La Crosse Technology WS-8025AL Instruction Manual page 7

OK Oklahoma TX Texas (cont.)
17K Boise City DFW Dallas/Ft. Worth
LAW Lawton ELP El Paso
OKC Oklahoma City HOU Houston
TUL Tulsa LRD Laredo
OR Oregon ODO Odessa
BNO Burns SAT San Antonio
EUG Eugene UT Utah
MFR Medford SAL Saline
PDX Portland SGU St. George
SLE Salem SLC Salt Lake City
PA Pennsylvania TSN Thompson
CXY Harrisburg VA Virginia
PHL Philadelphia DON Vienna
PIT Pittsburgh LYH Lynchburg
SCR Scranton ORF Norfolk
PR Puerto Rico RIC Richmond
SJU San Juan ROA Roanoke
RI Rhode Island VT Vermont
PVD Providence BTV Burlington
SC South Carolina MPR Montpelier
CHS Charleston WA Washington
CUB Columbia ABE Aberdeen
GMU Greenville ALW Walla Walla
SD South Dakota KTF Kettle Falls
FSD Sioux Falls MVN Mt. Vernon
PIR Pierre OLM Olympia
RAP Rapid City SEA Seattle
TN Tennessee SFF Spokane
BNA Nashville TON Tonasket
CHA Chattanooga YKM Yakima
DKX Knoxville WI Wisconsin
MEM Memphis AUW Wausau
TX Texas GRB Green Bay
ABI Abilene LSE La Crosse
AMA Amarillo MSN Madison
AUS Austin MWC Milwaukee
BRO Brownsville SSQ Spooner
GB
P.10
WV West Virginia
CRW Charleston
HLG Wheeling
WY Wyoming
BYG Buffalo
CPR Casper
CYS Cheyenne
LAA Little America
WYE West Yellowstone
E. Time Zone and Daylight Saving Time Settings
F. Weather measurement units (˚F/˚C, inHg/hPa)
Canada City Listing
Code City Code City
EDM Edmonton YEL Yellowknife
ALB Calgary OTT Ottawa
VAN Vancouver SUD Sudbury
WIN Winnipeg THU Thunder Bay
FRE Fredericton TOR Toronto
HAL Halifax
Mexico City Listings
Code City Code City
CHH Chihuahua MEX Mexico City
DUR Durango GUA Guadalupe
1. Press and hold the " SET " button for 1 second.
2. Press and release the " SET " button 9 times.
3. The time zone will now flash based on the city selected.
4. Press and release the "+"or "-" button to adjust to the correct time zone.
5. Press and release the " SET " button to advance to the Daylight Saving Time setting.
6. "dst ON" will now flash.
7. Press and release the "+" or "-" button to select DST 1 (recognizes Daylight Saving
Time change) or DST 0 (does not change with Daylight Saving Time).
Note : Some locations (Arizona and parts of Indiana) do not follow Daylight Saving Time.
8. Press and release the " SET " button to advance to the weather measurement units
settings (skip steps 1 and 2 in section E if continuing).
1. Press and hold the " SET " button for 1 second.
2. Press and release the " SET " button 11 times.
3. The selected temperature units will now flash (˚F default/factory setting).
4. Press and release the "+"or "-" button to select ˚F (Fahrenheit) or ˚C (Celsius).
5. Press and release the " SET " button to advance to the barometric air pressure units
setting.
6. The selected air pressure units will now flash (inHg default/factory setting).
7. Press and release the "+"or "-" button to select inHg (inches of Mercury) or hPa
(hectopascal or millibars).
8. Press and release the " SET " button to advance to the barometric air pressure calibration
setting.
9. The air pressure reading will now flash (29.91 inHg, 1012.8 hPa as default).
10. Press and release the "+"or "-" button to adjust to the correct relative air pressure
based on local reports.
11. Press and release the " SET " button to advance to the forecast sensitivity setting.
Note : Barometric air pressure is usually reported as "relative air pressure". This reading is
based on the combination of absolute air pressure and altitude. In general, an increase in
altitude will result in a decrease in air pressure. Relative air pressure will make readings in
nearby locations relative to each other to allow for proper forecasting. The absolute air
pressure reading in the Weather Center cannot be calibrated, only the relative air pressure.
Code City
CHT Charlotte Town
MON Montreal
QUE Quebec
REG Regina
WHI Whitehorse
Code City
HER Hermosillo
GB
P.11