Expansion slot adapter for open pluggable specification (ops) cards (2 pages)
Summary of Contents for NEC 1000BASE-T
Page 1
N8104-201 1000BASE-T 接続ボード(1ch) / 1000BASE-T Adapter N8104-202 1000BASE-T 接続ボード(2ch) / Dual Port 1000BASE-T Adapter N8104-203 1000BASE-T 接続ボード(4ch) / Quad Port 1000BASE-T Adapter ユーザーズガイド / User’s Guide (第 1 版) (1st. Edition) 本書を熟読し、大切に保管してください。 Read this document carefully, and keep at hand so that it is available whenever necessary.
Page 3
Table of contents Precautions for Use -Be sure to read this section - ....... E-2 Safety Indication ......................... E-2 Symbols Used in This Guide .................... E-3 Precautions for Safety ....................... E-4 Introduction ...................... E-8 About this Guide ....................E-8 Text Conventions ......................... E-8 General Description................
Page 5
Note that the basic information, such as the operation procedures of the device and OS, is omitted. No part of this guide may be reproduced or changed in any form without prior written permission of NEC Corporation...
Page 6
이 기기는 가정용(B급) 전자파적합기기로서 주로 가정에서 (가정용 방송통신기자재) 사용하는 것을 목적으로 하며, 모든 지역에서 사용할 수 있습니다. Importer EU Contact: NEC Nederland B.V. Olympia 4, 1213 NT Hilversum, The Netherlands Trademark, name and address of the manufacturer: Intel Corporation 2200 Mission College Blvd.
Page 7
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority and ask for the correct method of disposal. Importer EU Contact: NEC Nederland B.V. Olympia 4, 1213 NT Hilversum, The Netherlands This product is RoHS Compliant.
1.3. LED 表示 LNK/ACT LNK/ACT PORT A PORT A SPEED PORT B PORT B SPEED PORT C 10=OFF 100=GRN 1000=ORG PORT D N8104-201 N8104-202 N8104-203 背面 状態 意味 点灯(橙) 1000Mbpsでリンクが確立しています。 点灯(緑) 100Mbpsでリンクが確立しています。 SPEED 10Mbpsでリンクが確立しています。 消灯 またはリンクパートナーと正常に接続できていません。 (リンクダウン) 点滅(緑) データの送受信があることを示します。 リンクパートナーと正常に接続していることを示します。 点灯(緑)...
Keep this Startup Guide at hand for quick reference at any time necessary. Be sure to read this section carefully. Precautions for Use -Be sure to read this section - The following includes information necessary for proper and safe operation of the product. Safety Indication Follow the instructions in this Guide for your safety to use this product.
Term indication a degree of danger Description of a danger Symbol to draw attention Do not plug the power cord in a nonconforming outlet Use a wall outlet with specified voltage and power type. Otherwise, there is a risk of a fire or current leakage. Symbols Used in This Guide Attentions Indicates a risk of an electric shock.
NEC assumes no liability for any accident resulting in personal injury, death, or property damage if the product has been used in the above conditions.
Page 31
Connection Do not use any unauthorized interface cable. Use only interface cables authorized by NEC and locate a proper device and connector before connecting a cable. Using an authorized cable or connecting a cable to an improper destination may cause a short circuit, resulting in a fire.
Page 32
Precautions for Handling of Internal Devices Do not disassemble, repair, or modify the product yourself Do not disassemble, repair, or modify this product. Doing so may cause an electrical shock or a fire. Do not put the product close to fire, or immerse it in water. Doing so may cause an explosion.
Page 33
Anti-static Measures Installing or Uninstalling Internal Optional Devices (1) To avoid electric hazard and malfunction of the device, be sure to turn off the Power switch of the server and unplug the power cord from outlet before starting work, except for hot-swappable devices.
Introduction Thank you very much for purchasing our products. To maximize the functionality of this product, please read this guide carefully and follow the instructions for proper handling. About this Guide This guide describes how to handle and use this product properly. Keep this guide at hand for your future reference.
This product is Network Interface Card dedicated to the Express5800 series. This products is a server adapter for PCI Express* (PCIe*) v2.1 systems. Each LAN port connects to a Cat 5E/RJ45 connector. Do not install this product to a computer that is not recommended by NEC IMPORTATANT: Corporation.
Page 36
N8104-202 Dual Port 1000BASE-T Adapter N8104-203 Quad Port 1000BASE-T Adapter LAN Port LAN Port Heat sink LAN Controller PCI-Express® Connector Bracket PCI-Express® Connector Bracket Bracket Bracket PCI-Express® Connector PCI-Express® Connector LAN Port A connector provides to access a network. Port id is numbered from “PORT A” to “PORT D”. See the figure.
1.3. LED LNK/ACT LNK/ACT PORT A PORT A SPEED PORT B PORT B SPEED PORT C 10=OFF 100=GRN 1000=ORG PORT D N8104-201 N8104-202 N8104-203 Lamp Status (color) Meaning On (Orange) Link at 1000Mbps speed. On (Green) Link at 100Mbps speed. SPEED Link at 10Mbps speed.
2. Hardware Installation/Uninstallation For hardware installation/uninstallation, refer to the User’s Guide of the server. When the system is up, please turn the power off after shutdown process on the OS. and then unplug the AC power cord. IMPORTANT: For rack-type server, before open the top cover, need to disconnect the cable from this product.
Page 39
Depending on the type of system, installation of this product requires either a standard bracket or a low-profile bracket. NEC provides both of these brackets with the product. By default low-profile bracket is attached. Please replace the bracket according to the following steps as necessary.
Page 40
■N8104-202/203 1. Remove the screw using a Philips screwdriver. 2.Slide the bracket away from the Adapter. 3.Attach the new bracket to the Adapter. 4. Fasten the screw using a Philips screwdriver. E-14...
3. Driver/Software Setup The driver and software of this product is published on NEC web site. Also an installation guide of this product includes in the files on NEC web site. To get the driver and the installation guide, access to the NEC web site.
4. Trouble Shooting 4.1. Unable to Start the System Check the BIOS setting □ Change the setting of the system BIOS of the server about Option ROM expansion. If network boot function is not required, disable the function to expand the Option ROM of this adapter. Need to access system BIOS.
4.2. Unable to Connect the Network Check the link partner (switch, hub, etc.) □ Check a setting or configuration on the link partner. Make sure the link partner setting is correct. If the setting is mis-configured, correct the setting. If the partner’s port is disabled, enable it. If the adapter’s communication mode is set to full duplex mode, make sure that the link partner’s communication mode is also set to full duplex mode.
4.3. Common problems and solutions The Connection fails or an error occurs □ Use a twisted pair cable to connect this adapter. Especially to use for 1000 Mbps, use a twisted pair cable of CAT 5e or better. Also, make sure that the cable is securely attached. □...
5. Notes in operation For OS that support will depend on the device. Please refer to the support matrix. The number that can be installed in the system depends on the model you are using. Please refer to the system configuration guide of the server. Wake On LAN is not supported.