Lenovo ThinkCentre A70 7099 Hardware Maintenance Manual
  1. Manuals
  2. Brands
  3. Lenovo Manuals
  4. Desktop
  5. ThinkCentre A70 7099
  6. Hardware maintenance manual

Lenovo ThinkCentre A70 7099 Hardware Maintenance Manual

Lenovo thinkcentre a70 7099: user guide
Hide thumbs
Table of Contents

Advertisement

Quick Links

ThinkCentre
Hardware Maintenance Manual
Machine Types: 0864, 0889, 5023, 7099, 7844, and 7846

Advertisement

Table of Contents
loading

Related Manuals for Lenovo ThinkCentre A70 7099

Summary of Contents for Lenovo ThinkCentre A70 7099

  • Page 1 ThinkCentre Hardware Maintenance Manual Machine Types: 0864, 0889, 5023, 7099, 7844, and 7846...
  • Page 3 ThinkCentre Hardware Maintenance Manual...
  • Page 4 Second Edition (June 2010) © Copyright Lenovo 2010. LENOVO products, data, computer software, and services have been developed exclusively at private expense and are sold to governmental entities as commercial items as defined by 48 C.F.R. 2.101 with limited and restricted rights to use, reproduction and disclosure.

  • Page 5: Table Of Contents

    Safety inspection guide . Handling electrostatic discharge-sensitive devices . Grounding requirements . Safety notices (multi-lingual translations) . Chapter 3. General information ..39 Lenovo ThinkVantage Tools . ThinkVantage Productivity Center . Lenovo Welcome Additional information resources . Specifications .
  • Page 6 Completing the parts replacement Chapter 10. FRU lists ..159 Machine type 7099 Machine type 7844 Chapter 11. Additional service information ... . 179 Security features .

  • Page 7: Chapter 1. About This Manual

    This manual contains service and reference information for ThinkCentre machine types listed on the front cover. This manual is intended only for trained Service Providers who are familiar with Lenovo Note: Be sure to read and understand the Chapter 2, “Safety information,” on page 3 before using the information in this manual.

  • Page 8: Important Information About Replacing Rohs Compliant Frus

    FRU part numbers. Lenovo plans to transition to RoHS compliance well before the implementation date and expects its suppliers to be ready to support Lenovo’s requirements and schedule in the EU. Products sold in 2005 will contain some RoHS compliant FRUs.

  • Page 9: Chapter 2. Safety Information

    After service, reinstall all safety shields, guards, labels, and ground wires. Replace any safety device that is worn or defective. v Reinstall all covers correctly before returning the machine to the customer. Electrical safety © Copyright Lenovo 2010...
  • Page 10 CAUTION: Electrical current from power, telephone, and communication cables can be hazardous. To avoid personal injury or equipment damage, disconnect the attached power cords, telecommunication systems, networks, and modems before you open the centre covers, unless instructed otherwise in the installation and configuration procedures.

  • Page 11: Voltage-Selection Switch

    v Always look carefully for possible hazards in your work area. Examples of these hazards are moist floors, nongrounded power extension cables, power surges, and missing safety grounds. v Do not touch live electrical circuits with the reflective surface of a plastic dental mirror.

  • Page 12: Handling Electrostatic Discharge-Sensitive Devices

    If any unsafe conditions are present, you must determine how serious the apparent hazard could be and whether you can continue without first correcting the problem. Consider these conditions and the safety hazards they present: v Electrical hazards, especially primary power (primary voltage on the frame can cause serious or fatal electrical shock).

