Table of Contents
Advertisement
WARNING:
• Operation of this product in a residential environment could cause radio interference.
Caution:
• The DC/AC power supply connected to the camera
must be in the same building.
• The network camera is only intended for a connection
to an ethernet or PoE network without routing to the
outside plant.
• This product has no power switch. Be sure to install
disconnect devices such as a circuit breaker to shut
down the main power of power supplying equipment
to this product.
• Only connect 24 V AC Class 2 power supply (UL
1310/CSA 223), limited power source (IEC/EN/UL/
CSA 60950-1, IEC/EN/UL/CSA 62368-1 Annex Q) or
IEC/EN/UL/CSA 62368-1 PS2.
• Before attempting to connect or operate this product,
please read these instructions carefully.
Precautions
■ Do not insert any foreign objects.
Fire or electrical shock may be caused if water or any foreign objects, such as metal objects, enter inside the unit.
Turn the power off immediately and contact qualified service personnel for service.
■ Do not use this product in an inflammable atmosphere.
Failure to observe this may cause an explosion resulting in injury.
■ Avoid installing this product in the locations where salt damage occurs or corrosive gas
is produced.
Otherwise, the mounting portions will deteriorate and injury or accidents due to a fall of the product may occur.
■ Do not strike or give a strong shock to this product.
Failure to observe this may cause injury or fire.
■ Keep microSD memory cards away from infants and children.
Otherwise, they may swallow the cards by mistake.
In this case, consult a doctor immediately.
■ Do not hang down from this product or use this product as a pedestal.
Failure to observe this may cause injury or accidents.
■ Do not damage the power cable.
Do not damage, fabricate, twist, stretch, bundle, or forcibly bend the power cable. Do
not place heavy objects on it, and keep it away from heat sources.
Use of a damaged power cable may cause electric shock, short circuit, or fire.
Consult the dealer for repair.
■ Do not install this product on a place that is greatly influenced by wind.
Installation on a place where the wind speed is 60 m/s {approx. 134 mph} or more may cause a fall of the prod-
uct resulting in injury or accidents.
■ Do not sprinkle more water, exceeding the performance limit of waterproof with a high
pressure cleaning machine, etc.
Fire or electrical shock may be caused by immersion.
Notice:
• This product is not suitable for use in locations
where children are likely to be present.
• Do not install this product in locations where
ordinary persons can easily reach.
• This product is a professional equipment.
• For information about screws and other parts
required for installation, refer to the correspond-
ing section of this document.
: Direct current symbol
: Alternating current symbol
■ Do not attempt to disassemble or modify this product.
Doing so can cause fire, electric shock, etc.
Ask your dealer for repair and inspection.
■ Do not install or clean the camera, or touch this product, the power cable or the
connected cables during thunder storms.
Failure to observe this may cause electric shock.
■ Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric shock, injury,
or damage to the product.
Be sure to consult the dealer.
■ Stop the operation immediately when something is wrong with this product.
When smoke goes up from the product, the smell of smoke comes from the product, or the exterior of the product
has deteriorated, continued use will cause a fire or fall of the product resulting in injury, or damage to the property.
In this case, turn the power off immediately and contact qualified service personnel for service.
■ Select an installation area that can support the total weight.
Selecting an inappropriate installation surface may cause the product to fall down or topple over, resulting in
injury or accident.
Installation work shall be started after sufficient reinforcement.
■ Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a fall of the product resulting in injury or accidents.
Consult the dealer for the inspections.
■ The exclusively designed mount bracket shall be used.
Failure to observe this may cause a drop resulting in injury or accidents.
Use the exclusively designed mount bracket for installation.
■ The screws and bolts must be tightened to the specified torque.
Failure to observe this may cause a drop resulting in injury or accidents.
■ Turn the power off when do wiring of this product.
Failure to observe this may cause electric shock. In addition, short circuit or wrong wiring may cause fire.
■ Install this product in a location high enough to avoid people and objects from bumping
the product.
Failure to observe this may cause injury.
■ The measures of protection against a fall of this product shall be taken.
Failure to observe this may cause a drop resulting in injury.
Be sure to install the safety wire.
■ The measures of protection against snowfall shall be taken.
Weight of snow may cause a fall of the product resulting in injury or accidents.
Protect the product against snowfall by installing it under eaves.
■ Do not install this product in locations subject to vibration.
Loosening of mounting screws or bolts may cause a fall of the product resulting in injury or accidents.
■ Correctly perform all wiring.
Short circuits in the wiring or incorrect wiring may cause fire or electrical shock.
■ Install the product securely on an installation surface in accordance with the installation
instructions.
Failure to observe this may cause injury or accidents.
■ Turn the power off when cleaning this product.
Failure to observe this may cause electric shock.
■ Do not rub the edges of metal parts with your hand.
Failure to observe this may cause injury.
2
Advertisement
Table of Contents
