Table of Contents
Advertisement
Quick Links
INSTALLATION AND MAINTENANCE INSTRUCTIONS
[ Model ] Floor standing
Applicable models
AXLP22P2D
AXLP28P2D
AXLP36P2D
Important reminder
- THOROUGHLY READ THESE INSTRUCTIONS BEFORE STARTING THE INSTALLATION AND FOLLOW
ALL PROCEDURES DESCRIBED WITHIN.
- KEEP THIS MANUAL IN A HANDY PLACE FOR FUTURE REFERENCE.
After installation, always use the checklist to perform a final inspection.
Always read before installation.
Aisin INDOOR UNITS
AXLP45P2D
AXLP56P2D
AXLP71P2D
AXLP22 -71P2D
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Aisin AXLP22P2D
Summary of Contents for Aisin AXLP22P2D
- Page 1 AXLP22 -71P2D Always read before installation. Aisin INDOOR UNITS INSTALLATION AND MAINTENANCE INSTRUCTIONS [ Model ] Floor standing Applicable models AXLP22P2D AXLP45P2D AXLP28P2D AXLP56P2D AXLP36P2D AXLP71P2D Important reminder - THOROUGHLY READ THESE INSTRUCTIONS BEFORE STARTING THE INSTALLATION AND FOLLOW ALL PROCEDURES DESCRIBED WITHIN.
- Page 2 Control box IN/D OUT/D Control box IN/D OUT/D Control box IN/D OUT/D Control box Control box IN/D OUT/D IN/D OUT/D...
- Page 3 d EK ^ ^ s/ D EKE/ > > /d >z y&W y&W y&W y&W y&W y&W y&W y&W yDW W yDW W yDW W yDW W y W W y W W y W W y W W y W W ...
-
Page 4: Table Of Contents
Installation and AXLP22~71P2D Gas driven heat pumps air conditioners operation manual Contents Before installation Page Before installation................1 Leave the unit inside its packaging until you reach the installation site. Where unpacking is unavoidable, use a sling of Important information regarding the refrigerant used ......2 soft material or protective plates together with a rope when Selecting installation site .............. -
Page 5: Important Information Regarding The Refrigerant Used
Accessories Important information regarding the refrigerant used Check if the following accessories are included with your unit. This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. Refrigerant type: R410A value: 1975 GWP = global warming potential Metal clamp Insulation for liquid pipe Periodical inspections for refrigerant leaks may be required Drain hose... - Page 6 Install the unit according to the figures below. Unit of measurement = mm For AXLP units only For FXNQ units only Model Front side 20+25 32+40 50+63 Air inlet direction Width of air inlet Air outlet direction Width of maintenance area 1030 1170 1450...
-
Page 7: Indoor Unit Installation
Indoor unit installation Wallmounted installation As for the parts to be used for installation work, be sure to use the Check whether the wall is strong enough to bear the provided accessories and specified parts designated by our weight of the unit. If there is a risk, reinforce the wall company. -
Page 8: Refrigerant Piping Work
Use copper alloy seamless pipes (ISO 1337). The outdoor unit is charged with refrigerant. To prevent water leakage, execute heat insulation work completely on both sides of the gas and liquid piping. When using a heat pump, the temperature of the gas piping can reach up to approximately 120°C. -
Page 9: Drain Piping Work
Cautions for brazing Drain piping work Be sure to carry out a nitrogen blow when brazing. Rig the drain pipe as shown below. Improperly rigged piping could Brazing without carrying out nitrogen replacement or releasing lead to leaks and eventually wet furniture and belongings. nitrogen into the piping will create large quantities of oxidized film on the inside of the pipes, adversely affecting valves and Carry out the drain piping... -
Page 10: Electric Wiring Work
Electric wiring work Precautions Observe the notes mentioned below when wiring to the power supply terminal board. General instructions Use a round crimp-style terminal for insulation sleeve for connection to the terminal block for wiring the units. When DANGER: ELECTRICAL SHOCK none are available, follow the instructions below. -
Page 11: How To Install The Remote Controller And Wiring Inside The Unit
Electrical characteristics Wiring installation Remove the control box cover and connect the wiring. Power supply Fan motor Voltage Model Volts range 0.015 0.015 0.025 50/60 220-240/220 ±10% 0.025 0.035 0.035 MCA: Minimum Circuit Amps (A) MFA: Maximum Fuse Amps (A) FLA: Full Load Amps (A) For details, refer to "Electrical data"... -
Page 12: Wiring Examples
Wiring examples Field setting Fit the power supply wiring of each unit with a switch and fuse as Field setting must be made on the remote controller in function of the shown in figure installation condition. Setting can be made by changing the "Mode number", "First Power supply BS unit (only for heat code No."... -
Page 13: Test Operation
Test operation How to clean the air filter Refer to the installation manual of the outdoor unit. Clean the air filter when the display shows " " (TIME TO CLEAN AIR FILTER). The operation lamp of the remote controller will flash when an error occurs. -
Page 14: Disposal Requirements
How to clean air outlet and outside panels Start up after a long stop Clean with soft cloth. Confirm the following: When it is difficult to remove stains, use water or neutral Check that the air inlet and outlet are not blocked. Remove any detergent. -
Page 15: Wiring Diagram
Wiring diagram : TERMINAL BLOCK : BLACK : PINK : CONNECTOR : BLUE : RED : TERMINAL : BROWN : WHITE : FIELD WIRING : ORANGE : YELLOW : PROTECTIVE EARTH (SCREW) : LIVE : NEUTRAL A1P....PRINTED CIRCUIT BOARD T1R....TRANSFORMER (220-240 V/22 V) C1 .... - Page 16 04.2014...
Need help?
Do you have a question about the AXLP22P2D and is the answer not in the manual?
Questions and answers