  • Page 13: Grounding Requirements

    v Prevent the part from touching your clothing. Most clothing is insulative and retains a charge even when you are wearing a wrist strap. v Use the black side of a grounded work mat to provide a static-free work surface. The mat is especially useful when handling ESD-sensitive devices.
  • Page 14 v Connect to properly wired outlets any equipment that will be attached to this product. v When possible, use one hand only to connect or disconnect signal cables. v Never turn on any equipment when there is evidence of fire, water, or structural damage.
  • Page 15 CAUTION: When replacing the lithium battery, use only Part Number 45C1566 or an equivalent type battery recommended by the manufacturer. If your system has a module containing a lithium battery, replace it only with the same module type made by the same manufacturer. The battery contains lithium and can explode if not properly used, handled, or disposed of.
  • Page 16 CAUTION: The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.
  • Page 17 Chapter 2. Safety information...
  • Page 18 Hardware Maintenance Manual...
  • Page 19 ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) Chapter 2. Safety information...
  • Page 20 PERIGO A corrente elétrica proveniente de cabos de alimentação, de telefone e de comunicações é perigosa. Para evitar risco de choque elétrico: v Não conecte nem desconecte nenhum cabo ou execute instalação, manutenção ou reconfiguração deste produto durante uma tempestade com raios. v Conecte todos os cabos de alimentação a tomadas elétricas corretamente instaladas e aterradas.
  • Page 21 CUIDADO: Ao substituir a bateria de lítio, utilize apenas uma bateria com Número de Peça 45C1566 ou um tipo de bateria equivalente recomendado pelo Se o seu sistema possui um módulo com uma bateria de lítio, substitua-o apenas por um módulo do mesmo tipo e do mesmo fabricante.
  • Page 22 CUIDADO: O botão de controle de alimentação do dispositivo e o botão para ligar/desligar da fonte de alimentação não desligam a corrente elétrica fornecida ao dispositivo. O dispositivo também pode ter mais de um cabo de alimentação. Para remover toda a corrente elétrica do dispositivo, assegure que todos os cabos de alimentação estejam desconectados da fonte de alimentação.
  • Page 23 Chapter 2. Safety information...
  • Page 24 Hardware Maintenance Manual...
  • Page 25 Chapter 2. Safety information...
  • Page 26 Hardware Maintenance Manual...
  • Page 27 DANGER Le courant électrique provenant de l’alimentation, du téléphone et des câbles de transmission peut présenter un danger. Pour éviter tout risque de choc électrique : v Ne manipulez aucun câble et n’effectuez aucune opération d’installation, d’entretien ou de reconfiguration de ce produit au cours d’un orage. v Branchez tous les cordons d’alimentation sur un socle de prise de courant correctement câblé...
  • Page 28 ATTENTION: Remplacer la pile au lithium usagée par une pile de référence identique exclusivement, (référence 45C1566), ou suivre les instructions du fabricant qui en définit les équivalences. Si votre système est doté d’un module contenant une pile au lithium, vous devez le remplacer uniquement par un module identique, produit par le même fabricant.
  • Page 29 ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ATTENTION: Soulevez la machine avec précaution. ATTENTION: L’interrupteur de contrôle d’alimentation de l’unité et l’interrupteur dubloc d’alimentation ne coupent pas le courant électrique alimentantl’unité. En outre, le système peut être équipé de plusieurs cordonsd’alimentation. Pour mettre l’unité...
  • Page 30 VORSICHT An Netz-, Telefon- und Datenleitungen können gefährliche Spannungen anliegen. Aus Sicherheitsgründen: v Bei Gewitter an diesem Gerät keine Kabel anschließen oder lösen. Ferner keine Installations-, Wartungs- oder Rekonfigurationsarbeiten durchführen. v Gerät nur an eine Schutzkontaktsteckdose mit ordnungsgemäß geerdetem Schutzkontakt anschließen. v Alle angeschlossenen Geräte ebenfalls an Schutzkontaktsteckdosen mit ordnungsgemäß...
  • Page 31 CAUTION: Eine verbrauchte Lithiumbatterie nur durch eine Batterie mit der Teilenummer 45C1566 oder eine gleichwertige, vom Hersteller empfohlene Batterie ersetzen. Enthält das System ein Modul mit einer Lithiumbatterie, dieses nur durch ein Modul desselben Typs und von demselben Hersteller ersetzen. Die Batterie enthält Lithium und kann bei unsachgemäßer Verwendung, Handhabung oder Entsorgung explodieren.
  • Page 32 ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ACHTUNG: Arbeitsschutzrichtlinien beim Anheben der Maschine beachten. ACHTUNG: Mit dem Netzschalter an der Einheit und am Netzteil wird die Stromversorgung für die Einheit nicht unterbrochen. Die Einheit kann auch mit mehreren Netzkabeln ausgestattet sein.
  • Page 33 Chapter 2. Safety information...
  • Page 34 Hardware Maintenance Manual...
  • Page 35 Chapter 2. Safety information...
  • Page 36 PERICOLO La corrente elettrica proveniente dai cavi di alimentazione, del telefono e di comunicazione può essere pericolosa. Per evitare il rischio di scosse elettriche: v Non collegare o scollegare qualsiasi cavo oppure effettuare l’installazione, la manutenzione o la riconfigurazione del prodotto durante un temporale. v Collegare tutti i fili elettrici a una presa di alimentazione correttamente cablata e dotata di messa a terra.
  • Page 37 ATTENZIONE: Quando si sostituisce la batteria al litio, utilizzare solo il Numero parte 45C1566 o un tipo di batteria equivalente consigliato dal produttore. Se sul sistema è presente un modulo che contiene una batteria al litio, sostituirlo solo con un tipo di modulo dello stesso tipo della stessa casa di produzione.
  • Page 38 ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) ATTENZIONE: Prestare attenzione nel sollevare l’apparecchiatura. ATTENZIONE: Il pulsante di controllo dell’alimentazione presente sull’unità e l’interruttore dell’alimentatore non disattivano l’alimentazione corrente fornita all’unità. E’ possibile che l’unità disponga di più cavi di alimentazione. Per disattivare l’alimentazione dall’unità, accertarsi che tutti i cavi di alimentazione siano scollegati dalla fonte di alimentazione.
  • Page 39 Chapter 2. Safety information...
  • Page 40 Hardware Maintenance Manual...
  • Page 41 PELIGRO La corriente eléctrica procedente de cables de alimentación, teléfonos y cables de comunicación puede ser peligrosa. Para evitar el riesgo de descarga eléctrica: v No conecte ni desconecte los cables ni realice ninguna tarea de instalación, mantenimiento o reconfiguración de este producto durante una tormenta eléctrica.
  • Page 42 PRECAUCIÓN: Cuando sustituya una batería de litio, utilice solamente una batería número de pieza 45C1566 u otra de tipo equivalente recomendada por el fabricante. Si su sistema dispone de un módulo que contiene una batería de litio, reemplácelo sólo con el mismo tipo de módulo, del mismo fabricante. La batería contiene litio y puede explotar si no se utiliza, manipula o desecha correctamente.
  • Page 43 ≥18 kg (37 lbs) ≥32 kg (70.5 lbs) ≥55 kg (121.2 lbs) PRECAUCIÓN: Adopte procedimientos seguros al levantar el equipo. PRECAUCIÓN: El botón de control de alimentación del dispositivo y el interruptor de alimentación de la fuente de alimentación no desconectan la corriente eléctrica suministrada al dispositivo.
  • Page 44 Hardware Maintenance Manual...

  • Page 45: Chapter 3. General Information

    Lenovo Welcome The Lenovo Welcome program introduces some innovative built-in features of Lenovo to you and guides you through some important setup tasks to help you make the most of your computer. Note: The Lenovo Welcome program is only available on computers preinstalled with the Windows 7 operating system from Lenovo.

  • Page 46: Additional Information Resources

    Additional information resources If you have Internet access, the most up-to-date information for your computer is available at: http://www.lenovo.com/support You can find the following information: v Customer Replaceable Unit (CRU) installation or replacement instructions v Downloads and drivers v Parts information...

  • Page 47: Specifications

    Specifications This section lists the physical specifications for your computer. For machine types: 0864, 7099, and 7846. Dimensions Width: 160 mm (6.3 inches) Height: 355 mm (14 inches) Depth: 355 mm (14 inches) Weight Maximum configuration as shipped: 6.5 to 7 kg (14.3 to 15.4 lbs) (without package) Maximum configuration as shipped: 10.5 kg (23.15 lbs) (with package) Environment Air temperature:...

  • Page 48: For Machine Types: 0889, 5023, And 7844

    For machine types: 0889, 5023, and 7844. Dimensions Width: 97 mm (3.8 inches) Height: 333 mm (13.1 inches) Depth: 368 mm (14.5 inches) Weight Maximum configuration as shipped: 6 to 6.5 kg (13.2 to 14.3 lbs) (without package) Maximum configuration as shipped: 8.5 kg (18.7 lbs) (with package) Environment Air temperature: Operating: 10°...

  • Page 49: Chapter 4. General Checkout

    If possible, have this information available when requesting assistance from Service Support and Engineering functions. v Machine type and model v Processor or hard disk drive upgrades © Copyright Lenovo 2010...
  • Page 50 v Failure symptom – Do diagnostics indicate a failure? – What, when, where, single, or multiple systems? – Is the failure repeatable? – Has this configuration ever worked? – If it has been working, what changes were made prior to it failing? –...

  • Page 51: Chapter 5. Diagnostic Programs

    To run the Lenovo ThinkVantage Toolbox program on the Windows 7 operating system, click Start → All Programs → Lenovo ThinkVantage Tools → System Health and Diagnostics.

  • Page 52: Pc-Doctor For Dos

    PC-Doctor for DOS You can also download the latest version of the PC-Doctor for DOS diagnostic program from http://www.lenovo.com/support. The PC-Doctor for DOS diagnostic program runs independently of the Windows operating system. Use the PC-Doctor for DOS diagnostic program if you are unable to start the Windows operating system.

  • Page 53: Running Tests

    v For online help, select F1. Running tests There are four ways to run the diagnostic tests. v Using the cursor movement keys, highlight Run Normal Test or Run Quick Test from the Diagnostics menu and then press Enter. This automatically runs a pre-defined group of tests from each test category. Run Normal Test runs a more extensive set of tests than Run Quick Test does and takes longer to complete.

