Kurzweil K2500 Reference Manual page 47

PAGE 2
LoopLength On or Off
Fdbk Image -100 to 100%
Tap1 Delay 0 to 32 bts
Tap1 Shapr 0.10 to 6.00 x
Tap1 Level 0 to 100%
Tap1 Bal -100 to 100%
PAGE 3
Tap3 Delay 0 to 32 bts
Tap3 Shapr 0.10 to 6.00 x
Tap3 Pitch C-1 to C8
Tap3 PtAmt 0 to 100%
Tap3 Level 0 to 100%
Tap3 Bal -100 to 100%
PAGE 4
Tap5 Delay 0 to 32 bts
Tap5 Shapr 0.10 to 6.00 x
Tap5 Pitch C-1 to C8
Tap5 PtAmt 0 to 100%
Tap5 Level 0 to 100%
Tap5 Bal -100 to 100%
Wet/Dry
Out Gain
Fdbk Level
HF Damping
LF Damping
Tempo
Diff Dly
Diff Amt
LoopLength
Tap2 Delay
Tap2 Shapr
Tap2 Pitch
Tap2 PtAmt
Tap2 Level
Tap2 Bal
Tap4 Delay
Tap4 Shapr
Tap4 Pitch
Tap4 PtAmt
Tap4 Level
Tap4 Bal
Tap6 Delay
Tap6 Shapr
Tap6 Pitch
Tap6 PtAmt
Tap6 Level
Tap6 Bal
The relative amount of input signal and effected signal that is to appear in the Þnal effect
output mix. When set to 0%, the output is taken only from the input (dry). When set to
100%, the output is all wet. Negative values polarity-invert the wet signal.
The overall gain or amplitude at the output of the effect.
The amount that the feedback tap is fed to the input of the delay.
The amount of high-frequency content of the signal to the input of the delay. This control
determines the cutoff frequency of the one-pole (-6dB/octave) lowpass Þlters.
The amount of low-frequency content of the signal to the input of the delay. This control
determines the cutoff frequency of the one-pole (-6dB/octave) hipass Þlters.
Basis for the rates of the delay times, as referenced to a musical tempo in BPM (beats per
minute). When this parameter is set to ÒSystemÓ, the tempo is locked to the internal
sequencer tempo or to incoming MIDI clocks. When it is set to ÒSystemÓ, sources (FUNs,
LFOs, ASRs etc.) will have no effect on the Tempo parameter.
The length that the diffuser smears the signal sent to the input of the delay.
The intensity that the diffuser smears the signal sent to the input of the delay. Negative
values decorrelate the stereo signal.
The delay length of the feedback tap in 24ths of a beat. The length of a delay in seconds
can be calculated as T = (beats/tempo) * 60.
FXAlg #135: Spectral 4-Tap ¥ FXAlg #136: Spectral 6-Tap
0 to 32 bts
0.10 to 6.00 x
C-1 to C8
0 to 100%
0 to 100%
-100 to 100%
0 to 32 bts
0.10 to 6.00 x
C-1 to C8
0 to 100%
0 to 100%
-100 to 100%
0 to 32 bts
0.10 to 6.00 x
C-1 to C8
0 to 100%
0 to 100%
-100 to 100%
Algorithm Reference-47