Advertisement
Purpose
This document outlines the steps to replace the awning fabric or LED light fabric on a Solera Classic Awning.
Safety
Read and understand all instructions before installing or operating this product. Adhere to all safety labels.
This manual provides general instructions. Many variables can change the circumstances of the instructions,
i.e., the degree of difficulty, operation and ability of the individual performing the instructions. This
manual cannot begin to plot out instructions for every possibility, but provides the general instructions,
as necessary, for effectively interfacing with the device, product or system. Failure to correctly follow the
provided instructions may result in death, serious personal injury, severe product and/or property damage.
The "WARNING" symbol above is a sign that a procedure has a safety risk involved and may cause
death or serious personal injury if not performed safely and within the parameters set forth
The "CAUTION" symbol above is a sign that a safety risk is involved and may cause personal injury
and/or product or property damage if not safely adhered to and within the parameters set forth
Resources Required
• Two or three people
• Cordless or electric drill or
screw gun
Rev: 07.27.22
SOLERA
FABRIC REPLACEMENT
Moving parts can pinch, crush or cut. Keep clear and use caution.
• Appropriate drive bits
• Tape
• Non-permanent marker
CLASSIC AWNING
®
AWNINGS
in this manual.
in this manual.
Page 1
• Cotter pins
• Silicone sealant
CCD-0004486
Advertisement
Table of Contents
Related Manuals for Lippert SOLERA CLASSIC AWNING
Summary of Contents for Lippert SOLERA CLASSIC AWNING
- Page 1 FABRIC REPLACEMENT AWNINGS Purpose This document outlines the steps to replace the awning fabric or LED light fabric on a Solera Classic Awning. Safety Read and understand all instructions before installing or operating this product. Adhere to all safety labels.
- Page 2 SOLERA CLASSIC AWNING ® FABRIC REPLACEMENT AWNINGS Procedure Fabric Removal Extend awning. If equipped, remove the drip cap from the idler end. Make sure the black locking knobs (Fig. 1G) on the support arm (Fig. 1E) are loosened. Determine which travel lock you have and release the travel locks accordingly. A.
- Page 3 SOLERA CLASSIC AWNING ® FABRIC REPLACEMENT AWNINGS B. Original Travel Lock - Release the travel locks (Fig. 2A) on the support arm brackets by reaching behind the support bracket (Fig. 2B) and squeezing the travel lock sides inward, releasing the outer arm (Fig.
- Page 4 SOLERA CLASSIC AWNING ® FABRIC REPLACEMENT AWNINGS Failure to insert a cotter pin into the drive and idler ends of the roll tube before roll tube removal can result in cause personal injury or property damage. Insert a cotter pin (Fig. 5A ) into the drive side and idler side (Fig. 6B) of the roll tube and mark the location of the top of the idler head assembly (Fig.
- Page 5 SOLERA CLASSIC AWNING ® FABRIC REPLACEMENT AWNINGS 12. The fabric will be removed from the roll tube at the idler end of the roll tube. 13. Place the removed assembly onto a level area. 14. Remove the drive and idler head assemblies (Fig. 9A) from the support arms (Fig. 9B) by removing the screws (Fig.
- Page 6 SOLERA CLASSIC AWNING ® FABRIC REPLACEMENT AWNINGS 19. Completely remove idler head and spring assembly (if present) from roll tube. 20. Using non-permanent marker, mark the location of the polycord on the roll tube. 21. Lay fabric flat on a smooth surface. 22.
- Page 7 As a supplier of components to the RV industry, safety, education and customer satisfaction are our primary concerns. Should you have any questions, please do not hesitate to contact us at 432-LIPPERT (432-547-7378) or by email at customerservice@lci1.com. Self-help tips, technical documents, product videos and a training class schedule are available at lippert.com...
Need help?
Do you have a question about the SOLERA CLASSIC AWNING and is the answer not in the manual?
Questions and answers