Advertisement
IT-PMC-3011
10/100/1000M Ethernet SFP Media Converter
(SM & MM)
1
Introduction:
IT-PMC-3011, 10/100/1000Mbps adaptive Gigabit Ethernet fiber
converter uses the switching technology to conduct media
conversion, which meets the standards of IEEE802.3, IEEE802.3u,
IEEE802.3z and IEEE802.3ab.
This kind of media converter supports two types of media network
connections: 10Base-T/100Base-TX/1000Base-T and
1000Base-SX/LX.IT-PMC-3011 can conduct mutual conversion
between 10Base-T/100Base-TX/1000Base-T twisted pair electrical
signals and 1000Base-SX/LX optical signals.
This media converter extends the transmission distance of a
network from 100m over copper wires to 120 Km. This media
converter supports transmission in dual-fiber multi-mode, dual-fiber
single-mode, SFP style fiber-optic connections.
Packing List:
IT-PMC-3011 is shipped with following items.
1. IT-PMC-3011×1
2. 5VDC power adapter ×1(Media converter/5VDC)
3. User manual ×1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Intellisystem IT-PMC-3011
Summary of Contents for Intellisystem IT-PMC-3011
- Page 1 IT-PMC-3011 10/100/1000M Ethernet SFP Media Converter (SM & MM) Introduction: IT-PMC-3011, 10/100/1000Mbps adaptive Gigabit Ethernet fiber converter uses the switching technology to conduct media conversion, which meets the standards of IEEE802.3, IEEE802.3u, IEEE802.3z and IEEE802.3ab. This kind of media converter supports two types of media network connections: 10Base-T/100Base-TX/1000Base-T and 1000Base-SX/LX.IT-PMC-3011 can conduct mutual conversion...
-
Page 2: Pinout Configuration
6. Can insert to 2U 19", 14 slots Rack (power external). Pinout Configuration: Power IT-PMC-3011 adopt the power supply input is 5VDC external. Ethernet (RJ45), Optical fiber interface Optical fiber interface: Optic fiber interface need use in pairs, OUT port is fiber send side, connect another long-range light of interface fiber receive end IN;... - Page 3 Ethernet interface: Ethernet (RJ45) interface supports MDI/MDI-X auto negotiation, can use straight-through cable connect PC or server, use across-over connect cable Switch or HUB. MDI: PIN 1, 2, 3, 6 connects opposite. MID-X: 1→3, 2→6, 3→1, 6→2 MDI/MDI-X 10Base-T/100Base-TX PIN define as follow: MDI-X —...
- Page 4 MDI: RJ45 MDI-X: RJ45 (RX+) (TX+) (RX-) (TX-) (TX+) (RX+) (TX-) (RX-)
- Page 5 LED indications: STATE INDICATION Power Off (Power) BRIGHT Power On Ethernet is not Connected (Fiber Link Port) BRIGHT Ethernet is Connected 10M Ethernet 100M (10/100M) BRIGHT 100M Ethernet Not 1000M Ethernet 1000M BRIGHT 1000M Ethernet Half Duplex (Duplex Mode) FLASHING Full Duplex Ethernet is not Connected...
-
Page 6: Installation
Operating temp:-10°C to 65°C Storage temperature: -20 to 70°C Operating humidity: 5% to 95 % (no condensation) Warranty: 5 years Approvals: FCC, CE, RoHS approvals Applications: Extending 10/100M Ethernet data distance Installation: IT-PMC-3011 provides DIN-rail and wall mounting two types of installation. - Page 7 Wall mounting installation...
-
Page 8: Troubleshooting Instructions
DIN-Rail Installation Troubleshooting instructions: 1. Make sure the power is connected and turned on. 2. Make sure the converter Ethernet and fiber optic cables are connected properly. 3. Check the connections according to the connection diagram. 4. Check the LED Indication status and identify possible problems from the Indication LED table above. -
Page 9: Common Problems
Common Problems: 1. PWR power supply indicator lamp not lighting Cause: 1. Power supply not properly connected 2. Protector tube damaged 3. Power input tie-line in reverse connection 4. Internal power supply circuit with failure Solution: . Check power switch and jack 2. - Page 10 5. Returned to the manufacturer for repair. 4. Network packet loss Solution: 1. Check Ethernet rate or full/half duplex is matched or not. 2. Ethernet (RJ45) port is loose contact, or optic port is loose contact and soiled. 3. Ethernet cable not comply with Ethernet standard. Certifications:...
Need help?
Do you have a question about the IT-PMC-3011 and is the answer not in the manual?
Questions and answers