Advertisement
2.
TECHNICAL SPECIFICATIONS
MODEL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SD800
Input power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 230V 50Hz
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800W
Speed at no load. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 - 3000rpm
Chuck capacity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1.5 - 13mm
Hammer action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0-48000bpm
Drilling capacity for steel. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm
Maximum capacity for wood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32mm
Maximum capacity for concrete . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13mm
Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1kg
Sound pressure level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91.0dB(A)
Sound power level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104.0dB(A)
Vibration level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.71m/s
fig.1
SD800
3. OPERATING INSTRUCTIONS
3.1.
PREPARING DRILL FOR USE.
3.1.1. Ensure the drill is switched off and unplugged from the mains power supply.
3.1.2. Fitting the side handle. (See figs.1&2 item 7) Fit supplementary handle grip by placing the handle assembly over chuck head and
onto the machine neck. Secure by rotating the handle clockwise until it is tight and the handle can no longer be moved. To ensure a
good grip in all circumstances the angle of the handle may be changed by rotating the handle grip anticlockwise until the handle
assemble is loose. Rotate the handle to the desired angle and retighten.
3.1.3
Fitting the depth gauge. (See figs.1&2 item 8) To fit the depth gauge loosen the side handle and pass the gauge through the handle
clamp to the required depth. Rotate the handle to the required angle. As the handle is tightened the depth gauge will also be gripped firmly.
3.2.
DRILL CONTROLS
3.2.1. ON/OFF Variable speed trigger. Your drill has a variable speed control on/off trigger (See figs.1&2 item 2) which increases the speed
the more the trigger is depressed. Adjacent to the trigger is a button that can be used to lock the trigger in the ‘ON’ position for
continuous extended drilling.
3.2.2
Trigger lock. (See figs.1&2 item1) To lock ‘ON’, depress the trigger, push in and hold the button then release the trigger. Release the
lock on button and your drill will continue running accordingly.
3.2.3
To release the lock depress the trigger and release it.
3.2.4
Power failure. If you have the lock on feature engaged during use and your drill becomes disconnected from the power supply,
disengage the lock on feature immediately.
F
WARNING! Before connecting your drill to power supply, ensure it is not in the lock on position as this may result in
damage and personal injury. Depress the trigger to ensure release. DO NOT use the lock on facility for jobs where your drill
p
may need to be stopped suddenly.
3.2.5. Maximum speed setting control. The variable speed trigger has a small rotating knob incorporated into it (See figs.1&2 item 4)
which can be used to control the maximum speed of the drill. When the knob is set to the maximum or + setting the trigger can be fully
depressed allowing the drill to turn at its maximum speed. As the knob is turned towards the minimum or - setting the movement of the
trigger is restricted so that the drill will turn at a lower pre-set speed when the trigger is fully depressed. This facility is useful when
working with materials that should be drilled at a constant, lower speed.
3.2.6. Two speed gearbox.(SD1000 only ) The SD1000 also incorporates a 2 speed mechanical gearbox which used in conjunction with the
other speed controls adds additional versatility to this model.To select the lower speed turn the gear selector knob so that ‘1’ is adjacent to
the arrow on the casing. To select the higher speed turn the gear selector knob so that ‘2’ is adjacent to the arrow on the casing.
( See fig.2 item10 ) It may be necessary to rotate the chuck by hand slightly whilst using the gear selector in order to get the gears to mesh.
F
WARNING! Only change gear when the drill is not turning.
The required speed will depend on the material and task in hand. The following may be used as a general guide.
p
a) Low speeds are recommended for hard materials i.e. stone, ceramic, concrete, high tensile steel, and tasks such as starting
holes without centre punch, driving screws, mixing paint etc.
b) Medium speeds are suitable for plastics and laminates.
c) High speeds recommended for soft materials such as wood, aluminium, copper, bronze and brass.
I
CAUTION: DO NOT run your drill at low to medium speeds for extended periods of time as this may cause drill to overheat.
To cool drill run it without a load for approximately 3 minutes at full speed.
s
3.2.7
Direction of rotation. Select either forward or reverse rotation using the lever mounted directly above the trigger. (See figs.5) The lever
flicks from left to right. Select reverse by moving the lever to the left to be adjacent to the ‘L’ symbol and the trigger lock button. To select
the forward direction flick the lever to the other side to be adjacent to the ’R’ symbol.
I
CAUTION: Do not change direction of rotation whilst the drill is running.
s
2
1. Trigger lock button
2. On/Off switch
3. Forward/reverse
selector
4. Variable speed knob
5. Chuck
6. Drill/impact selector
7. Side handle
8. Depth gauge
9. Chuck key
10.High/low gear knob
(SD1000only)
,
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .SD1000
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .230V 50Hz
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1000W
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 - 1100 / 0 - 3000rpm
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1.5 - 13mm
. . . . . . . . . . . . . . . . . . . . . . . . . . . .0 - 16500 / 0 - 45000bpm
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13mm
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32mm
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16mm
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.5kg
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89.7dB(A)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102.7dB(A)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.25m/s
fig.2
SD1000
2
SD800 & SD1000 - 2 - 110603
Advertisement
