Subscribe to Our Youtube Channel
Related Manuals for MuxLab 100508
Summary of Contents for MuxLab 100508
- Page 1 HDMI 4x4 Matrix Switch 4K/60 Operation Manual 100508 © Muxlab Inc. 2020 94-000934-A / SE-000934-A...
- Page 2 ⚫ Unplug the power when left unused for a long period of time. ⚫ Information on disposal of devices: do not burn or mix with general household waste, please treat them as normal electrical waste. NOTICE: Please read this manual carefully before using this product. © Muxlab Inc. 2020...
-
Page 3: Table Of Contents
HDMI display. Any source is accessible at all times to any display, and may be selected via various control methods, including IR Remote Control, RS-232, TCP/IP or by using the selection buttons on the front panel. © Muxlab Inc. 2020... -
Page 4: Features
⚫ One (1) Quick Reference Sheet ⚫ One (1) HDMI Matrix IR Remote ⚫ One (1) RS232 Terminal Block Notes：Confirm that the product and accessories are all included. If not, please contact the supplier from which you purchased the unit. © Muxlab Inc. 2020... -
Page 5: Specifications
Storage Temperature −20 ºC to 60 ºC / −4 ºF to 140 ºF Relative Humidity 20 to 90 % RH (non-condensing) Compliance Regulatory: FCC, CE, RoHS Warranty 1 Year Ordering Information 100508 4X4 HDMI Matrix Switch, 4K/60 © Muxlab Inc. 2020... -
Page 6: Panels Description
Connect to a PC or Laptop via RS232 terminal to D-Sub 9-pin cable, for the transmission of RS-232 control commands. Ethernet Connect to your Ethernet network. May be managed via the device’s web interface, by a PC on the same network. © Muxlab Inc. 2020... -
Page 7: Remote Control
If a display is having difficulty receiving the HDMI signal, access the display’s menu and adjust the resolution (lowest to highest until signal is displayed). Please note that a 24 Hz vertical refresh rate may work better than 60 Hz or higher. © Muxlab Inc. 2020... -
Page 8: Web Gui Interface
2. Get the IP Address by CMD.exe. Enter “ping matrix” into CMD windows as follows. 3. Enter the IP Address into any web browser as follows. 4. Enter Username and Password to login the Web GUI Default Username is: admin Default Password is: admin © Muxlab Inc. 2020... - Page 9 In the EDID Management interface, the User can load a Default EDID to any input port, and you can also learn the EDID from any output port to any input port. © Muxlab Inc. 2020...
- Page 10 Installation Guide In the IP Settings tab, you can set the IP Settings such as: · Enable or disable DHCP · Host IP · Net Mask · Gateway NOTE: Default IP setting is with “DHCP” enabled. © Muxlab Inc. 2020...
-
Page 11: Control Protocol
All the commands start with 0xCC 0xDD. 2.1.2 Command type Command type code EDID Manage 0x01 Matrix port map manage 0x02 Network configuration 0x05 2.1.3 Checksum Checksum equal to 0xCC^0xDD^CommandType^length[0]^length[1]^Parameter[0]…^parameter[i] Example: 0Xcc 0Xdd 0x01 0x00 0x03 0x05 0x03 0x01 0x14 © Muxlab Inc. 2020... -
Page 12: Command Detail
4KX2KP60_2Ch PCM Audio 4KX2KP30_HD Audio_HDR 4KX2KP30_HD Audio 4KX2KP30_dolby_DTS5.1_HDR 4KX2KP30_dolby_DTS5.1 4KX2KP30_2CH AUDIO_HDR 4KX2KP30_2CH AUDIO 1080P60 HD PCM_HDR 1080P60 HD PCM 1080P60 Dolby_DTS5.1_HDR 1080P60 Dolby_DTS5.1 1080P60 2Ch audio_HDR 1080P60 2Ch audio 1080i60 HD AUDIO 1080i60 Dolby DTS 5.1 © Muxlab Inc. 2020... -
Page 13: Learn Edid From Sink
Example: Learning EDID from HDMI input 1 port to HDMI output 3 port. Command is: 0xCC 0xDD 0x01 0x00 0x03 0x04 0x02 0x00 0x15 Matrix port map manage（0x02） The matrix port map manage has four sub-commands (the first data of parameters is used for sub-command), sub-commands are © Muxlab Inc. 2020... -
Page 14: Map The Selected Output Port To The Specify Input Port
Data[1]: Connecting an HDMI input port to all the HDMI output ports 0→Input 1 1→Input 2 2→Input 3 3→Input 4 Example: Connect all the HDMI output ports to HDMI input 3 Command is: 0xCC 0xDD 0x02 0x00 0x02 0x02 0x02 0x11 © Muxlab Inc. 2020... -
Page 15: Read All The Output Mapping Information
Command type Length (2byte) parameters Checksum （1byte） (1byte) 0xCC 0xDD 0x05 0x00 0x0D 0x01 Data[1]~Data[12] 0xXX Parameter area description: 0x01: sub-command, set static IP address Data[1]~Data[4]: these four bytes indicates the setting IP address, example 192.168.31.113 © Muxlab Inc. 2020... -
Page 16: Read Matrix Switch Current Ip Information
Data[8]—0x00 (0) Data[9]~Data[12]: these four bytes indicates the gateway, example:192.168.31.1 Data[9]---0xC0 (192) Data[10]—0xA8 (168) Data[11]—0x1F (31) Data[12]—0x01 (1) Data[13]:This byte indicates the DHCP/static IP mode the matrix switch is set to, 1—DHCP mode, 0—static IP mode © Muxlab Inc. 2020... -
Page 17: Configure Dhcp/Static Ip Mode
Parameter Area description: 0x04: sub-comand, setting DHCP/static IP mode Data[1]: indicates DHCP mode/static IP mode， 1—DHCP mode, 0—static IP mode Example: setting matrix switch to static IP mode Command is: 0xCC 0xDD 0x05 0x00 0x02 0x04 0x00 0x12 © Muxlab Inc. 2020... - Page 18 All brand names and product names used in this document are trademarks, or registered trademarks of their respective holders. 2321 Cohen Road, Saint-Laurent, Quebec, Canada. H4R 2N7 Tel: (514) 905-0588 Fax: (514) 905-0589 Toll Free (North America): (877) 689-5228 E-mail: videoease@muxlab.com URL: © Muxlab Inc. 2020 www.muxlab.com...
Need help?
Do you have a question about the 100508 and is the answer not in the manual?
Questions and answers