Related Manuals for Mac Medical S0202-EST-KT
Summary of Contents for Mac Medical S0202-EST-KT
- Page 1 INSTRUCTION MANUAL Add-on Scrub Sink Timer Kit for Installation on Economy Processing Sinks Read and understand all of the instructions and safety information in this manual before operating this product. MAN-028 Rev B © 2021 MAC Medical, Inc. 08/2021...
- Page 2 Instruction Manual Table of Contents Parts List for S0202-EST-KT Plumbing Installation Timer (S0050) - Specifications and Terminal Connections Terminal Wiring Connections and Battery Replacement Timer Operation Display and Programming InLine Flow Switch Timer Controller (S0130-01) Specifications, Switch Rating and Wiring Diagram...
- Page 3 Instruction Manual Parts List for S0202-EST-KT Item # Part # Description S0050 Timer, Eagle S0130-01 Inline Flow Switch Timer Control - Brass S0090-01 Timer Housing Weldment S0019 Union 1/2” Copper S0049 Elbow, 1/2” Copper 90 S0165 Pipe Fitting Reducer, 1/2’ Sweat X 1/4” Npt Male S0069 1/2 Copper Hard Type L Cierro Brand 10’...
- Page 4 Instruction Manual Plumbing Installation The plumbing configuration on the sink before adding on the timer looks like the illustration below. bend line Cut pipe 2 inches below elbow (see red cut line). Cut the long, L-shaped pipe at the bend location on the back side (see red cut line).
- Page 5 Instruction Manual Note: S0069 pipe lengths shown are approximate and may vary according to original plumbing straightness. S0019 Unions S0049 Elbow S0019 Union See Detail inset below, left S0130-01 Timer S0165 Reducers (top and side) S0049 Elbows The cut original pipe is now located to the left from its previous position.
- Page 6 Instruction Manual Flow-switch Timer wiring runs up the interior side of the sink for connection to the read-out on the top of the sink (see red circled area). To mount the timer housing on the sink top, drill three holes using the hole dimension sizes and locations as shown in the illustration (below).
- Page 7 Instruction Manual Timer (S0050)- Specifications and Terminal Connections The timer is an Elapsed Time Indicator that is powered by an internal 3 volt lithium battery. It comes pre-assembled in its housing and ready for mounting to the sink. Specification Description Start/Stop Input NPN, Contact Closure;...
- Page 8 Instruction Manual Terminal Wiring Connections and Battery Replacement After threading the three flow-switch timer wires through the drilled hole on top of the sink, connect them to the timer read-out terminal connections as shown in the illustration below: Red Wire Orange Wire Black Wire Battery Replacement -...
- Page 9 Instruction Manual Timer Operation Display and Programming EAGLE SIGNAL VEEDER-ROOT 345678 1. Time Display 3. Next/Reset Key 2. Down Key Time Display: Accumulates time when the timing start input is active. Timing will not take place when the external or front panel reset is active. The leftmost digit is the time value legend.
- Page 10 Instruction Manual InLine Flow Switch Timer Controller (S0130-01) Specifications, Switch Rating and Wiring Diagram This is an explosion-proof brass flow switch, actuation set point 0.50 GPM (1.89 LPM), and calibrated for water at standard conditions. It is used for accurate detection of excessive or insufficient flow rates.
- Page 11 Instruction Manual Switch Timer Controller Maintenance Accumulation of foreign debris should periodically be removed from these switches. Occasional “wipe-down” cleaning when excessive contamination is present is all that is normally required. To Clean: Remove unit from system and disassemble as shown below. Clean all parts, reassemble and reinstall unit.
- Page 12 To place an order, contact our customer service department at 618-476-3550 or 877-828-9975 or by email at sales@macmedical.com Customer needs are our first priority. MAC Medical, Inc. Printed in USA Corporate Office Manufacturing Plant Publication No. MAN-028 Rev B 200 Admiral Weinel Blvd.