
Clean the water tank with a soft cloth and standard
▶
washing-up liquid.
Use
to open the control panel.
1.
Remove the water tank.
2.
Carefully remove the lid of the water tank.
3.
Empty the water tank, clean it with detergent and
4.
then rinse it thoroughly with clean water.
5.
Dry all parts with a soft cloth.
Rub the seal on the lid until dry.
6.
Leave the water tank to dry with the lid open.
7.
8.
Place the lid on the water tank and push down on it.
Insert the water tank and close the control panel.
9.
Steam en
"Steam jet"
is activated, the steam jet
to switch the appli-
19
Advertisement
Table of Contents