  • Page 54: Viewing The Test Log

    v Text: Description of the error. Note: See “Diagnostic error codes” on page 54 for error code listings. Quick and Full erase - hard disk drive The diagnostics program offers two hard disk drive format utilities: v Quick Erase Hard Drive v Full Erase Hard Drive Quick Erase Hard Drive provides a DOS utility that performs the following: v Destroys the Master Boot Record (MBR) on the hard disk drive.

  • Page 55: Chapter 6. Using The Setup Utility

    Set Power-On Password v Set Administrator Password You do not have to set a password to use your computer. However, using a password improves computing security. If you decide to set a password, read the following sections. © Copyright Lenovo 2010...

  • Page 56: Password Considerations

    Password considerations A password can be any combination of up to 16 (1 to 16) alphabetic and numeric characters. For security reasons, it is recommended to use a strong password that cannot be easily compromised. To set a strong password, use the following guidelines: Note: The Setup Utility program passwords are not case sensitive.

  • Page 57: Enabling Or Disabling A Device

    Enabling or disabling a device This section provides instructions on how to enable or disable user access to a device. SATA Controller Serial Port1 Address USB Setup To enable or disable a device, do the following: 1. Start the Setup Utility program. See “Starting the Setup Utility program” on page 49.

  • Page 58: Viewing Or Changing The Startup Device Sequence

    2. Repeatedly press and release the F12 key when turning on the computer. When the Startup Device Menu opens, release the F12 key. 3. Select the desired startup device on the Startup Device Menu and press Enter. Note: Selecting a startup device on the Startup Device Menu does not permanently change the startup device sequence.

  • Page 59: Chapter 7. Symptom-To-Fru Index

    System board power supply connectors v Microprocessor(s) connection Check the power cord for continuity. Check the power-on switch for continuity. © Copyright Lenovo 2010 FRU/Action Check the configuration and ensure the start-up drive is in the boot sequence. Install an operating system on the boot drive.

  • Page 60: Diagnostic Error Codes

    Diagnostic error codes Refer to the following diagnostic error codes when using the diagnostic tests. See “Running tests” on page 47 for the specific type for information about the diagnostic programs. In the following index, X can represent any number. Diagnostic Error Code 000-000-XXX BIOS Test Passed...
  • Page 61 Diagnostic Error Code 000-038-XXX BIOS Extension failure 000-039-XXX BIOS DMI data error 000-195-XXX BIOS Test aborted by user 000-196-XXX BIOS test halt, error threshold exceeded 000-197-XXX BIOS test warning 000-198-XXX BIOS test aborted 000-199-XXX BIOS test failed, cause unknown 000-250-XXX BIOS APM failure 000-270-XXX BIOS ACPI failure...
  • Page 62 Diagnostic Error Code 001-024-XXX System Addressing test failure 001-025-XXX System Checksum Value error 001-026-XXX System FLASH data error 001-027-XXX System Configuration/Setup error 001-032-XXX System Device Controller failure 001-034-XXX System Device Buffer Allocation failure 001-035-XXX System Device Reset condition detected 001-036-XXX System Register error 001-038-XXX System Extension failure...
  • Page 63 Diagnostic Error Code 001-197-XXX System test warning 001-198-XXX System test aborted 001-199-XXX System test failed, cause unknown 001-250-XXX System ECC error 001-254-XXX 001-255-XXX 001-256-XXX 001-257-XXX System DMA error 001-260-XXX 001-264-XXX System IRQ error 001-268-XXX System IRQ1 failure 001-269-XXX System IRQ2 failure 001-270-XXX System IRQ3 failure 001-271-XXX...
  • Page 64 Diagnostic Error Code 001-275-XXX System IRQ8 failure 001-276-XXX System IRQ9 failure 001-277-XXX System IRQ10 failure 001-278-XXX System IRQ11 failure 001-279-XXX System IRQ12 failure 001-280-XXX System IRQ13 failure 001-281-XXX System IRQ14 (hard disk drive) failure 001-282-XXX System IRQ15 failure 001-286-XXX 001-287-XXX 001-288-XXX System Timer failure 001-292-XXX...
  • Page 65 Diagnostic Error Code 005-010-XXX 005-011-XXX 005-012-XXX 005-013-XXX Video Signal failure 005-016-XXX Video Simple Pattern test failure 005-024-XXX Video Addressing test failure 005-025-XXX Video Checksum Value error 005-027-XXX Video Configuration/Setup error 005-031-XXX Video Device Cable failure 005-032-XXX Video Device Controller failure 005-036-XXX Video Register error 005-038-XXX...
  • Page 66 Diagnostic Error Code 005-198-XXX Video test aborted 005-199-XXX Video test failed, cause unknown 005-2XX-XXX 005-3XX-XXX Video subsystem error 006-000-XXX Diskette interface Test Passed 006-0XX-XXX Diskette interface error 006-195-XXX Diskette interface Test aborted by user 006-196-XXX Diskette interface test halt, error threshold exceeded 006-197-XXX Diskette interface test warning...
  • Page 67 Diagnostic Error Code 011-000-XXX Serial port Interface Test Passed 011-001-XXX Serial port Presence 011-002-XXX 011-003-XXX Serial port Timeout/Parity error 011-013-XXX 011-014-XXX Serial port Control Signal/Loopback test failure 011-015-XXX Serial port External Loopback failure 011-027-XXX Serial port Configuration/Setup error 011-03X-XXX 011-04X-XXX Serial port failure 011-195-XXX Serial port Test aborted by user...
  • Page 68 Diagnostic Error Code 011-199-XXX Serial port test failed, cause unknown 011-2XX-XXX Serial port signal failure 014-000-XXX Parallel port Interface Test Passed 014-001-XXX Parallel port Presence 014-002-XXX 014-003-XXX Parallel port Timeout/Parity error 014-013-XXX 014-014-XXX Parallel port Control Signal/Loopback test failure 014-015-XXX Parallel port External Loopback failure 014-027-XXX Parallel port Configuration/Setup error...
  • Page 69 Diagnostic Error Code 014-198-XXX Parallel port test aborted 014-199-XXX Parallel port test failed, cause unknown 014-2XX-XXX 014-3XX-XXX Parallel port failure 015-000-XXX USB port Interface Test Passed 015-001-XXX USB port Presence 015-002-XXX USB port Timeout 015-015-XXX USB port External Loopback failure 015-027-XXX USB port Configuration/Setup error 015-032-XXX...
  • Page 70 Diagnostic Error Code 015-196-XXX USB port test halt, error threshold exceeded 015-197-XXX USB port test warning 015-198-XXX USB port test aborted 015-199-XXX USB port test failed, cause unknown 018-000-XXX PCI Card Test Passed 018-0XX-XXX PCI Card Failure 018-195-XXX PCI Card Test aborted by user 018-196-XXX PCI Card test halt, error threshold exceeded 018-197-XXX...
  • Page 71 Diagnostic Error Code 018-198-XXX PCI Card test aborted 018-199-XXX PCI Card test failed, cause unknown 018-250-XXX PCI Card Services error 020-000-XXX PCI Interface Test Passed 020-0XX-XXX PCI Interface error 020-195-XXX PCI Test aborted by user 020-196-XXX PCI test halt, error threshold exceeded 020-197-XXX PCI test warning 020-198-XXX...
  • Page 72 Diagnostic Error Code 020-199-XXX PCI test failed, cause unknown 020-262-XXX PCI system error 025-000-XXX IDE interface Test Passed 025-00X-XXX 025-01X-XXX IDE interface failure 025-027-XXX IDE interface Configuration/Setup error 025-02X-XXX 025-03X-XXX 025-04X-XXX IDE Interface failure 025-195-XXX IDE interface Test aborted by user 025-196-XXX IDE interface test halt, error threshold exceeded...
  • Page 73 Diagnostic Error Code 025-198-XXX IDE interface test aborted 025-199-XXX IDE interface test failed, cause unknown 030-000-XXX SCSI interface Test Passed 030-00X-XXX 030-01X-XXX SCSI interface failure 030-027-XXX SCSI interface Configuration/Setup error 030-03X-XXX 030-04X-XXX SCSI interface error 030-195-XXX SCSI interface Test aborted by user 030-196-XXX SCSI interface test halt, error threshold exceeded...
  • Page 74 Diagnostic Error Code 030-198-XXX SCSI interface test aborted 030-199-XXX SCSI interface test failed, cause unknown 035-000-XXX RAID interface Test Passed 035-0XX-XXX RAID interface Failure 035-195-XXX RAID interface Test aborted by user 035-196-XXX RAID interface test halt, error threshold exceeded 035-197-XXX RAID interface test warning 035-198-XXX RAID interface test aborted...
  • Page 75 Diagnostic Error Code 071-000-XXX Audio port Interface Test Passed 071-00X-XXX 071-01X-XXX 071-02X-XXX Audio port error 071-03X-XXX Audio port failure 071-04X-XXX Audio port failure 071-195-XXX Audio port Test aborted by user 071-196-XXX Audio port test halt, error threshold exceeded 071-197-XXX Audio port test warning 071-198-XXX Audio port test aborted 071-199-XXX...
  • Page 76 Diagnostic Error Code 080-XXX-XXX Game Port interface Error 080-195-XXX Game Port interface Test aborted by user 080-196-XXX Game Port interface test halt, error threshold exceeded 080-197-XXX Game Port interface test warning 080-198-XXX Game Port interface test aborted 080-199-XXX Game Port interface test failed, cause unknown 086-000-XXX Mouse Port interface Test Passed...
  • Page 77 Diagnostic Error Code 086-197-XXX Mouse Port interface test warning 086-198-XXX Mouse Port interface test aborted 086-199-XXX Mouse Port interface test failed, cause unknown 089-000-XXX Microprocessor Test Passed 089-XXX-XXX Microprocessor failure 089-195-XXX Microprocessor Test aborted by user 089-196-XXX Microprocessor test halt, error threshold exceeded 089-197-XXX Microprocessor test warning...
  • Page 78 Diagnostic Error Code 089-199-XXX Microprocessor test failed, cause unknown 170-000-XXX Voltage Sensor(s) Test Passed 170-0XX-XXX Voltage Sensor(s) failure 170-195-XXX Voltage Sensor(s) Test aborted by user 170-196-XXX Voltage Sensor(s) test halt, error threshold exceeded 170-197-XXX Voltage Sensor(s) test warning 170-198-XXX Voltage Sensor(s) test aborted 170-199-XXX Voltage Sensor(s) test failed, cause unknown 170-250-XXX...
  • Page 79 Diagnostic Error Code 175-195-XXX Thermal Sensor(s) Test aborted by user 175-196-XXX Thermal Sensor(s) test halt, error threshold exceeded 175-197-XXX Thermal Sensor(s) test warning 175-198-XXX Thermal Sensor(s) test aborted 175-199-XXX Thermal Sensor(s) test failed, cause unknown 175-250-XXX 175-251-XXX Thermal Sensor(s) limit error 185-000-XXX Asset Security Test Passed 185-XXX-XXX...
  • Page 80 Diagnostic Error Code 206-000-XXX Diskette Drive Test Passed 206-XXX-XXX Diskette Drive error 215-000-XXX CD-ROM Drive Test Passed 215-XXX-XXX CD-ROM Drive error 217-000-XXX Hard Disk Drive Test Passed 217-25X-XXX 217-26X-XXX Hard Disk Drive (IDE) error 217-28X-XXX 217-29X-XXX Hard Disk Drive (SCSI) error 220-000-XXX Hi-Capacity Cartridge Drive Test Passed 220-XXX-XXX...
  • Page 81 Diagnostic Error Code 305-250-XXX Monitor DDC self test failure 415-000-XXX Modem Test Passed 415-XXX-XXX Modem error FRU/Action 1. Run Setup to enable DDC 2. Cable 3. Monitor 4. Video card 5. System board No action Remove the Modem and re-test the system Chapter 7.

