Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for NEC RA1000 Series
Summary of Contents for NEC RA1000 Series
- Page 1 RA1000 Series LAN Adapter Unit User’s Manual...
-
Page 2: Before Using
The present manual relates to the RA1000 Series optional units for the OmniAce II Thermal Dot Recorder. Thank you very much for procuring the RA11-137 LAN adapter Unit. Please read this operation manual carefully in order to properly use the equipment. -
Page 3: Safety Warnings And Cautions
Safety warnings and cautions ● To use this product safety: This product conforms to IEC (International Electrotechnical Commission) safety ratings Class I. Although the product has been manufactured with attention to safety, mishandling or misoperation by the user poses risk of serious incident. In order to avoid such hazards, be sure to read this manual carefully so as to gain a thorough understanding of the contents. -
Page 4: Symbols Used In This Manual
Setting limitations or supplementary description See reference page Equipment RA1000 Series unit Refers to RA1000 Series unit internal memory. Memory Measurement data are stored in this memory when measuring in the Memory and Transient modes. Refers to operation panel key. - Page 5 Symbols used in this manual ........................3 1. How to Use LAN Adapter Unit ..................1-1 1.1. RA1000 Series LAN Adapter Unit (RA11-137) Overview ..........1-2 1.2. LAN Adapter Installation ........................1-2 1.3. Setting LAN for Communication Interface ................... 1-3 1.4.
- Page 6 1. How to Use LAN Adapter Unit 1. How to Use LAN Adapter Unit RA11-137 (95691-2189-0000)
- Page 7 This manual covers the setup for the RA1000 Series when the LAN adapter unit (RA11-137) is installed in the RA1000 Series main body. To use this unit, RA1000 Series firmware version 1.9 or later is required. (You can confirm the version on the Version window on the Maintenance tab in the System screen.) The RA11-137 LAN adapter unit is used to control the RA1000 Series via Ethernet.
- Page 8 1. How to Use LAN Adapter Unit 1.3 Setting LAN for Communication Interface Set up the RA1000 main body according to the communication interface to allow the RA1000 to be controlled by a personal computer or other external equipment through the communication interface.
- Page 9 1. How to Use LAN Adapter Unit 1.4 Direct Control of RA1000 Using LAN The RA1000 can be directly controlled by the host computer via the LAN interface. 1.4.1 LAN Adapter Setup Screen (Main) Choose “Communicate to host using LAN” for the communication function. The following screen appears.
- Page 10 1. How to Use LAN Adapter Unit To change settings such as the IP address after LAN adapter setup, power down NOTE and restart the RA1000. Pressing the screen frame after LAN adapter setup displays the caution screen indicating that the setup cannot be changed. 1.4.3 IP Address Subnet Mask Gateway Address Setup Screen Use the following numeric pad to set the IP address subnet mask gateway address.
- Page 11 Use our Omniviewer (NS2100) to perform remote control of the RA1000 via the LAN. 1.5.1 To Use Omniviewer (NS2100) The Omniviewer (NS2100) is the remote-control and data-display software for the RA1000 Series. Before using NS2100, the IP address set in the LAN adapter should be set on the NS2100 screen.
- Page 12 1. How to Use LAN Adapter Unit If the LAN adapter unit had already been set, setup information other than the NOTE information on communication including the LAN adapter is readout. 1.7 LAN Adapter Specifications Function The LAN adapter unit is an interface board that allows the Omniace II to be controlled from a computer on the network.
- Page 13 (1) No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC San-ei Instruments, Ltd. (2) The information in this document is subject to change without notice.
Need help?
Do you have a question about the RA1000 Series and is the answer not in the manual?
Questions and answers