Advertisement
The front XP6-MA module positions of each chassis are offset below the rear
XP6-MA module positions so that all of the status indicators are visible.
Cabinets
A BB-25, CAB-3 or CAB-4 Series cabinet will house the CHS-6 chassis with up
to six XP6-MA modules installed on it. Refer to cabinet installation documents
for dimensions.
The BB-XP cabinet houses one or two XP6-MA modules on the internal chas-
sis that is part of the cabinet. Refer to cabinet installation documents for
dimensions.
INSTALLATION STEPS
1.
Cabinet Mounting
In a clean, dry area, mount the backbox using the four holes provided in
the back surface of the cabinet (Figure 3).
2.
Chassis Installation
The CHS-6 chassis is mounted in the BB-25, CAB-3 or CAB-4 Series cabi-
net. It is shipped with two self-threading screws, which are used to fas-
ten the chassis to the back wall of the cabinet (Figure 4).
FIGURE 3. TYPICAL MOUNTING HOLE LOCATIONS
FIGURE 4. MOUNTING THE CHS-6 CHASSIS
The BB-XP cabinet comes with the chassis already installed, so no mounting
is necessary.
3. Module Installation
There are two methods for installing a module in the rear position of a chas-
sis. Method one is for installation of a rear module only, when no module will
be installed in front of it. Refer to Figure 5 for instructions. Method two is for
installation of a rear module when another module will be installed in the
chassis position in front of it. Refer to Figures 6a and 6b for method two. All
necessary screws and standoffs are supplied with the modules.
FIGURE 5. INSTALLATION OF REAR MODULE ONLY, METHOD ONE
2
1
Step 1: Insert the bottom of the XP6-MA module down into a rear slot on the
chassis.
Step 2: Carefully swing the upper edge of the board back towards the back of
the chassis until it touches the two standoffs.
Step 3: Align two 4-40 screws with the two standoffs and tighten.
Step 4: Address and wire the modules according to the instructions in this
manual.
BACKBOX
MOUNTING
HOLES
C0235-00
MOUNT WITH
SELF-THREADING SCREWS
TO BACK OF CABINET
C0236-00
3
C0237-00
The steps in Figures 6A – 6C describe and illustrate module installation when
the rear chassis position and the position in front of it will be filled. Front
position installation is possible only if the rear position is filled with an XP
module.
FIGURE 6A. INSTALLATION OF XP6-MA MODULE IN A REAR CHASSIS
POSITION, METHOD TWO
1
Step 1: Install two long standoffs in the lower mounting holes using two 4-40
nuts as shown.
Step 2: Insert the bottom of the XP6-MA module down into a rear slot on the
chassis.
FIGURE 6B.
3
2
Step 3: Carefully swing the upper edge of the board back towards the back of
the chassis until it touches the two standoffs on the board.
Step 4: Align two 4-40 screws with the two standoffs on the chassis and
tighten.
Step 5: Address and wire the modules according to the instructions in this
manual.
FIGURE 6C. INSTALLATION OF XP6-MA MODULE IN FRONT CHASSIS
POSITION
2
1
Step 1: Insert the bottom edge of the XP6-MA module down into a front slot
of the chassis.
Step 2: Carefully swing the upper edge of the board towards the back of the
chassis until it touches the 1.25" (32 mm) standoffs installed on the
rear module.
Step 3: Align two 4-40 screws with the two standoffs and tighten.
Step 4: Address and wire the modules according to the instructions in this
manual.
WIRING
NOTE: All wiring must conform to applicable local codes, ordinances, and
regulations.
1.
Install module wiring in accordance with the job drawings and appropri-
ate wiring diagrams.
2.
All wiring to the XP6-MA is done via terminal blocks. In order to prop-
erly make electrical connections strip approximately 0.25˝ of insulation
2
C0225-01
4
C0249-01
3
C0226-01
I56-1806-010
7/1/2022
Advertisement