  • Page 82: Beep Symptoms

    Beep symptoms Beep symptoms are tones or a series of tones separated by pauses (intervals without sound) during POST. The following tables describes beep symptoms. Beep Symptom 2 short beeps CMOS setting error 1 long and 2 short beeps Monitor or video adapter card error 1 long and 9 short beeps BIOS ROM error Continuous long beeps...

  • Page 83: Post Error Codes

    POST error codes Each time you power-on the system, it performs a series of tests that check the operation of the system and some options. This series of tests is called the Power-On Self-Test, or POST. POST does the following operations. v Checks some basic system-board operations v Checks the memory operation v Starts the video operation...
  • Page 84 POST Error Message Press TAB to show POST screen Error: Non-System disk or disk error Replace and press any key when ready Hardware Maintenance Manual Description/Action Pressing the TAB key permits the user to toggle between the default POST display screen and a custom POST display screen.

  • Page 85: Miscellaneous Error Messages

    Miscellaneous error messages Message/Symptom Changing display colors Computer will not power-off. See “Power Supply Problems” on page 53. Computer will not RPL from server Computer will not perform a Wake on LAN (if applicable) Dead computer. See “Power Supply Problems” on page 53. Diskette drive in-use light remains on or does not light when drive is active.

  • Page 86: Undetermined Problems

    Message/Symptom Non-system disk or disk error-type message with a known-good diagnostic diskette. Other display symptoms not listed above (including blank or illegible display) Power-on indicator or hard disk drive in-use light not on, but computer works correctly Printer problems Program loads from the hard disk with a known-good diagnostics diskette in the first 3.5-inch diskette drive RPL computer cannot access programs from...
  • Page 87 e. External Cache f. External Cache RAM g. Hard disk drive h. Diskette drive 3. Turn on the power and the computer to re-test the system. 4. Repeat steps 1 through 3 until you find the failing device or adapter cards. If all devices and adapter cards have been removed, and the problem continues, replace the system board.
  • Page 88 Hardware Maintenance Manual...

  • Page 89: Chapter 8. Replacing Frus (Machine Types: 0864, 7099, And 7846.)

