Advertisement
Quick Links
Bianco RainsaverMK4E Installation and Operating Instructions
Bianco RainsaverMK4E is WaterMark Level 1 approved to ATS5200.477:2006 Certificate No.
23022 and incorporates internal dual check valve back flow prevention for the mains water.
INSTRS110110 rev 6 01/03/15
Page 1
Advertisement
Related Manuals for Watermark rainsaver Bianco RainsaverMK4E
Summary of Contents for Watermark rainsaver Bianco RainsaverMK4E
- Page 1 Bianco RainsaverMK4E Installation and Operating Instructions Bianco RainsaverMK4E is WaterMark Level 1 approved to ATS5200.477:2006 Certificate No. 23022 and incorporates internal dual check valve back flow prevention for the mains water. INSTRS110110 rev 6 01/03/15 Page 1...
- Page 2 Bianco Rainsaver MK4E Installation and Operating Instructions 1. Introduction: The Rainsaver MK4E is an Automatic Rainwater / Mains Water Changeover Device designed to provide automatic mains back up for Pressure Pump supply systems. The Bianco Rainsaver MK4E is designed to be installed in conjunction with a DAB or Bianco surface mounted or submersible Pressure Pump supply system that is fitted with a FLOAT SWITCH (except for the DAB DIVERTRON) as well as an independent PRESSURE AND FLOW CONTROLLER with LOSS OF PRIME PROTECTION and AUTOMATIC RE-START.
- Page 3 4.2 RainsaverMK4E installation. The RainsaverMK4E must be mounted in the horizontal position, and the RainsaverMK4E power socket to accept the pump power lead must hang in the down position. The RainsaverMK4E can be Wall mounted or Pump Mounted i.e. mounted directly onto a pressure pump outlet.
- Page 4 4.22 Pump Mounting: RainsaverMK4E can be mounted directly onto the outlet of the pump with the adaptor supplied. If another size threaded port is found on the pump or controller outlet use quality standard plastic threaded pipe fittings to adapt. Pump Mounting Instructions: Remove wall mounting bracket by unscrewing the lower (Pump Inlet) union nut using the plastic spanner provided.
- Page 5 4.4 Filtration and Water Quality The Bianco Rainsaver MK4E is designed to operate on clean rainwater and clean mains water supply, and as such, the rainwater tank should be fitted with an inlet strainer, preferably shaded type to reduce algae, and a suitable first flush device. White International strongly recommends the use of a strainer or filter upstream with easy access for period cleaning from both the rainwater and mains inlet connections of the Bianco Rainsaver MK4E.
- Page 6 BSP fitting, or removed if using a ¾” BSPT fitting. Use a suitable flexible reinforced hose with ¾” BSP or BSPT MALE THREAD to connect a WATERMARK approved pressure tank such as a GWS Energy Saver to your RainsaverMK4E. Carefully follow the manufacturer’s instructions regarding pressurization of your pressure tank.
- Page 7 5. Sound Emissions. The RainsaverMK4E is virtually silent but may emit noises associated with the flow of water through the unit. In any case, the pump, which is connected to the RainsaverMK4E, may emit sound levels, which may inconvenience you or your neighbours, or may operate during normal sleeping hours, which may be prohibited by local government regulations.
- Page 8 8. Pumps Pumps and pump controllers must be accessible and fitted with barrel unions for service and maintenance. It is recommended that all surface mounted pumps be protected from the elements with a suitable pump cover. Submersible pump accessories such as pump stands, high inlets, floating suction hose kits assist in the pumping cleaner water that is found at higher levels in the rainwater tank.
- Page 9 Installation Dimensions INSTRS110110 rev 6 01/03/15 Page 9...
- Page 10 Typical Installations. RAINSAVER MK4E RAINSAVER MK4E DAB or BIANCO surface mounted pumps. INSTRS110110 rev 6 01/03/15 Page 10...
- Page 11 RAINSAVER MK4E RAINSAVER MK4E TESLA DIVERxxxMPCX Submersible Pump INSTRS110110 rev 6 01/03/15 Page 11...
- Page 12 RAINSAVER MK4E RAINSAVER MK4E BIANCO JH8003PMPCX or B42A Submersible Pumps INSTRS110110 rev 6 01/03/15 Page 12...
- Page 13 RAINSAVER MK4E RAINSAVER MK4E DAB DIVERTRON1200 Submersible Pump INSTRS110110 rev 6 01/03/15 Page 13...
- Page 14 Accessories Pump Cover protects pump from the elements. Pump stand for submersible pumps lifts pump up to pump cleaner water. DAB Divertron X conversion kit allows pumping from higher level and connection to floating suction kits to pump cleaner water higher in the tank. INSTRS110110 rev 6 01/03/15 Page 14...
- Page 15 Accessories Tesla DiverDry conversion kit allows pumping from higher level and connection to floating suction kits to pump cleaner water. Floating suction hose kits allow pumping from cleaner water higher in the tank. Float switch for bladder tank. Piggy back float switch option for Divertron. INSTRS110110 rev 6 01/03/15 Page 15...
- Page 16 INSTRS110110 rev 6 01/03/15 Page 16...