Related Manuals for 909 LS15CS
Summary of Contents for 909 LS15CS
- Page 1 INSTRUCTION MANUAL LS15CS 15 AMP DUAL LASER CIRCULAR SAW WITH MAGNESIUM Black Magenta Code: LS15CS Cyan Yellow Date: 100326 Edition: 2 Op: DCR...
-
Page 2: Table Of Contents
CONTENTS Warranty Power Tools Warranty Introduction For full details please visit us at www.909.com Environmental protection Description of symbols Specifications General safety rules Additional safety rules for laser lights Additional safety rules for circular saws Accessories Unpacking Assembly Know your product... -
Page 3: Environmental Protection
Tool is listed by Underwriters Laboratories special care to heed the Cautions and Warnings. and listed to Canadian Standards by Underwriters Laboratories Your 909 power tool has many features that will make E205892 your job faster and easier. Safety, performance, and Specifications... -
Page 4: General Safety Rules
General safety rules 5. When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. WARNING Read and understand all instructions. Failure These cords are rated for outdoor use and reduce to follow all instructions listed below, may result in electric the risk of electric shock. -
Page 5: Additional Safety Rules For Laser Lights
3. Do not use tool if switch does not turn it on or off. Safety rules for laser lights Any tool that cannot be controlled with the switch is dangerous and must be repaired. AVERTISSEMENT CAUTION 4. Disconnect the plug from the power source before RAYONNEMENT LASER –... - Page 6 • Check lower guard for proper closing before each use. • Always use blades of the correct size and shape Do not operate the saw if the lower guard does not move (diamond vs. round) arbour holes. Blades that do freely and close instantly.
-
Page 7: Accessories
Secure small pieces of wood firmly before working. Never hold them in your hand. Due to modern mass production techniques, it is unlikely that your 909 Power Tool is faulty or that a part is missing. • Never slow the blade down with your hands or by If you find anything wrong, do not operate the tool until the applying pressure to the side of the blade. -
Page 8: Know Your Product
Know your product 1. Dual Laser light assembly 2. Dual Laser light on/off button 3. Dual Laser light aperture 4. Trigger switch 5. Lock-off button 6. Motor housing 7. Main handle 8. Front handle 9. Bevel adjustment knob 10. Bevel scale 11. -
Page 9: Overview
You have purchased a 15 Amp Magnesium Circular Saw The correct blade depth setting for all cuts should not be with the 909 laser line generator system. more than 1/4” (6.35mm) below the material being cut. Please refer to the safety instructions given earlier in this Allowing more depth will increase the chance of kickback manual for important instructions regarding the use of the laser. -
Page 10: Switching On And Off
6. Start the motor by depressing Note. Always make a trial cut in a scrap piece of material the lock-off button (5) and along a guideline to determine how much you should offset squeezing the trigger the blade from the guideline to make an accurate cut. switch (4). -
Page 11: Using The Parallel Fence
4. With the blade just clearing the work piece, start the 3. Adjust the parallel fence to the motor by depressing the lock-off button (5) and squeezing required width and secure it in the trigger switch (4). position with the parallel fence locking knob (11). -
Page 12: Changing The Blade
6. Start the motor by depressing the lock-off button (5) and 6. Remove the saw blade from the inner flange squeezing the trigger switch (4). and pull it out (Fig. S) 7. Always let the blade reach full speed (approximately 7. -
Page 13: Maintenance
Maintenance CAUTION. Do not use cleaning agents to clean the plastic parts of the tool. A mild detergent on a damp cloth is WARNING. Always ensure that the tool is switched off and recommended. Water must never come into contact the plug is removed from the power point before making any with the tool.
Need help?
Do you have a question about the LS15CS and is the answer not in the manual?
Questions and answers