    Figure 1. Front connector, control, and indicator locations 1 Hard disk drive activity indicator 2 Power indicator 3 Power switch 4 Optical drive eject/close button © Copyright Lenovo 2010 5 USB connector 6 Headphone connector 7 Microphone connector 8 USB connector...

  • Page 90: Locating Connectors And Parts On The Rear Of Your Computer

    Locating connectors and parts on the rear of your computer Figure 2 shows the locations of the connectors and parts on the rear of your computer. Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer. Figure 2.

  • Page 91: Locating Components

    Locating components Figure 3 shows the locations of the various components in your computer. To remove the computer cover and gain access to the inside of the computer, see “Removing the computer cover” on page 88. Figure 3. Component locations 1 Heat sink and fan assembly (with a microprocessor underneath) 2 Memory modules (2)

  • Page 92: Locating Parts On The System Board

    Locating parts on the system board Figure 4 shows the locations of the parts on the system board. Figure 4. System board part locations 1 Microprocessor 2 Microprocessor fan connector 3 Memory slots (2) 4 24-pin power connector 5 Front panel connector 6 SATA connectors (3) 7 Clear CMOS (Complementary Metal Oxide Semiconductor) /Recovery jumper...

  • Page 93: Locating Internal Drives

    Locating internal drives Internal drives are devices that your computer uses to read and store data. You can add drives to your computer to increase storage capacity and enable your computer to read other types of media. Internal drives are installed in bays. In this manual, the bays are referred to as bay 1, bay 2, and so on.

  • Page 94: Removing The Computer Cover

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove the computer cover.
  • Page 95 5. Remove the two screws that secure the computer cover and slide the computer cover to the rear to remove it. Figure 6. Removing the computer cover Chapter 8. Replacing FRUs - Tower computers...

  • Page 96: Removing And Reinstalling The Front Bezel

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove and reinstall the front bezel.

  • Page 97: Installing Or Replacing A Pci Card

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a PCI card.
  • Page 98 3. At the rear of the computer, remove the screw that secures the PCI card latch. Figure 9. Removing the screw that secures the PCI card latch 4. Do one of the following: v If you are replacing a PCI card, open the PCI card latch and remove the old PCI card that is currently installed, as shown in Figure 10 on page 93.
  • Page 99 Note: If the PCI card is secured in place by a retaining latch 1 , press the retaining latch to release the PCI card from the latch. Then, grasp the PCI card by the edges and carefully pull it out of the PCI card slot. If necessary, alternate moving each side of the PCI card a small and equal amount until it is completely removed from the slot.

  • Page 100: Installing Or Replacing A Memory Module

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a memory module.
  • Page 101 4. Locate the memory slots on the system board. See “Locating parts on the system board” on page 86. 5. Remove any parts and disconnect any cables that might prevent your access to the memory slots. 6. Do one of the following: v If you are replacing a memory module, open the retaining clips and remove the old memory module that is currently installed.

  • Page 102: Replacing The Battery

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support Your computer has a special type of memory that maintains the date, time, and configuration information for built-in features.

  • Page 103: Replacing The Power Supply Assembly

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the power supply assembly.
  • Page 104 DANGER Hazardous moving parts. Keep fingers and other body parts away. CAUTION: Never remove the cover on a power supply or any part that has the following label attached. Hazardous voltage, current, and energy levels are present inside any component that has this label attached.
  • Page 105 4. Lay the computer on its side and remove the four screws that secure the power supply assembly. Figure 17. Removing the screws that secure the power supply assembly 5. Slide the power supply assembly a little bit forward and then remove it from the chassis.

  • Page 106: Replacing The Heat Sink And Fan Assembly

    8. Install the four screws to secure the new power supply assembly in place. Note: Use only screws provided by Lenovo. 9. Connect the new power supply assembly cables to all drives and the system board.
  • Page 107 7. Remove the four screws 1 that secure the heat sink and fan assembly to the system board. Note: Carefully remove the four screws from the system board to avoid any possible damage. The four screws are integrated parts of the heat sink and fan assembly and they cannot be removed from the heat sink and fan assembly.

  • Page 108: Replacing The Microprocessor

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the microprocessor. CAUTION: The heat sink and microprocessor might be very hot.
  • Page 109 7. Lift the small handle 3 and open the retainer 1 to access the microprocessor 2 . Figure 20. Accessing the microprocessor 8. Lift the microprocessor straight up and out of the microprocessor socket, as shown in Figure 21 on page 104. Notes: a.
  • Page 110 d. Do not drop anything onto the microprocessor socket while it is exposed. The socket pins must be kept as clean as possible. Figure 21. Removing the microprocessor 9. Make sure that the small handle is in the raised position. 10.

  • Page 111: Replacing The Optical Drive

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the optical drive.
  • Page 112 6. Slide the new optical drive into the drive bay from the front and align the screw holes in the new optical drive with the corresponding holes in the drive bay. Then, install the two screws to secure the new optical drive in place. Figure 23.

  • Page 113: Replacing The Hard Disk Drive

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the hard disk drive.
  • Page 114 6. Slide the new hard disk drive into the hard disk drive bay and align the screw holes in the new hard disk drive with the corresponding holes in the drive bay. Then, install the four screws to secure the new hard disk drive in place. Figure 26.

  • Page 115: Replacing The Card Reader

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the card reader.

  • Page 116: Replacing The Front Audio And Usb Assembly

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the front audio and USB assembly.

  • Page 117: Replacing The System Board

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the system board.
  • Page 118 CAUTION: The heat sink and microprocessor might be very hot. Turn off the computer and wait three to five minutes to let the computer cool before opening the computer cover. To replace the system board: 1. Remove all media from the drives and turn off all attached devices and the computer.
  • Page 119 9. Remove the six screws that secure the system board. Figure 30. Removing the six screws that secure the system board 10. Carefully slide the system board so that it can be released from the mounting studs that secure the system board in place. 11.

  • Page 120: Completing The Parts Replacement

    The failing system board must be returned with a microprocessor socket cover to protect the pins during shipping and handling. To install the microprocessor socket cover: 1. Remove the microprocessor from the microprocessor socket. See “Replacing the microprocessor” on page 135. 2.
  • Page 121 Setup Utility program. See Chapter 6, “Using the Setup Utility,” on page 49. Note: In most areas of the world, Lenovo requires the return of the defective Customer Replaceable Units (CRUs). Information about this will come with the new CRUs or will come a few days after you receive the new CRUs.
  • Page 122 Hardware Maintenance Manual...

  • Page 123: Chapter 9. Replacing Frus (Machine Types: 0889, 5023, And 7844.)

    Figure 34. Front connector, control, and indicator locations 1 Optical drive eject/close button 2 Power switch 3 Hard disk drive activity indicator 4 Power indicator © Copyright Lenovo 2010 5 USB connector 6 Microphone connector 7 Headphone connector 8 USB connector...

  • Page 124: Locating Connectors And Parts On The Rear Of Your Computer

    Locating connectors and parts on the rear of your computer Figure 2 on page 84 shows the locations of the connectors and parts on the rear of your computer. Some connectors on the rear of your computer are color-coded to help you determine where to connect the cables on your computer.

