Subscribe to Our Youtube Channel
Related Manuals for 909 LS1200
Summary of Contents for 909 LS1200
- Page 1 INSTRUCTION MANUAL LS1200 / TCAT235 2000W 235MM (9 1/4”) MAGNESIUM BASE CIRCULAR SAW / 1200W 165MM (6 1/2”) LASER GUIDED CIRCULAR SAW...
-
Page 2: Table Of Contents
CONTENTS Warranty Power Tools Warranty For full details please visit us at www.909.com Introduction Environmental protection Description of symbols Specifications General safety rules Additional safety rules for laser lights Additional safety rules for circular saws Accessories Unpacking Assembly Know your product... -
Page 3: Environmental Protection
Manual before using your new 909 Power Tool. Take Double insulated for additional protection. special care to heed the Cautions and Warnings. Your 909 power tool has many features that will make Conforms to relevant standards your job faster and easier. Safety, performance, and for electromagnetic compatibility. -
Page 4: General Safety Rules
suitable for outdoor use reduces the risk of electric shock. General safety rules f) To reduce the risk of electric shock, the manufacturer WARNING. Read all safety warnings and all instructions. recommends the use of a residual current device Failure to follow the warnings and instructions may result in with a rated residual current of 30mA or less at electric shock, fire and/or serious injury. -
Page 5: Additional Safety Rules For Laser Lights
4) Power tool use and care i) Children should be supervised to ensure that they do not play with the appliance. a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will 5) Service do the job better and safer at the rate for which it was a) Have your power tool serviced by a qualified repair... -
Page 6: Additional Safety Rules For Circular Saws
CAUTION. Use of controls or adjustments or performance h. Never use damaged or incorrect blade washers or of procedures other than those specified herein may result bolt. The blade washers and bolt were specially designed in hazardous radiation exposure. for your saw, for optimum performance and safety of operation. -
Page 7: Accessories
Due to modern mass production techniques, it is unlikely sluggishly due to damaged parts, gummy deposits, or a that your 909 Power Tool is faulty or that a part is missing. build-up of debris. If you find anything wrong, do not operate the tool until the c. -
Page 8: Know Your Product
Know your product TCAT235 1. On/Off Trigger switch 2. Lock-off button 3. Motor housing 4. Main handle 5. Front handle 6. Bevel adjustment lever 7. Bevel scale 8. Parallel fence locking knob 9. Parallel fence 10. Blade guard lever 11. Lower blade guard 12. -
Page 9: Know Your Product
Know your product LS1200 1. Laser light assembly 2. Laser light on/off button 3. Laser light aperture 4. On/Off Trigger switch 5. Lock-off button 6. Motor housing 7. Main handle 8. Front handle 9. Bevel adjustment knob 10. Bevel scale 11. -
Page 10: Overview
Overview Note. Always use the correct blade depth setting. The correct blade depth setting for all cuts should not be You have purchased a 1200W or 2000W Circular Saw. more than (6.35mm) 1/4” below the material being cut. Please refer to the safety instructions given earlier in this Allowing more depth will increase the chance of kickback manual for important instructions. -
Page 11: Switching On And Off
6. Start the motor by depressing Note. Always make a trial cut in a scrap piece of material the lock-off button and along a guideline to determine how much you should offset squeezing theOn/Off trigger the blade from the guideline to make an accurate cut. switch. -
Page 12: Using The Parallel Fence
Using the Laser system (Applicable only on 7. Once the base plate is flat against the work piece, proceed cutting in a forward direction to the end of the LS1200 Circular Saw) the cut. WARNING. Before proceeding to use the laser line system, 8. -
Page 13: Changing The Blade
6. Start the motor by depressing the lock-off button (5) and 6. Remove the saw blade squeezing the On/Off trigger switch. from the inner flange and pull it out (Fig. S) 7. Always let the blade reach full speed (approximately 2 seconds) before you begin to cut into the work piece. -
Page 14: Maintenance
Maintenance CAUTION. Do not use cleaning agents to clean the plastic parts of the tool. A mild detergent on a damp cloth is WARNING. Always ensure that the tool is switched off and recommended. Water must never come into contact the plug is removed from the power point before making any with the tool.
Need help?
Do you have a question about the LS1200 and is the answer not in the manual?
Questions and answers