EDIFIER X3s - TWS Earbuds Manual

Product description and accessories

Earbuds

Charging case

Type-C charging cable

Ear tips

Note:

• There are 4 sizes of ear tips included in the pack. Please select the suitable one to use.
• Images are for illustrative purposes only and may differ from the actual product.

Operating instructions

Charge

Earbuds

• Red LED blinks with prompt tone "low battery level, please charge.". Please place the earbuds in the case for charging.
• Red LED ON = Charging
• Red LED OFF = Fully charged

Charging Case

• Please connect the case to power source with the included Type-C charging cable for charging.
• Red LED ON = Charging
• Red LED OFF = Fully charged

Input:

• 5V 200mA (earbuds)
• 5V 1A (charging case)

• The rechargeable batteries that provide power for this product must be disposed properly for recycling. Do not dispose of batteries in fire to prevent an explosion.
• The power source used must be approved by relative departments and in accordance with electronic specifications of devices as well as local regulatory requirements (e.g. UL, CSA, VDE, CCC), otherwise there may be dangers of fire, explosion, etc.

Power on/off

1. Power ON when taken out of the case.
2. Power OFF when placed in the case.

Pairing

1. Taken out of the case.
2. Press and hold the touch panel on either earbud for 2-3s. Red and Blue LED will blink rapidly.
3. Select "EDIFIER X3s" in your device setting to connect.

Note for Pairing (1st)

1. Taken out of the case. Red and Blue LED will blink rapidly.
2. Select "EDIFIER X3s" in your device setting to connect.

Reset

1. Taken out of the case.
2. The earbuds have been interconnected, and not connected with any Bluetooth devices.
3. Quickly tap the touch panel on either earbud 3 times and hold to wait until the blue LED blinks rapidly, then the pairing record will be cleared.
4. Select "EDIFIER X3s" in your device setting to connect.

Left & Right connection

1. Placed in the case.
2. Quickly tap the touch panel on both earbuds 3 times and hold to wait until the blue LEDs blink rapidly, then left & right will start connecting.
3. Red LED will be steady lit after connected.

Controls

Play/pause: x1	Play/pause: x1
Previous track: x2	Next track: x2
Volume down:	Volume up:
Game mode switch: x3	Voice assistant: x3
Accept a call: x1	Accept a call: x1
End/reject a call: 2-3s	End/reject a call: 2-3s

Note:

1. : Press and hold.
2. Images are for illustrative purposes only and may differ from the actual product.

FAQs

When charging the charging case, the indicator is off.

• Please ensure the case is correctly connected with power source.

No sound

• Check if the earbuds are operating.
• Check if the earbuds volume is at an appropriate level.
• Check if the earbuds are correctly connected with mobile phone.
• Check if the earbuds are operating within a normal working range.

The call quality of the earbuds is bad.

• Check if mobile phone is in an area with strong signal.
• Please ensure the earbuds are within effective distance (10m) and no obstacle between the earbuds and mobile phone.

When playing music, cannot control pause/play/previous track/next track via the earbuds.

• Please ensure the paired device support AVRCP (Audio/Video Remote Control Profile) profile.

Model: EDF200060

Edifier International Limited
P.O. Box 6264
General Post Office
Hong Kong

www.edifier.com
© 2021 Edifier International Limited. All rights reserved.
Printed in China

NOTICE:

For the need of technical improvement and system upgrade, information contained herein may be subject to change from time to time without prior notice.

Products of EDIFIER will be customized for different applications. Pictures and illustrations shown on this manual may be slightly different from actual product. If any difference is found, the actual product prevails.