Advertisement
To reset the moonroof control unit, do this:
1. Turn the ignition switch to LOCK (0).
2. Press and hold the tilt switch, and turn the ignition
switch to ON (II).
3. Release the tilt switch, and turn the ignition switch
to LOCK (0).
4. Repeat steps 2 and 3 four times.
5. Press and hold the moonroof open switch for
3 seconds after the moonroof is fully opened.
6. Press and hold the moonroof close switch for
3 seconds after the moonroof is fully closed (tilted).
7. Confirm that the moonroof control unit is reset by
using the moonroof AUTO OPEN and AUTO
CLOSE functions.
For more information, refer to the Body Electrical
section of the 2008 MDX Service Manual.
NOTE: The moonroof auto-reverse feature does not
require initialization, and disconnecting the battery
does not require initialization of the AUTO function.
The moonroof can also be opened with the remote
transmitter.
Check/Refresh the XM Satellite Radio Dealer
Demo Service
The XM Satellite Radio comes from the factory
activated with the dealer demo service. Once you
install the No. 4 fuse, the XM radio will receive the full
range of available XM channels. Make sure this service
is activated by checking if the radio is getting channels
000, 001, 007, 009, 047, 122, 174, and 247. If it is not,
do a rapid refresh on the iN (Interactive Network).
Without the dealer demo service activated, the XM
radio only displays channels 000, 001, 174, and 247.
To check if the dealer demo service is activated, do
this:
1. Turn the ignition switch to ON (II). Turn on the
radio, and enter the audio unit anti-theft code. Then
press the XM button.
2. Make sure the radio is in CHANNEL MODE, not
CATEGORY MODE. Press and hold the DISP-
MODE button for 6 seconds (models without
navigation), or touch the MODE icon (models with
navigation) to switch between modes.
3. Tune to channel 001 (the XM preview channel) to
make sure you are receiving the XM signal. If you
do not get a clear signal, park the vehicle outside
where there is a clear view of the southern sky.
07-044
4. Turn the TUNE knob on the audio unit display.
• If you can tune to channels 000, 001, 007, 009,
047, 122, 174, and 247, the dealer demo service
is activated. Tune to channel 001 and leave the
radio turned on for 7 minutes to refresh the
dealer demo service. No further action is needed.
• If you can only tune to channels 000, 001, 174,
and 247, the dealer demo service is not yet
activated, and an activation refresh needs to be
done. Go to step 5.
5. Turn the TUNE knob to 000, then write down the
8-digit XM radio ID number you see in the audio
unit display. You need this number, your dealer
number, and the VIN to do an activation refresh of
the dealer demo service. Then go to step 6.
NOTE:
• If you cannot tune to channel 000, you are in
CATEGORY MODE. See step 2 to switch from
CATEGORY MODE to CHANNEL MODE.
• The ID number does not include the letters I, O,
S, or F.
6. Go to an iN workstation.
NOTE: If you do not have access to iN, call XM
Satellite Radio at (800) 852-9696, and follow the
instructions of the automated menu. When the
agent answers, ask for a rapid dealer activation
refresh, then go to step 9.
7. From the iN main menu, click on SERVICE, click on
Service Bay, and then click on XM Radio. This
brings up the DEALER ACTIVATION REFRESH
screen.
NOTE: If you cannot bring up this display, call the
iN Support Center at (800) 245-4343.
8. Enter the 8-digit XM Satellite Radio ID number you
wrote down in step 5. Then click on Submit. You
will see the ACTIVATION REFRESH screen once
the ID number is recognized.
NOTE: If you entered the ID number incorrectly, or
it was not recognized, you will see an error display.
If this happens, follow the instructions on the
display.
9. Turn the TUNE knob to 001 to make sure you are
receiving the XM signal. If you do not get a clear
signal, park the vehicle outside where there is a
clear view of the southern sky, then go to step 10.
10. Leave the radio on for at least 10 minutes, then go
to step 11.
5 of 7
Advertisement
