Table of Contents
Advertisement
Quick Links
INSTALLATION AND MAINTENANCE INSTRUCTIONS
[ Model ] High static pressure duct Type
Applicable models
AXMP45P7D
AXMP56P7D
AXMP71P7D
Important reminder
- THOROUGHLY READ THESE INSTRUCTIONS BEFORE STARTING THE INSTALLATION AND FOLLOW
ALL PROCEDURES DESCRIBED WITHIN.
- KEEP THIS MANUAL IN A HANDY PLACE FOR FUTURE REFERENCE.
After installation, always use the checklist to perform a final inspection.
Always read before installation.
Aisin INDOOR UNITS
AXMP90P7D
AXMP112P7D
AXMP140P7D
AXMP45 - 140P7D
Advertisement
Table of Contents
Related Manuals for Aisin AXMP90P7D
Summary of Contents for Aisin AXMP90P7D
- Page 1 AXMP45 - 140P7D Always read before installation. Aisin INDOOR UNITS INSTALLATION AND MAINTENANCE INSTRUCTIONS [ Model ] High static pressure duct Type Applicable models AXMP90P7D AXMP45P7D AXMP56P7D AXMP112P7D AXMP71P7D AXMP140P7D Important reminder - THOROUGHLY READ THESE INSTRUCTIONS BEFORE STARTING THE INSTALLATION AND FOLLOW ALL PROCEDURES DESCRIBED WITHIN.
- Page 2 ≥300 <45 ≤300 mm 1~1.5 m...
- Page 3 AXSP90P7D AXSP112P7D AXSP140P7D AXHP36AVD AXHP71AVD AXHP112AVD AXDP22P7D AXDP28P7D AISIN SEIKI CO.LTD Brand: Marca: See the number on the unit label Serial number: N° di serie: vedere il numero sulla targa dati Year of production: See the year on the unit label...
-
Page 4: Table Of Contents
Installation and AXMP45P7D AXMP90P7D AXMP224P7D Gas driven heat pumps air conditioners AXMP56P7D AXMP112P7D AXMP280P7D operation manual AXMP71P7D AXMP140P7D ONTENTS EFORE INSTALLATION Page Before installation................1 Leave the unit inside its packaging until you reach the installation site. Where unpacking is unavoidable, use a sling of Important information regarding the refrigerant used...... -
Page 5: Important Information Regarding The Refrigerant Used
Optional accessories ELECTING INSTALLATION SITE There are two types of remote controllers: wired and wireless. (See figure 1 figure Select a remote controller according to customer request and install in an appropriate place. Select an installation site where the following conditions are Refer to catalogues and technical literature for selecting a fulfilled and that meets your customer's approval. -
Page 6: Preparations Before Installation
REPARATIONS BEFORE INSTALLATION Mounting the air inlet panel with a canvas connection (See figure 7a) Relation of ceiling opening to unit and suspension bolt position. (See figure 5) Mounting the air inlet panel directly (See figure 7b) Model A (mm) B (mm) Ceiling surface Ceiling opening... -
Page 7: Indoor Unit Installation
Refer to Table 1 for the dimensions of flare nut spaces and the NDOOR UNIT INSTALLATION appropriate tightening torque. (Overtightening may damage the flare and cause leaks.) When installing optional accessories (except for the air inlet panel), Table 1 read also the installation manual of the optional accessories. Depending on the field conditions, it may be easier to install optional Pipe accessories before the indoor unit is installed. -
Page 8: Drain Piping Work
Cautions for brazing Wrap the supplied large sealing pad over the metal clamp and drain hose to insulate and fix it with clamps. Be sure to carry out a nitrogen blow when brazing. Insulate the complete drain piping inside the building (field Brazing without carrying out nitrogen replacement or releasing supply). -
Page 9: Electric Wiring Work
LECTRIC WIRING WORK Caution for drain socket Do not remove the drain pipe plug. Water might leak out. General instructions The drain outlet is only used to discharge water if the drain pump is not used or before maintenance. Gently put in and All field supplied parts and materials and electric works must out the drain plug. -
Page 10: Wiring Example And How To Set The Remote Controller
Specifications for field supplied fuses and wire When connecting wires of the same gauge, connect them according to the figure. Power supply wiring Model Field fuses Wire Size 45~140 16 A H05VV-U3G Local codes Model Wire Size Use the specified electric wire. Connect the wire securely to the terminal. -
Page 11: Wiring Example
IRING EXAMPLE IELD SETTING Field setting must be made on the remote controller in function of the Fit the power supply wiring of each unit with a switch and fuse as installation condition. shown in figure Setting can be made by changing the "Mode number", "First Power supply code No."... - Page 12 External static pressure settings If there is no change after airflow adjustment in the Settings for external static pressure can be achieved in 2 ways: ventilation paths, be sure to perform setting the automatic airflow adjustment again. Using the airflow automatic adjustment function Contact your dealer if there is no change after Airflow automatic adjustment is the volume of blow-off air that performing airflow adjustment in the ventilation paths,...
-
Page 13: Installation Of The Decoration Panel
Computerised control (forced off and on/off operation) EST OPERATION Wire specifications and how to perform wiring Refer to the installation manual of the outdoor unit. Connect input from outside to terminals T1 and T2 of the The operation lamp of the remote controller will flash when an error terminal board (remote controller to transmission wiring). -
Page 14: Disposal Requirements
If chains are present, unhook the chains. Shut the air inlet grille. (Only for bottom suction.) Refer to item no. 1. After turning on the power, press FILTER SIGN RESET button. The "TIME TO CLEAN AIR FILTER" display is turned off. How to clean air outlet and outside panels Clean with soft cloth. -
Page 15: Wiring Diagram
IRING DIAGRAM : FIELD WIRING : BLACK : ORANGE : CONNECTOR : BLUE : PINK : WIRE CLAMP : BROWN : RED : PROTECTIVE EARTH (SCREW) : GREEN : WHITE : LIVE : GREY : YELLOW : NEUTRAL A1P......PRINTED CIRCUIT BOARD R3T ...... - Page 16 NOTES NOTES...
- Page 17 Control box IN/D OUT/D Control box OUT/D IN/D Control box IN/D OUT/D Control box IN/D OUT/D SETTING...
- Page 18 11.2014...
Need help?
Do you have a question about the AXMP90P7D and is the answer not in the manual?
Questions and answers