Table of Contents
Advertisement
Wireless Blu-ray Disc Player
Power
Problem
Solution
No power
Make sure that the power cord is plugged into a power
outlet and that the outlet is supplying power.
The player switches to
After a period of inactivity, your player switches to
standby mode
standby mode automatically. This is a power saving
feature.
If your player switches to standby mode unexpectedly, a
safety device may have been activated. Press
STANDBY/ON on the front of your player.
Operation
Problem
Solution
Remote control does not work
• Make sure that you are pointing the remote
• Make sure that there are no obstructions
• Make sure that there is no colored glass
• Make sure that the remote control sensor is
• Replace the batteries.
Some or all functions do not
• Some functions are not allowed by the disc, for
work
• Condensation may have formed inside your
• Reset your player. For instructions, see
Playback fails to start or starts
• Make sure that the disc is inserted face up in
then stops even when
(play/pause) is pressed
• Make sure that the disc is not dirty. For
• The disc may be blank or incompatible with
Start up is slow and audio and
• If power has been interrupted or the power
video output takes a long time
• If your player is connected to the TV with an
When reading a disc, the disc
• Make sure that the disc is not dirty. For
tray opens
• The disc may be incompatible with your
• Reset your player. For instructions, see
Audio or video pause during
• Make sure that the disc is not dirty. For
playback
• Reset your player. For instructions, see
The player is on and the logo
• Make sure that the disc is not dirty. For
and menu appear, but there is
no image from the disc
• Reset your player. For instructions, see
control at the remote control sensor on the
front of your player.
between the remote control and the remote
control sensor on the front of your player.
between the remote control and the remote
control sensor on the front of your player.
Colored glass, such as the glass door of an
entertainment center, can interfere with
signal reception.
not exposed to direct sunlight or bright light.
These can interfere with signal reception.
example, fast-forwarding through the
warning information at the beginning of the
disc.
player. Turn off your player and wait one to
two hours for the condensation to evaporate.
"Resetting your player" on page 22.
the disc tray.
instructions, see "Cleaning discs" on page 22.
your player. Try another disc.
cord has just been connected, startup is slow.
This is not a defect.
HDMI cable, startup is slow. This is not a
defect.
instructions, see "Cleaning discs" on page 22.
player. Try another disc.
"Resetting your player" on page 22.
instructions, see "Cleaning discs" on page 22.
"Resetting your player" on page 22.
instructions on cleaning a disc, see "Cleaning
discs" on page 22.
"Resetting your player" on page 22.
www.insigniaproducts.com
Problem
Solution
The player freezes when
• Reset your player. For instructions, see
reading a disc
• If your player freezes again, the disc may
• Make sure the firmware is up to date. See
TV screen and video
Problem
Solution
Video does not appear on the
TV screen or the picture is
distorted
Video is not output in high
definition
The 4:3 aspect ratio picture
expands left and right or the
picture size is incorrect
There is no apparent change in
the picture quality when the
picture settings are changed in
the Setup menu
When playing a BD-Live disc,
the screen is black
HDMI connections
Problem
Solution
The 4:3 aspect ratio picture
• Change TV Aspect on your player to 16:9.
expands left and right or the
picture size is incorrect
"Resetting your player" on page 22. When you
see "loading" on the screen, press
(open/close) to open the disc tray and remove
the disc. Clean the disc. (For instructions, see
"Cleaning discs" on page 22), then try the disc
again.
contain some content that is not compatible
with your player. Do no try playing the disc
with your player.
"Upgrading your player's firmware" on
page 21.
• Make sure that the TV is connected to the
correct jacks on the back of your player.
• Make sure that the TV is set to the correct
video input source.
• The TV may be in screen saver mode. Check
the documentation that came with the TV for
instructions about "waking" your TV.
• Reset your player. For instructions, see
"Resetting your player" on page 22.
• High definition video cannot be output
through the VIDEO jack. You must connect
the TV to your player using the COMPONENT
jacks or HDMI jack.
• Make sure that the correct HDMI or
component video resolution has been
selected in the Setup menu. See "Selecting
the video output resolution" on page 13.
• Depending on the Blu-ray Disc, output from
the COMPONENT VIDEO jacks may be
restricted to 480p.
• Use the TV to change the aspect ratio. See the
documentation that came with the TV.
• When using a component video cable, set TV
Aspect on your player to 4:3 Pan & Scan.
See "Selecting the TV aspect ratio" on
page 13.
• Depending on the video type, changes may
not be apparent.
• Erase BD Storage. See "Erasing BD-Live
storage" on page 19.
• Make sure that your Internet connection is
working.
• Make sure that the Internet cable is
connected securely and correctly to your
player and the Internet jack. Some discs
require an Internet connection to play.
See "Selecting the TV aspect ratio" on
page 13.
23
Advertisement
Table of Contents
