Agilent Technologies 6023A Operating Manual page 16

Agilent Technologies Model
DC Output: Voltage, current and power spans indicate range
over output may be varied using front panel controls.
Load Effect (Load Regulation) Voltage load effect is given for a load
current change equal to the current rating of the supply. Current load
effect is given for a load voltage change equal to the voltage rating of the
supply.
Source Effect (Line Regulation): Given for a change within the rated line
voltage for any output within the rated output voltage, current and
power of the supply
PARD (Ripple and Noise): Measured at any line voltage and under any
load condition within rating (rms 10 Hz to 10 Mhz/p-p 10 Hz to
20 MHz)
Load Effect Transient Recovery: Maximum time required for output
voltage to recover with the specified band around the nominal output
voltage following a 10% step change in output current while operating in
the constant voltage mode
Programming: (25 5 C) Given for control of the
output over the GP-IB or with front panel controls
Remote Voltmeter: (25 5 C) Refers to data read back to the controller
over the GP-IB
Remote Ammeter: (25 5 C) Refers to data read back to the controller
over the GP-IB.
Front Panel Voltmeter: (25 5 C)
Front Panel Ammeter: (25 5 C)
Agilent Technologies Model
Programming: (25 5 C) Given for control of the
output over the GP-IB or with front panel controls
Remote Voltmeter: (25 5 C) Refers to data read back to the controller
over the GP-IB
Remote Ammeter: (25 5 C) Refers to data read back to the controller
over the GP-IB.
Front Panel Voltmeter: (25 5 C)
Front Panel Ammeter: (25 5 C)
Maximum AC Input Current: +6% -13% (48-63) Hz
Temperature Coefficient: Output change per degree Celsius change
in ambient following 30 minute warm-up.
Drift (Stability): Change in output (dc to 20 Hz) over 8-hour internal
under constant line, load, and ambient following 30-minute warm-up
Programming Response Time: The maximum time required
to change from zero volts to full scale voltage or from full
scale voltage to 2 volts ( 5 volts for Agilent 6035A) and settle
within the specified band. Full load is defined as the
resistance equal to Vp1/Ip1. Light load is as specified
Overvoltage Protection: Trip voltage adjustable via front
panel control using the Display OVP function
Typical input power at rated output power: (see point P
General Information
16
Table 1-1. Performance Specifications
Table 1-2. Supplemental Characteristics
100 Vac (Opt.100)
120 Vac (Std.)
220 Vac (Opt.220)
240 Vac (Opt.240)
Up
Down
on Figure 1-1)
2
6033A
Volts 0-20 V
Amps 0-30 A
Maximum Power 200-240 W
Voltage 0.01% + 2 mV
Current 0.01% + 9 mA
Voltage 0.01% + 1 mV
Current 0.01% + 6 mA
Voltage 3 mV/30 mV
1
Current 30 mA/
Time 1 ms
Level 50 mV
Voltage Accuracy 0.035% + 9 mV
Current Accuracy 0.15% +20 mA
Accuracy 0.07% + 6 mV
Accuracy 0.3% + 25 mA
Range 2 V, 20 V, 200 V
Accuracy 0.07% +6 mV, 11
mV, 56 mV
Range 20 A, 200 A
Accuracy 0.3% + (20 mA, 65
mA)
6033A
Voltage Resolution 5 mV
Current Resolution 7.5 mA
Resolution 5 mV
Resolution 7.5 mA
Resolution 5 mV, 10 mV, 100
mV
Resolution 10 mA, 100 mA
6.0 A
6.5 A
3.8 A
3.6 A
Voltage 50 ppm + 0.6 mV
Current 100 ppm + 2 mA
Voltage 0.02 % + 1 mV
Current 0.03% + 10 mA
Settling Band 5 mV
Full Load 100 ms
No Load 100 ms
Full Load 200 ms
Light Load
500 ms (50 )
Range 0-23 V
Resolution 100 mV
Accuracy 0.3% + 200 mV
340 W
6038A
0-60 V
0-10 A
200-240 W
0.01% + 3 mV
0.01% + 5 mA
0.01% + 2 mV
0.01% + 2 mA
3 mV/30 mV
1
5 mA/
1 ms
75 mV
0.035% + 40 mV
0.085% + 10 mA
0.07% + 50 mV
0.2% + 11 mA
2 V, 20 V, 200 V
0.07% + 50 mV, 55
mV, 100 mV)
20 A
0.2% + 11 mA
6038A
15 mV
2.5 mA
15 mV
2.5 mA
15 mV, 15 mV, 100
mV
10 mA
6.0 A
6.5 A
3.8 A
3.6 A
50 ppm + 3 mV
90 ppm + 0.3 mA
0.02% + 2 mV
0.03% + 3 mA
15 mV
150 ms
120 ms
150 ms
750 ms (400 )
0-63 V
100 mV
0.25% + 300 mV
325 W