Bush DLED50UHDHDRSB Instruction Manual page 42

Advanced features
Getting the most from your TV
The TV supports 802.11 a, b, g & n type modems. It is
highly recommended that you should use the IEEE
802.11n communication protocol in order to avoid any
possible problems while watching videos.
You must change your modem's SSID when there are any
other modems around with the same SSID. You can encounter
connection problems otherwise. Use a wired connection if you
experience problems with a wireless connection.
Configuring Wireless Device Settings
To configure wireless connection settings go to the
Settings>Network menu.
Network Type
Set Network Type as Wireless Device to start connection
process.
Scan Wireless Networks
Highlight Scan Wireless Networks option and press OK
to start a search for available wireless networks. All found
networks will be listed. Highlight your desired network
from the list and press OK to connect. A network with
hidden SSID can not be detected by other devices. If you
want to connect to a network with hidden SSID, scroll
down the list of detected wireless networks, highlight
the Add New Network option and press OK. Enter the
name of the network and select the security type using
the related options to connect.
Note: If the modem supports N mode, you should set
N mode settings.
If the selected network is password-protected, enter the
correct key by using the virtual keyboard. You can use this
keyboard via the directional buttons and the OK button
on the remote control.
Wait until the IP address is shown on the screen. This
means that the connection is now established.
Disconnect
If you have connected to a wireless network Disconnect
option will appear in the Network menu and your wireless
network profile will also be saved, thus your TV will
connect to the same network automatically whenever
you switch to wireless connection. To disconnect from
a wireless network and delete the saved wireless network
profile, highlight Disconnect and press OK.
Press WPS on your wifi router
If your router has WPS, you can directly connect to the
modem/router without entering a password or adding the
network first. Highlight Press WPS on your wifi router
option and press OK. Go to your modem/router device
and press the WPS button on it to make the connection.
You will see a connection confirmation on your TV once
If you require any technical guidance or find that your TV is not operating as intended, a simple solution can often be found in the Troubleshooting section of these instructions,
or online at www.bush-support.co.uk If you still require further assistance, call one of our experts on 0345 604 0105, a Bush enquiry line.
40 Advanced features
the devices have paired. Select OK to proceed. No further
configuration is required.
Internet Speed Test
Highlight Internet Speed Test and press the OK button
to check your internet connection speed.
Advanced Settings
Highlight Advanced Settings and press the OK button
to open the advanced setting menu. Use directional and
numeric buttons to set. The procedure is the same as
explained for wired connectivity. Highlight Save and press
the OK button to save settings when complete.
Networked Standby Mode
You can enable or disable the Networked Standby
Mode feature by setting this option accordingly. Refer
to Networked Standby Mode section for further
information.
Other Information
The status of the connection will be displayed as
Connected or Not Connected and the current IP address,
if a connection is established. The MAC address of your
TV will also be displayed on the screen.
Connecting to your mobile device via WLAN
• If your mobile device has WLAN feature, you can
connect it to your TV via a router, in order to access
the content in your device. For this, your mobile device
must have an appropriate sharing software.
Connect your TV to your router following the steps
mentioned in the sections above.
Afterwards, connect your mobile device to the router and
then activate the sharing software on your mobile device.
Then, select files that you want to share with your TV.
If the connection is established correctly, you will be able to
access the shared files installed on your mobile device via the
Audio Video Sharing feature of your TV.
Highlight the Audio Video Sharing option in the Sources
menu and press OK, available media server devices in the
network will be displayed. Select your mobile device and
press the OK button to continue.
• If available, you can download a virtual remote control
application from the server of your mobile device application
provider.
Note: This feature may not be supported on all mobile
devices.