  • Page 125: Locating Components

    3 Memory modules (2) 4 System board 5 Optical drive 6 the front audio and USB assembly 7 Hard disk drive 8 Battery 9 PCI Express x16 graphics card (available in some models) Chapter 9. Replacing FRUs - Desktop computers...

  • Page 126: Locating Parts On The System Board

    Locating parts on the system board Figure 37 shows the locations of the parts on the system board. Figure 37. System board part locations 1 Microprocessor 2 Microprocessor fan connector 3 Memory slots (2) 4 24-pin power connector 5 Front panel connector 6 SATA connectors (3) 7 Clear CMOS (Complementary Metal Oxide Semiconductor) /Recovery jumper...

  • Page 127: Locating Internal Drives

    2 Bay 2 - Slim card reader drive bay (with a slim card reader installed in some models) 3 Bay 3 - SATA hard disk drive bay (with a 3.5-inch SATA hard disk drive installed) Chapter 9. Replacing FRUs - Desktop computers...

  • Page 128: Removing The Computer Cover

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to remove the computer cover.

  • Page 129: Removing And Reinstalling The Front Bezel

    1. Remove all media from the drives and turn off all attached devices and the computer. Then, disconnect all power cords from electrical outlets and disconnect all cables that are connected to the computer. 2. Remove the computer cover. See “Removing the computer cover” on page 122. Chapter 9. Replacing FRUs - Desktop computers...
  • Page 130 3. Remove the front bezel by releasing the three plastic tabs on the top and pivoting the front bezel forward. Carefully lay the front bezel to the side without disconnecting the power switch and light-emitting diode (LED) assembly cable. Figure 40. Removing the front bezel 4.

  • Page 131: Accessing The System Board Components And Drives

    3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 123. 4. Pivot the drive bay assembly upward to access all the internal drives, cables, and other components. Figure 42. Pivoting the drive bay assembly upward Chapter 9. Replacing FRUs - Desktop computers...

  • Page 132: Installing Or Replacing A Pci Card

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a PCI card.
  • Page 133 If you are installing a PCI card, remove the appropriate PCI card slot cover. See “Locating parts on the system board” on page 120 to identify the types of PCI card slots. 4. Remove the new PCI card from its static-protective package. Chapter 9. Replacing FRUs - Desktop computers...

  • Page 134: Installing Or Replacing A Memory Module

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to install or replace a memory module.
  • Page 135 If you are installing a memory module, open the retaining clips of the memory slot into which you want to install the memory module. Figure 47. Opening the retaining clips of the memory slot Chapter 9. Replacing FRUs - Desktop computers...

  • Page 136: Replacing The Battery

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support Your computer has a special type of memory that maintains the date, time, and configuration information for built-in features.

  • Page 137: Replacing The Heat Sink And Fan Assembly

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the heat sink and fan assembly. Chapter 9. Replacing FRUs - Desktop computers...
  • Page 138 CAUTION: The heat sink and fan assembly might be very hot. Turn off the computer and wait three to five minutes to let the computer cool before removing the computer cover. To replace the heat sink and fan assembly, do the following: 1.
  • Page 139 9. Install the four screws in the following sequence to secure the new heat sink and fan assembly in place: a. Tighten screw 1 a small amount, then fully install screw 3 , and then fully install screw 1 , as shown in Figure 52. Chapter 9. Replacing FRUs - Desktop computers...
  • Page 140 b. Tighten screw 2 a small amount, then fully install screw 4 , and then fully install screw 2 , as shown in Figure 52 on page 133. 10. Connect the new heat sink and fan assembly cable to the microprocessor fan connector on the system board.

  • Page 141: Replacing The Microprocessor

    3. Remove the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 131. 4. Place the heat sink and fan assembly on its side so that the thermal grease on the bottom of it does not get in contact with anything. Chapter 9. Replacing FRUs - Desktop computers...
  • Page 142 5. Lift the small handle 3 and open the retainer 1 to access the microprocessor 2 . Figure 54. Accessing the microprocessor 6. Lift the microprocessor straight up and out of the microprocessor socket, as shown in Figure 21 on page 104. Notes: a.
  • Page 143 12. Reinstall the heat sink and fan assembly. See “Replacing the heat sink and fan assembly” on page 131. 13. To complete the replacement, go to “Completing the parts replacement” on page 157. Chapter 9. Replacing FRUs - Desktop computers...

  • Page 144: Replacing The Power Supply Assembly

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the power supply assembly.
  • Page 145 Note: You might also need to release the power supply assembly cables from some cable clips or ties that secure the cables to the chassis. Make sure that you note the cable routing before disconnecting the cables. Chapter 9. Replacing FRUs - Desktop computers...
  • Page 146 6. At the rear of the computer, remove the three screws that secure the power supply assembly. Press the release button 1 , slide the power supply assembly a little bit forward, and then remove the power supply assembly from the computer. Figure 57.
  • Page 147 Then, install the three screws to secure the new power supply assembly in place. Note: Use only screws provided by Lenovo. Figure 58. Installing the power supply assembly 9. Connect the new power supply assembly cables to all drives and to the 24-pin power connector and 4-pin power connector on the system board.

  • Page 148: Replacing The Optical Drive

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the optical drive.
  • Page 149 6. Hold the drive bay assembly and remove the two screws that secure the optical drive. Figure 60. Removing the two screws that secure the optical drive 7. Lower the drive bay assembly. See “Accessing the system board components and drives” on page 125. Chapter 9. Replacing FRUs - Desktop computers...
  • Page 150 8. Slide the optical drive out of the front of the computer. Figure 61. Removing the optical drive 9. Slide the new optical drive into the optical drive bay from the front of the computer. Figure 62. Installing the optical drive Hardware Maintenance Manual...
  • Page 151 Figure 64. Connecting a SATA optical drive 12. To complete the replacement, go to “Completing the parts replacement” on page 157. Chapter 9. Replacing FRUs - Desktop computers...

  • Page 152: Replacing The System Board

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the system board.
  • Page 153 125. 17. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 123. 18. Reinstall the computer cover. 19. Go to “Completing the parts replacement” on page 157. Chapter 9. Replacing FRUs - Desktop computers...
  • Page 154 The failing system board must be returned with a microprocessor socket cover to protect the pins during shipping and handling. To install the microprocessor socket cover: 1. Remove the microprocessor from the microprocessor socket. See “Replacing the microprocessor” on page 135. 2.

  • Page 155: Replacing The Hard Disk Drive

    3. Remove the front bezel. See “Removing and reinstalling the front bezel” on page 123. 4. Note the locations of the four screws 1 that secure the hard disk drive. Then, pivot the drive bay assembly upward. Figure 68. Pivoting the drive bay assembly upward Chapter 9. Replacing FRUs - Desktop computers...
  • Page 156 5. Hold the hard disk drive from one side of the drive bay assembly and remove the four screws that secure the hard disk drive from the other side. Then, remove the hard disk drive from the drive bay assembly and disconnect the signal cable and the power cable from the rear of the hard disk drive to completely remove it from the chassis.
  • Page 157 Figure 71. Installing the hard disk drive 8. To complete the replacement, go to “Completing the parts replacement” on page 157. Chapter 9. Replacing FRUs - Desktop computers...

