Regal marathon PPA Series Installation, Operation And Maintenance Instructions

Regal marathon PPA Series Installation, Operation And Maintenance Instructions

Advertisement

Quick Links

PPA & PPC SERIES MOTORS
INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the marathon PPA Series and is the answer not in the manual?

Questions and answers

Summary of Contents for Regal marathon PPA Series

  • Page 1 PPA & PPC SERIES MOTORS INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS...
  • Page 2: Installation

    Proper wheel or pulley removers should be used to prevent shaft and bearing damage. Tapped holes are provided in shaft extensions to assist in the fitment of couplings and/or pulleys. ©2020 Regal Beloit Corporation, All Rights Reserved. MCIM20001E • Form# SB0098E...
  • Page 3 Where higher than recommended axial loads are necessary different bearing types will be required. Please contact Regal Australia for advise. The contact details are provided on page 4. ©2020 Regal Beloit Corporation, All Rights Reserved. MCIM20001E • Form# SB0098E...
  • Page 4 -20°C to 50°C) Ex e or Ex nA or Ex t or combination of them can be used in hazardous locations. Check nameplate before installing motors in hazardous locations. ©2020 Regal Beloit Corporation, All Rights Reserved. MCIM20001E • Form# SB0098E...
  • Page 5: Cable Entries

    RTDs and thermistors can be connected via a the nameplate. standard industrial controller provided that the controller is located in a safe area. ©2020 Regal Beloit Corporation, All Rights Reserved. MCIM20001E • Form# SB0098E...
  • Page 6: Initial Start-Up

    IA/IN ratio and tE time. thoroughly. *Esso is a trademark or tradename of ExxonMobil and is not owned by, or under the control of Regal Beloit Corporation. ©2020 Regal Beloit Corporation, All Rights Reserved. MCIM20001E • Form# SB0098E...
  • Page 7: Sealed Bearings

    Replenishment of grease media should be by means of a hand held grease gun whilst motor is running with relief plate removed. Air operated grease guns should not be used. ©2020 Regal Beloit Corporation, All Rights Reserved. MCIM20001E • Form# SB0098E...
  • Page 8 65x140x33 4800 6313 65x140x33 4200 6314 70x150x35 4000 6314 70x150x35 2500 6316 80x170x39 2000 6316 80x170x39 2000 6318 90x190x43 2000 6318 90x190x43 2000 6318 90x190x43 2000 6318 90x190x43 2000 ©2020 Regal Beloit Corporation, All Rights Reserved. MCIM20001E • Form# SB0098E...
  • Page 9 6317 85x180x41 14000 NU317 6800 6316 80x170x39 13000 NU318 90x190x43 13000 6324 120x260x55 7000 NU324 120x260x55 10000 6326 130x280x58 6200 NU326 130x280x58 9000 6326 130x280x58 6200 NU328 140x210x62 7500 ©2020 Regal Beloit Corporation, All Rights Reserved. MCIM20001E • Form# SB0098E...
  • Page 10 ©2020 Regal Beloit Corporation, All Rights Reserved. MCIM20001E • Form# SB0098E...
  • Page 11 F: +66 2447 3500 PRESENT IN MACKAY SOUTH AUSTRALIA WESTERN AUSTRALIA T: 1300 888 853 Regal and Marathon are trademarks of Regal Beloit Corporation or one of its affiliated companies. ©2018, 2020 Regal Beloit Corporation, All Rights Reserved. MCIM20001E • Form# SB0098E...

This manual is also suitable for:

Marathon ppc series

Table of Contents