Page 1
ASSEMBLY, MAINTENANCE, & USER MANUAL MODEL # SFTH400-A WARNING Read all precautions and instructions in DL/CR 2032 button cell this manual before using this equipment. battery required (not included) Skywalker Holdings LLC Save this manual for future reference. P.O. Box 574, Brigham City, UT 84302...
TABLE OF CONTENTS Part List.....................................3 Part Identification.................................4-6 Exploded Drawing................................7 Assembly....................................8-14 Sensor Instruction................................15 Warning & Maintenance...............................16 Limited Warranty................................17-18 STOP EVERYTHING YOU'RE DOING AND REGISTER YOUR PRODUCT Find our warranty registration online by typing in: www.skywalkertrampolines.com/registration/ You'll need to have the following information handy: •...
PART IDENTIFICATION Before you begin, take a look at the drawings below to make sure you have all the parts. The numbers in the squares to the left (key numbers) will help you identify the parts during assembly. Horizontal Handle Frame Assembly (x1) Upper Handle (x1) (x1)
Page 5
Adjustable Foot (x1) End Cap 1 (x5) End Cap 2 (x1) Pre-installed Pre-installed Pre-installed M6x65 Bolt (x5) Frame (x1) Leg (x5) Pre-installed Pre-installed Pre-installed M6 Nut (x5) Elastic with Ball (x25) Sensor (x1) Pre-installed Pre-installed S5 Wrench (x1) Wrench (x1) Mobile Device Stand (x1) (assembly needed)
Page 6
PART IDENTIFICATION Before you begin, take a look at the drawings below to make sure you have all the parts. The numbers in the squares to the left (key numbers) will help you identify the parts during assembly. M12 Washer (x3)
ASSEMBLY READ THIS BEFORE YOU BEGIN • You’ll probably need 1 adult and 20 minutes to assemble your trampoline (of course, that depends on what model you have, and whether or not you’re secretly a superhero). • We’ve provided a wrench to help with assembly, but you’re more than welcome to use your own tools. •...
Page 9
STEP 3 Insert the upper handle (3) into the lower handle (4) and tighten with the curl knob (6) as shown. Note: The height of the handle can be adjusted with the three holes on the upper handle. Lower Handle Curl Knob (x1) (x1) STEP 4...
Page 10
ASSEMBLY STEP 5 Insert a knob (6) into the hole on the top of each leg (17) and twist to tighten. Note: Make sure the knobs are tight before each use of the trampoline. Knob (x5) (17) STEP 6 Connect the lower handle (4) to the trampoline frame by sliding the open tube of the handle onto the tube on the underside of the frame (1) and placing...
Page 11
STEP 7 After the handle is installed, if its feet do not make contact with the ground, you can adjust the height using the spare M12 washers (25) on the end cap 2 (14) and adjustable foot by rotating the (15).
Page 12
ASSEMBLY STEP 9 Now to assemble the mobile device stand, attach the two upright pole A’s and one upright pole B together with two screw sleeves as shown. ( The screw sleeve may be pre-installed in the upright pole pieces.) Upright pole A Screw sleeve Upright pole A...
Page 13
ASSEMBLY STEP 11 Screw the adjusting pole into the upright pole B with screw sleeve as shown. Adjusting pole Upright pole B STEP 12 Slide the locking cap over the ball of the adjusting pole and temporarily rest it on the adjusting pole. Adjusting pole Locking cap Locking cap...
Page 14
ASSEMBLY STEP 13 Place the mobile bracket onto the ball of the adjusting pole. Now, bring down the locking cap you placed in previous step and twist it to tighten the mobile bracket on as shown. Note :The mobile bracket can be rotated to adjust the angle. Locking cap Adjusting pole mobile bracket...
SENSOR INSTRUCTION STEP 1 open Turn the sensor over and use a screwdriver to open the back cover. Place a DL/CR 2032 button cell battery (not included ) into the sensor making sure the positive side “+” is facing up. Then close replace the sensor cover.
WARNING & MAINTENANCE FCC WARNING This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordan- ce with the instructions, may cause harmful interference to radio communications.
LIMITED WARRANTY Skywalker Holdings, LLC warrants its products to be free from defects in material and workmanship under normal use and service conditions. This product is warranted for three (3) years after the date of purchase. Warranty coverage extends only to the original retail purchaser from the date of original purchase. This warranty is only valid concerning products used for residential use.
Page 18
NOTE: SKYWALKER HOLDINGS, LLC IS NOT RESPONSIBLE OR LIABLE FOR INDIRECT, SPECIAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE PRODUCT OR OTHER DAMAGES WITH RESPECT TO ANY ECONOMIC LOSS, LOSS OF PROPERTY, LOSS OF REVENUE OR PROFITS, LOSS OF ENJOYMENT OR USE, COST OF REMOVAL, INSTALLATION OR OTHER CONSEQUENTIAL DAMAGES.
Need help?
Do you have a question about the SFTH400-A and is the answer not in the manual?
Questions and answers