  • Page 158: Replacing The Card Reader

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the card reader.

  • Page 159: Replacing The Front Audio And Usb Assembly

    7. Lower the drive bay assembly. See “Accessing the system board components and drives” on page 125. 8. Remove the screw that secures the front audio and USB assembly. Then, remove the front audio and USB assembly from the chassis. Chapter 9. Replacing FRUs - Desktop computers...

  • Page 160: Replacing The Front Fan Assembly

    “Important safety information” in the ThinkCentre Safety and Warranty Guide that came with your computer. To obtain a copy of the ThinkCentre Safety and Warranty Guide, go to: http://www.lenovo.com/support This section provides instructions on how to replace the front fan assembly.
  • Page 161 8. The front fan assembly is attached to the chassis by four rubber mounts 1 . Remove the front fan assembly by cutting the rubber mounts and lifting the front fan assembly out of the chassis. Figure 74. Removing the front fan assembly Chapter 9. Replacing FRUs - Desktop computers...
  • Page 162 9. Install the new front fan assembly by aligning the new rubber mounts that came with the new front fan assembly with the corresponding holes in the chassis, and then push the rubber mounts through the holes. Then, carefully pull on the tips of the rubber mounts from the bottom side until the new front fan assembly is secured in place.

  • Page 163: Completing The Parts Replacement

    3. Lower the drive bay assembly. See “Accessing the system board components and drives” on page 125. 4. Reinstall the front bezel. See “Removing and reinstalling the front bezel” on page 123. Chapter 9. Replacing FRUs - Desktop computers...
  • Page 164 Setup Utility program. See Chapter 6, “Using the Setup Utility,” on page 49. Note: In most areas of the world, Lenovo requires the return of the defective Customer Replaceable Units (CRUs). Information about this will come with the new CRUs or will come a few days after you receive the new CRUs.

  • Page 165: Chapter 10. Fru Lists

    Microprocessor, Core 2 Duo E7500 Processor 2.93GHz 1066MHz FSB 3M L2 R-0 Stepping 65W (models A4B A5A A5Q A5T A5V A5K A5R C5A C5Q C5T A5P) Microprocessor, Core 2 Duo E7400 Processor 2.8GHz 1066MHz FSB 3M L2 R-0 VT Stepping 65W (models) © Copyright Lenovo 2010 7099 FRUs FRU # 46R8640...
  • Page 166 Item Microprocessor, Core 2 Duo E6600 Processor 3.06GHz 1066MHz FSB 2M L2 R-0 Stepping 65W (models BGH B4M B8U B8F B9U B9F) Microprocessor, Core 2 Duo E6500 Processor 2.93GHz 1066MHz FSB 2M L2 R-0 Stepping 65W (models BMJ BNJ BPJ B6U B6F B7U B7F BCS BCP BCL BCD BCY) Microprocessor, Core 2 Duo E6300 Processor 2.8GHz 1066MHz FSB 2M L2 R-0 Stepping 65W (models) Microprocessor, E5500 Processor 2.8GHz 800Mhz FSB 2M, L2 R-0 Stepping 65W...
  • Page 167 Item Hard disk drive, SATA 250GB 7200RPM / 3Gb / 8M (models A8A A8Q A8T A8V A8K A8R A1U A1F A1S A1G D5J) Hard disk drive, SATA 250GB 7200RPM / 3Gb / 8M (models A8A A8Q A8T A8V A8K A8R A1U A1F A1S A1G D5J) Hard disk drive, SATA 320GB 7200 RPM / 3Gb / 8M (models A4B A7S A7Y A7A A7Q A7T A7V A7K A7R B6T B7S B7Y B7G B7A B7T B8G A5A A5Q A5T A5V A5K A5R A3U A3F A3S C1B C1V C2U C2F C2S C2B C3B D6B D7S D7D D7Y C7A C7T...
  • Page 168 Thailand (models) Turkish (models) Turkish (models) UK English (models) US Euro (models) Slovenian (models) Arabic(New)(models) Lithuanian (models) Estonian (models) 7099 Keyboards (Lenovo Fingerprint Reader USB) US English (models) Arabic (models) Hardware Maintenance Manual FRU # 54Y8305 54Y8306 54Y8307 54Y8308 54Y8309...
  • Page 169 7099 Keyboards (Lenovo Fingerprint Reader USB) Arabic/French (models) Belgium French (models) Belgium English (models) Brazilian Portuguese (models) Bulgarian (models) Chinese/US (models) Czech (ABB) (models) Danish (models) Dutch (models) French (models) French Canadian (models) French Canadian (models) German (models) Greek (models)
  • Page 170 7099 Keyboards (Preferred Pro USB Keyboard) US English (models) Arabic (models) Arabic/French (models) Belgium French (models) Belgium English (models) Brazilian Portuguese (models) Bulgarian (models) Chinese/US (models) Czech (ABB) (models) Danish (models) Dutch (models) French (models) French Canadian (models) French Canadian (models) German (models) Greek (models) Greek/US (models)
  • Page 171 7099 Keyboards (Preferred Pro USB Keyboard) Arabic(New)(models) Lithuanian (models) Optical Wheel Mouse (400DPI, USB) (models A4B A6A A6Q A6T A6V A6K A6R A7S A7Y A7A A7Q A7T A7V A7K A7R A8A A8Q A8T A8V A8K A8R B6T B7S B7Y B7G B7A B7T B8G B9G A5A A5Q A5T A5V A5K A5R A1U A1F A1S A1G C1B C1V C2U C2F C2S C2B C3B D6B D7S D7D D7Y C7A C7T C8A C8T C9A C9T D1A D1T D2A D2T D5J C4Q C5A C5Q C5T C6A C6Q C6T D3V D4V D7P A7P P1P A5P)
  • Page 172 7099 Power Cords (Secondary) Power cord - US (models A6A A7S A7A A8A B7A A1U A1F C2U C2F C2S D7S D7D C7A C8A C9A D1A D2A C5A C6A) Power cord - China (models) Power cord - Japan (models D5J) Power cord - Brazil (models D7P A7P P1P A5P) Power cord - Brazil (models A7Y B7Y D7Y) Power cord - LA High Volt (APU) (models) Power cord - Australia / New Zealand (models)
  • Page 173 7099 Windows 7 Professional 32 Recovery Discs Arabic localized (models B7G B8G B9G) Hebrew (models B7G B8G B9G) Traditional Chinese (models A6V A7V A5V C1V D4V) Hong Kong (models A4B C2B C3B D6B) Portuguese (models B7G B8G B9G A1G A7P A5P ) C&L Core We(EN FR GR IT NL SP) (models B7G B8G B9G) C&L Nordics (EN DK FI NO SV) (models B7G B8G B9G) 7099 Windows 7 Home Basic 32 Recovery Discs...

