Table of Contents
Advertisement
Quick Links
IT-PMC-1100 P2
1
10/100M Media Converter
(SM & MM)
Introduction:
IT-PMC-1100 P2, 10/100M Media Converter, provides a cost
effective plug-and-play solution for long-range 10Base-T or
100Base-TX Ethernet extensions and added benefit of 10/100
auto-negotiation, making it the perfect choice when planning future
upgrades of 10Base-T networks. IT-PMC-1100 P2 Ethernet Fiber
converters are ultra-miniature in size and feature a shielded RJ45
Ethernet jack, SC/ST/FC style fiber-optic connections. Built-in
auto-sensing capabilities enable full or half-duplex Ethernet
operation with no configuration required!
Packing List:
IT-PMC-1100 P2 is shipped with following items.
1. IT-PMC-1100 P2×1
2. 5VDC power adapter ×1(Media converter/5VDC)
3. User manual ×1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Intellisystem IT-PMC-1100 P2
Summary of Contents for Intellisystem IT-PMC-1100 P2
- Page 1 IT-PMC-1100 P2 10/100M Media Converter (SM & MM) Introduction: IT-PMC-1100 P2, 10/100M Media Converter, provides a cost effective plug-and-play solution for long-range 10Base-T or 100Base-TX Ethernet extensions and added benefit of 10/100 auto-negotiation, making it the perfect choice when planning future upgrades of 10Base-T networks.
-
Page 2: Pinout Configuration
6. Can insert to 2U 19", 14 slots Rackmount (power external). Pinout Configuration: Power IT-PMC-1100 P2 adopt the power supply input is 5VDC external. Ethernet(RJ45), Optical fiber interface Optical fiber interface: Optic fiber interface need use in pairs, OUT port is fiber send side, connect another long-range light of interface fiber receive end IN;... - Page 3 NOTE: SC, ST or FC, for optic fiber interface, SM is look the same to MM for form. For example, IT-PMC-1100 P2SM/SC, the optic fiber interface (SC) is look the same to IT-PMC-1100 P2MM/SC. Ethernet interface: Ethernet (RJ45) interface supports MDI/MDI-X auto negotiation, can use straight-through cable connect PC or server, use across-over connect cable Switch or HUB.
- Page 4 MDI-X — — 4、5、7、8 Note： “TX±”Transfer data±， “RX±”Receive data±， “—”None。 MDI: RJ45 MDI-X: RJ45 (RX+) (TX+) (RX-) (TX-) (TX+) (RX+) (TX-) (RX-)
-
Page 5: Led Indications
LED indications: STATE INDICATION Power Off (Power) BRIGHT Power On 10M Ethernet (10/100M) BRIGHT 100M Ethernet Fiber Optic Unit is Faulty (Fiber Link Port) BRIGHT Fiber Optic Unit is Functional Ethernet is not Connected Link/Act (TX) Port FLASHING Transmitting or Receiving Data Link/Activity) BRIGHT Ethernet is Connected... - Page 6 2, 5 km (MM) optional RJ45 port cable: UTP 5E Fiber connector: 2×SC, 2×ST, 2×FC optional Fiber optic cables: Single Mode:8.3/125,8.7/125,9/125 or 10/125 Muti-Mode:50/125,62.5/125 um Wavelength: 850nm, 1310nm, 1550nm Power supply: External 5VDC input Dimensions: 94.0mm×71.0mm×26.0mm Installation: support DIN-Rail installation Operating temp:-10°C to 65°C Storage temperature: -20 to 70°C Operating humidity: 5% to 95 %( no condensation)
-
Page 7: Installation
Installation: IT-PMC-1100 P2 provides DIN-rail and wall mounting two types of installation. Wall mounting installation... -
Page 8: Troubleshooting Instructions
DIN-Rail Installation Troubleshooting instructions: 1. Make sure the power is connected and turned on. 2. Make sure the converter Ethernet and fiber optic cables are connected properly. 3. Check the connections according to the connection diagram. 4. Check the LED Indication status and identify possible problems from the Indication LED table above. -
Page 9: Common Problems
Common Problems: 1. PWR power supply indicator lamp not lighting Cause: 1. Power supply not properly connected. 2. Protector tube damaged. 3. Power input tie-line in reverse connection. 4. Internal power supply circuit with failure. Solution: . Check power switch and jack. 2. - Page 10 4. Network packet loss Solution: 1. Check Ethernet rate or full/half duplex is matched or not. 2. Ethernet (RJ45) port is loose contact, or optic port is loose contact and soiled. 3. Ethernet cable not comply with Ethernet standard. Certifications:...
Need help?
Do you have a question about the IT-PMC-1100 P2 and is the answer not in the manual?
Questions and answers