Advertisement
IT-PMC-3012
10/100/1000M Media Converter
(SM & MM)
1
Introduction:
IT-PMC-3012, 10/100/1000Mbps adaptive Gigabit Ethernet fiber
converter uses the switching technology to conduct media
conversion, which meets the standards of IEEE802.3, IEEE802.3u,
IEEE802.3z and IEEE802.3ab. This kind of media converter
supports two types of media network connections:
10Base-T/100Base-TX/1000Base-T and
1000Base-SX/LX.IT-PMC-3012 can conduct mutual conversion
between 10Base-T/100Base-TX/1000Base-T twisted pair electrical
signals and 1000Base-SX/LX optical signals.
This media converter extends the transmission distance of a
network from 100m over copper wires to 20 Km. This media
converter supports transmission in dual-fiber multi-mode, dual-fiber
single-mode, SC/ST/FC style fiber-optic connections.
Packing List:
IT-PMC-3012 is shipped with following items.
1. IT-PMC-3012×1
2. 5VDC power adapter ×1(Media converter/5VDC)
3. User manual ×1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Intellisystem IT-PMC-3012
Summary of Contents for Intellisystem IT-PMC-3012
- Page 1 IT-PMC-3012 10/100/1000M Media Converter (SM & MM) Introduction: IT-PMC-3012, 10/100/1000Mbps adaptive Gigabit Ethernet fiber converter uses the switching technology to conduct media conversion, which meets the standards of IEEE802.3, IEEE802.3u, IEEE802.3z and IEEE802.3ab. This kind of media converter supports two types of media network connections: 10Base-T/100Base-TX/1000Base-T and 1000Base-SX/LX.IT-PMC-3012 can conduct mutual conversion...
-
Page 2: Pinout Configuration
6. Can insert to 2U 19", 14 slots Rackmount (power external). Pinout Configuration: Power IT-PMC-3012 adopt the power supply input is 5VDC external. Ethernet (RJ45), Optical fiber interface Optical fiber interface: Optic fiber interface need use in pairs, OUT port is fiber send side, connect another long-range light of interface fiber receive end IN;... - Page 3 NOTE: SC, ST or FC, for optic fiber interface, SM is look the same to MM for form. For example, IT-PMC-3012SM/SC, the optic fiber interface (SC) is look the same to Mode3012MM/SC. Ethernet interface: Ethernet (RJ45) interface supports MDI/MDI-X auto negotiation, can use straight-through cable connect PC or server, use across-over connect cable Switch or HUB.
- Page 4 MDI-X — — 4、5、7、8 Note： “TX±”Transfer data±， “RX±”Receive data±， “—”None。 MDI: RJ45 MDI-X: RJ45 (RX+) (TX+) (RX-) (TX-) (TX+) (RX+) (TX-) (RX-)
- Page 5 LED indications: STATE INDICATION Power Off (Power) BRIGHT Power On Ethernet is not Connected (Fiber Link Port) BRIGHT Ethernet is Connected 10M Ethernet 100M (10/100M) BRIGHT 100M Ethernet Not 1000M Ethernet 1000M BRIGHT 1000M Ethernet Half Duplex (Duplex Mode) FLASHING Full Duplex Ethernet is not Connected...
-
Page 6: Installation
Operating temp:-10°C to 65°C Storage temperature: -20 to 70°C Operating humidity: 5% to 95 %(no condensation) Warranty: 5 years Approvals: FCC, CE, RoHS approvals Applications: Extending 10/100/100M Ethernet data distance Installation: IT-PMC-3012 provides DIN-rail and wall mounting two types of installation. - Page 7 Wall mounting installation...
-
Page 8: Troubleshooting Instructions
DIN-Rail Installation Troubleshooting instructions: 1. Make sure the power is connected and turned on. 2. Make sure the converter Ethernet and fiber optic cables are connected properly. 3. Check the connections according to the connection diagram. 4. Check the LED Indication status and identify possible problems from the Indication LED table above. -
Page 9: Common Problems
5. W henever there is a fault, you can contact our technical support after you identify the problem and the alarm. Common Problems: 1. PWR power supply indicator lamp not lighting Cause: 1. Power supply not properly connected. 2. Protector tube damaged. 3. - Page 10 4. Check the rate of Network. 5. Returned to the manufacturer for repair. 4. Network packet loss Solution: 1. Check Ethernet rate or full/half duplex is matched or not. 2. Ethernet (RJ45) port is loose contact, or optic port is loose contact and soiled.
Need help?
Do you have a question about the IT-PMC-3012 and is the answer not in the manual?
Questions and answers