  • Page 174: Machine Type 7844

    7099 Windows 7 Professional 64 Recovery Discs French (models) Spanish (models) Italian (models) Hong Kong (models) C&L HongKong Chinese (models) Japanese (models) C&L Nordics (EN DK FI NO SV) (models) C&L CORE WE (EN FR GR IT NL SP) (models) Machine type 7844 Item # Microprocessor, Core 2 Duo E8600 Processor 3.33GHz 1333MHz FSB 6M L2 E-0...
  • Page 175 Item # Microprocessor, Core 2 Duo E6300 Processor 2.8GHz 1066MHz FSB 2M L2 R-0 Stepping 65W (models) Microprocessor, E5500 Processor 2.8GHz 800Mhz FSB 2M, L2 R-0 Stepping 65W (models C1G E7B D2B D2V D9V) Microprocessor, E5400 Processor 2.7GHz 800MHz FSB 2M L2 R-0 VT Stepping 65W (models B7A B7Q B7T B7V B7K B7R B8S B8Y B8A B8Q B8T B8V B8K B8R A6M C6S C6Y C7S C7Y D1S D1Y ) Microprocessor, E5300 Processor 2.6GHz 800MHz FSB 2M L2 R-0 VT Stepping...
  • Page 176 ODD blank cover (all models) ODD blank cover (all models) 7844 Keyboards (Lenovo Preferred Pro USB - without hub) US English (models B7A B7Q B7R B8A B8Q B8R B9A B9Q B9R B9R C1G C2G C3G A5M A6M A7M A8M A9M B1M B2M B4A B4Q B4R A1U A1G D4U D5A D6A)
  • Page 177 7844 Keyboards (Lenovo Preferred Pro USB - without hub) Brazilian Portuguese (models) Bulgarian (models C1G C2G C3G A1G) Chinese/US (models E7B D2B D2V D3B D4B D7V D8V D9V E1V E2V E3V) Czech (ABB) (models C1G C2G C3G A1G) Danish (models C1G C2G C3G A1G)
  • Page 178 7844 Keyboards (Lenovo Fingerprint Reader USB) US English (models) Arabic (models) Arabic/French (models) Belgium French (models) Belgium English (models) Brazilian Portuguese (models) Bulgarian (models) Chinese/US (models) Czech (ABB) (models) Danish (models) Dutch (models) French (models) French Canadian (models) French Canadian (models)
  • Page 179 7844 Keyboards (Slim USB) US English (models) Arabic (models) Arabic/French (models) Belgium French (models) Belgium English (models) Brazilian Portuguese (models) Bulgarian (models) Traditional Chinese (models) Czech (ABB) (models) Danish (models) Dutch (models) French (models) French Canadian (models) French Canadian (models) German (models) Greek (models) Greek/US (models)
  • Page 180 7844 Keyboards (Slim USB) Arabic(New)(models) Lithuanian (models) Estonian (models) Optical Wheel Mouse (400DPI, USB) (models A4B A6A A6Q A6T A6V A6K A6R A7S A7Y A7A A7Q A7T A7V A7K A7R A8A A8Q A8T A8V A8K A8R B6T B7S B7Y B7G B7A B7T B8G B9G A5A A5Q A5T A5V A5K A5R A1U A1F A1S A1G C1B C1V C2U C2F C2S C2B C3B D6B D7S D7D D7Y C7A C7T C8A C8T C9A C9T D1A D1T D2A D2T D5J C4Q C5A C5Q C5T C6A C6Q C6T D3V D4V D7P A7P P1P A5P)
  • Page 181 7844 Power Cords (Secondary) Power cord - US (models B7A B8A B9A B4A A1U A1F D4U D4F D5A D6A) Power cord - China (models) Power cord - Japan (models B3J B4J B5J B6J D5J E4J E5J E6J E3J) Power cord - Brazil (models) Power cord - Brazil (models B8Y B4Y C6Y C7Y C8Y C9Y D1Y) Power cord - LA High Volt (APU) (models) Power cord - Australia / New Zealand (models A5M A6M A7M A8M A9M B1M B2M)
  • Page 182 7844 Windows 7 Professional 32 Recovery Discs Serbian-Latin (models C1G C2G C3G A1G) Slovakian (models C1G C2G C3G A1G) Arabic localized (models C1G C2G C3G A1G) Hebrew (models C1G C2G C3G A1G) Traditional Chinese (models D2V D8V) Hong Kong (models E7B D2B D3B D4B) Portuguese (models C1G C2G C3G A1G) C&L CORE WE (EN FR GR IT NL SP) (models C1G C2G C3G A1G) C&L Nordics (EN DK FI NO SV) (models C1G C2G C3G A1G)
  • Page 183 7844 Windows 7 Professional 64 Recovery Discs US English (models) French (models) Spanish (models) Italian (models) Hong Kong (models) C&L HongKong Chinese (models) Japanese (models) C&L Nordics (EN DK FI NO SV) (models) C&L CORE WE (EN FR GR IT NL SP) (models) number CRU tier Chapter 10.
  • Page 184 Hardware Maintenance Manual...

  • Page 185: Chapter 11. Additional Service Information

    – Start the Setup Utility program. – See BIOS Revision Level on the Main setup screen. v Sources for obtaining the latest level BIOS available 1. Lenovo support web site: http://www.lenovo.com/support/ 2. Lenovo Customer Support Center 3. Levels 1 and 2 Support To update (flash) the BIOS, see “Updating (flashing) the BIOS from a disc”...

  • Page 186: Updating (Flashing) The Bios From A Disc

    Updating (flashing) the BIOS from your operating system Note: Because Lenovo makes constant improvements to its Web sites, the Web page contents are subject to change without notice, including the contents referenced in the following procedure.

  • Page 187: Recovering From A Post And Bios Update Failure

    Recovering from a POST and BIOS update failure If the power to your computer is interrupted while the POST and BIOS is being updated, your computer might not restart correctly. If this happens, perform the following procedure, which is commonly called Boot-block Recovery. 1.
  • Page 188 v Wake on LAN: If the computer has a properly configured token-ring or Ethernet LAN adapter card that is Wake on LAN-enabled and there is remote network management software, you can use the Wake on LAN feature. When you set Wake on LAN to Enabled, the computer will turn on when it receives a specific signal from another computer on the local area network (LAN).

  • Page 189: Appendix. Notices

    Web sites. The materials at those Web sites are not part of the materials for this Lenovo product, and use of those Web sites is at your own risk.

  • Page 190: Television Output Notice

    Macrovision Corporation. Reverse engineering or disassembly is prohibited. European conformance CE mark Trademarks The following terms are trademarks of Lenovo in the United States, other countries, or both: Lenovo Rescue and Recovery The Lenovo logo...
  • Page 192 Part Number: 89Y9149 Printed in USA (1P) P/N: 89Y9149...

This manual is also suitable for:

Thinkcentre 0864Thinkcentre 7846Thinkcentre 0889Thinkcentre 5023Thinkcentre 7099Thinkcentre 7844

Table of Contents