Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for 909 PS26W
Summary of Contents for 909 PS26W
- Page 1 INSTRUCTION MANUAL PS26W 26cc POL E T RIMMING...
-
Page 2: Table Of Contents
CONTENTS Warranty Warranty Power Tools Introduction For full details please visit us at www.909.com Environmental protection Specifications Description of symbols General safety instructions Additional safety instructions for the inbuilt battery pack Additional safety instructions for the charger Additional safety rules for pole trimmers... -
Page 3: Environmental Protection
Manual before using your new 909 pole saw. Take special care to heed the Cautions and Warnings. Read these instructions for use carefully. Your 909 pole saw has many features that will make your job faster and easier. Safety, performance, and Wear safety footwear. -
Page 4: General Safety Instructions
General safety instructions for handling • Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of power tools electric shock. WARNING: Read all safety warnings and all instructions. • Do not abuse the cord. Never use the cord for carrying, Failure to follow the warnings and instructions may result in pulling or unplugging the power tool. -
Page 5: Additional Safety Instructions For The Inbuilt Battery Pack
5). Use and care of the battery pack • Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving • Ensure the key switch is in the OFF position and the parts. Loose clothes, jewellery or long hair can be caught key is removed before connecting or disconnecting the in moving parts. -
Page 6: Additional Safety Instructions For The Charger
• Never attempt to open the inbuilt battery pack for any • Do not use an extension cord unless it is absolutely reason. If the plastic housing of the battery pack breaks necessary. The use of an improper extension cord could open or cracks, immediately discontinue its use and do cause the risk of fire, electric shock or electrocution. -
Page 7: General Notes
Always wear gloves when handling the pole saw chain. Due to modern mass production techniques, it is unlikely Danger! that your 909 Power Tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the BEWARE oF KICKBACK! parts have been replaced or the fault has been rectified. -
Page 8: Know Your Product
Know your product 1. Motor housing 25. Air filter cover 2. On/Off switch 26. Primer 3. Oil Mix Container 27. Chain drive cover 4. Throttle trigger 28. Spark plug/spark plug cover 5. Safety lever 29. Spanner 6. Main handle 30. Chain drive sprocket 7. -
Page 9: Assembly
Assembly This product is partially assembled. Prior to use, it is necessary to assemble/fit the upper shaft (9), lower shaft (10), J handle (7), chain (17) and chain bar (12). Fitting the chain and chain bar 1. Remove the chain drive cover nut (20) with the spanner supplied (29) and remove the chain drive cover (27). -
Page 10: Adding Chain Oil
Connecting the J handle to the upper shaft the upper shaft (9). Rotate the lower shaft until the pin locates positively into the hole in the upper shaft. 1. Lay the pole saw upper Note. When rotating the shaft the middle drive shaft needs shaft down so that the petrol to engage so it may require up to a full turn to engage both tank is resting on a secure... -
Page 11: Charging The Internal Battery
Setting the oil adjustment screw charger is connected and turned on. Note, the indicator will remain on all the time the charger is connected and The pole saw has an adjustment to vary the oil flow to the turned on. chain. -
Page 12: Filling The Tank
Filling the tank Do not store pre-mixed fuel. Starting the pole saw WARNING. Always shut off the engine before fuelling. Never add fuel to a machine with a running or hot engine. Choke control Move at least 10m away from the refuelling site before Start position starting engine. -
Page 13: Warm Start
5. Check the ignition On / Off 8. To engage the chain drive on the pole saw increase the switch is on. (I pressed speed of the motor. down) Pull the recoil starter To disengage the chain drive, release pressure on the until you hear the engine throttle trigger (4). -
Page 14: Stopping The Pole Saw
Stopping the pole saw Changing of the saw chain WARNING: 1. Release pressure to the Note: Always make sure the engine is turned off throttle trigger (4) and allow when making any adjustments to the chain and bar. the engine to idle for a few Note: The saw chain is full of sharp edges. -
Page 15: Working With The Pole Saw
Working with the pole saw Chain sharpening and maintenance WARNING. Do not work with an angle higher than 60°. The pole saw Note: Always make sure the engine is turned off will work under higher degrees, but there is the danger of before making any adjustments or maintenance procedures. -
Page 16: First Time User
CAUTIoN. Water must never come into contact with it yourself. Contact 909 Customer Support or have the unit the pole saw. repaired by a professional.
Need help?
Do you have a question about the PS26W and is the answer not in the manual?
Questions and answers
WhaT IS THE CHARGER SPECIFICATIONS FOR AUSTRALIA
The charger specifications for the 909 PS26W in Australia are:
- Charge time: 3-5 hours
- Do not leave the battery on charge for longer than 24 hours
- Only use the charger supplied with the pole saw
- Insert the Plug Pack Charger into a standard 240V power point
This answer is automatically generated