Impax IM-MULT160-K Instruction Manual page 34

MIG SET-UP GUIDE
Please Note: This information is intended to act as a guide only
Set-Up Guide
Note: This set-up information is intended to act as a guide only.
Please refer to operating manual for further information.
Wire
Material Type Polarity
Steel Solid Wire DCEP
ER70S-6
Flux-Cored DCEN
E71T-11
Stainless Stainless DCEP
Steel Steel
Aluminum Aluminum DCEP
ER4043
0.5mm 0.6mm 0.8mm
Shielding
Gas
V/WFS V/WFS
(20-30 CFH Wire
Flow Rate) Dia (m/min) (m/min) (m/min)
C25 0.6 15.5/3.2 15.5/3.6
0.8 15.5/2.3 15.5/2.4
0.9 15.5/1.8 15.5/2
0.6 16.5/3.2 16.5/3.6
CO
2
0.8 16.5/2.3 16.5/2.4
0.9 16.5/1.8 16.5/2
0.8
0.9
Tri-Mix 0.6 18/4.1 18.5/4.6
0.8 18/2.7 18.5/3.0
0.9 18/2 18.5/2.2 18.5/2.8
Argon 0.8
0.9
Changing Polarity
DCEP
1.0mm 1.2mm 1.6mm
V/WFS V/WFS V/WFS V/WFS
(m/min) (m/min) (m/min) (m/min)
16/4.3 16.5/5.6 17/6.4 17.5/7.8
16/2.8 16.5/3.8 17/5.1 17.5/5.7 18.5/6.4
16/2 16.5/2.8 17/3.6 17.5/4.2 18.5/4.5 19.5/5.1 19.5/7.9 19.5/5.7
17/4.3 18/5.6 18.5/6.4 19/8.6 19.5/9.9 20/10.5
17/2.8 18/3.8 18.5/5.1 19/5.7 19.5/6.4
17/2 18/2.8 18.5/3.6 20/4.2
14/1.8 14.5/3.1 16/3.6 17.5/5.1 18.5/7.6
14.5/1.8 15/2.3
19/5.6 19.5/6.4 20/8.3 21.5/10.2
19/3.8 19.5/4.1 20/5.1 21.5/6.6
19/3.1 19.5/4.1
13/7.6 14/8.1 14.5/10.2 20/8.9
14.5/6.1 16/7.1 17/8.6
33
DCEN
3mm 4.5mm 6.0mm 6.0mm
V/WFS V/WFS V/WFS V/WFS
(m/min) (m/min) (m/min) (m/min)
18/9.7 18.5/10.5
19/7 19.5/7.9 19.5/7.9
20.5/7 22/7.9 22/7.9 23.5/8.6
21/4.1 22/5.5 22/6 22/6
20/8.4 20.5/9.5 21/10.5
17/3.6 18/4.1 19.5/5.6 20.5/6.6
22/8.1 22/9.2 22/9.2 22.5/9.6 23/10.2
21/4.8 21.5/5.6 22/6.1 22/6.1 22.5/6.6
21/9.3
20/7.6 22/9.2 23/9.7
8mm 10mm
V/WFS V/WFS
(m/min)
20/8.9 21.5/10.5
20/5.7 21/7.6
25/9.2
23.5/7 24.5/8
21/7.1
23/7