Related Manuals for Agilent Technologies 6010A
Summary of Contents for Agilent Technologies 6010A
- Page 1 DC AUTORANGING POWER SUPPLY Agilent Part Number 5964-8120 Microfiche Part No. 5964-8121 USER’S GUIDE AGILENT 6010A, 6011A, 6012B, 6015A, 6023A and 6028A Printed in Malaysia September, 2004...
- Page 2 90 days from date of delivery. During the warranty period Agilent Technologies will, at its option, either repair or replace products that prove to be defective. Agilent does not warrant that the operation for the software firmware, or hardware shall be uninterrupted or error free.
-
Page 3: Safety Summary
Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized modifications to the instrument. Return the instrument to an Agilent Technologies Sales and Service Office for service and repair to ensure that safety features are maintained. - Page 4 SAFETY SYMBOLS Direct current Alternating current Both direct and alternating current Three-phase alternating current Earth (ground) terminal Protective earth (ground) terminal Frame or chassis terminal Terminal is at earth potential. Used for measurement and control circuits designed to be operated with one terminal at earth potential.
-
Page 5: Declaration Of Conformity
This DoC applies to above-listed products placed on the EU market after January 1, 2004 Date For further information, p lease contact your local Agilent Technologies sales office, agent or distributor, or Agilent Technologies Deutschland GmbH, Herrenberger Stra e 130, D71034 Böblingen, Germany Revision: B.00.00... - Page 6 Acoustic Noise Statement Herstellerbescheinigung Diese Information steht im Zusammenhang mit den Anforderungen der Maschinenlärminformationsverordnung vom 18 Januar 1991. * Schalldruckpegel Lp < 70 dB(A) * Am Arbeitsplatz * Normaler Betrieb * Nach DIN 45635 T. 19 (Typprüfung) Manufacturer’s Declaration This statement is provided to comply with the requirements of the German Sound Emission Directive, from 18 January 1991.
-
Page 7: Table Of Contents
Rack Mounting... 18 Input Power Requirements ... 18 Power Connection ... 19 Agilent Models 6010A, 6011A, 6012B, and 6015A ... 19 Agilent Models 6023A, 6028A ... 19 Line Voltage Option Conversion... 20 Agilent Models 6010A, 6011A, 6012B, and 6015A ... 20 Agilent Models 6023A, 6028A ... - Page 8 Multiple-Supply Operation... 39 Auto-Parallel Operation ... 39 Series Operation ... 40 Monitor Signals... 41 100 VAC Input Power Option 100 General Information ... 43 Description ... 43 Scope of Appendix A ... 43 Using Appendix A... 43 Section 1 Manual Changes ..43 Section 2 Manual Changes ...
-
Page 9: General Information
550 Vdc on models 6010A and 6015A from chassis ground. The power supply is fan cooled and is packaged in an Agilent Technologies System II-compatible modular that provides easy access for servicing. A thermostat shuts down the supply if an over-temperature condition occurs and resets automatically. -
Page 10: Accessories
Option Description Input power: 100 Vac + 6%, -10%; 48-63 Hz single phase. Input power: 120 Vac +6%, -13%. 48-63 Hz single phase. Input Power: 220 Vac +6%, -13%; 48-63 Hz, single phase. Input power: 240 Vac +6%, -13%; 48-63 Hz, single phase. Rack mount kit for two units side by side (models 6023A and 6028A only) Rack mounting kit Flanges with Handles... -
Page 11: Instrument & Manual Identification
One User’s Guide is shipped with each power supply. Additional User’s Guides and Operating and Service manuals may be purchased directly from your local Agilent Technologies Sales office. Specify the model number, serial number prefix, and the manual part number provided on the title page. (When ordered at the same time as the power supply, additional manuals may be purchased by adding Option 910 to the order. - Page 12 Agilent Technologies Model DC Output: Voltage, current and power spans indicate range over which output may be varied using front panel controls. Load Effect (Load Regulation) Voltage load effect is given for a load current change equal to the current rating of the supply. Current load effect is given for a load voltage change equal to the voltage rating of the supply.
- Page 13 6012B 6015A 0-60 V 0-500 V 0-50 A 0-5 A 1000-1200 W 1000-1050 W 0.01% + 5 mV 0.01% + 40 mV 0.01% + 10 mA 0.03% + 34 mA 0.01% + 3 mV 0.01% + 13 mV 0.01% + 10 mA 0.03% + 17 mA 0.005% + 5 mV/40 mV 50 mV/160 mV...
- Page 14 DC Floating Voltage: Either output terminal may be floated up to the following voltage (including the output voltage) from earth ground: 240 Vdc on Models 6011A, 6012B, 6023A, and 6028A 550 Vdc on Models 6010A and 6015A Exceeding these voltages can result in damage to the equipment. Efficiency (typical): 80% on maximum output boundary Remote Sensing: The power supply maintains specifications at the load with up to 0.5 Volt per load lead with sense wire...
- Page 15 Model Agilent Agilent 6010A 6011A 200 V 20 V 50 A 120 V 14 V 10 A 76 A 60 V 17 A 120 A Figure 1-1. Output Characteristic Curve Agilent Agilent Agilent 6012B 6015A 6023A 60 V 500 V 20 V 17.5 A...
- Page 16 Figure 1-2. Output Impedance General Information...
-
Page 17: Installation
Save all packing materials until the inspection is completed. If damage is found, file a claim with the carrier immediately. The Agilent Technologies Sales and Support office should be notified as soon as possible. -
Page 18: Outline Diagram
Figure 2-1 illustrates the outline shape and dimensions of the cabinet. 6023A ONLY Bench Operation The supply cabinet has plastic feet, which are shaped to ensure self-aligning when stacked with other Agilent Technologies System II cabinets. Rack Mounting The supply can be mounted in a standard 19-inch rack enclosure. Rack mounting accessories for these units are listed in the ACCESSORIES paragraph in Section I. -
Page 19: Power Connection
The power supply is shipped from the factory with a power-cord plug appropriate for the user’s location. Figure 2-2 illustrates the standard configuration of power-cord plugs used by Agilent Technologies. With each drawing is the Agilent Part Number for a replacement power cord equipped with a plug of that configuration. If a different power cord is required, contact the nearest Agilent Technologies Sales and Service office. -
Page 20: Line Voltage Option Conversion
Failure to configure and calibrate the power supply properly may result in damage to the unit. Agilent Models 6010A, 6011A, 6012B and 6015A. Line voltage conversion is accomplished by adjusting three components: a two-section line select switch, and a line-voltage jumper. -
Page 21: Agilent Models 6023A, 6028A
Option 831, 8120-5573, 12 AWG unterminated Option 833, 8120-5568, 1.5 mm2 unterminated Option 834, 8120-5566, 10 AWG unterminated Option 845 Option 846 8120-5570 8120-5565 Agilent 6010A, 6011A, 6012B, Option 903 Option 902 8120-1348 8120-1689 standard HP 6023A, 6028A #8 Ring... - Page 22 Agilent 6010A, 6011A, 6012B, 6015A Agilent 6023A, 6028A Figure 2-3. Line Voltage Conversion Components 22 Installation...
-
Page 23: Ac Line Impedance Check
To insure safe shipment of the instrument, it is recommended that the package designed for the instrument be used. The original packaging material is reusable. If it is not available, contact your local Agilent Technologies Sales and Support office to obtain the materials. This office will also furnish the address of the nearest service office to which the instrument can be shipped. -
Page 24: Rear Panel Screw Sizes And Part Numbers
Rear Panel Screw Sizes and Part Numbers Refer to the following list if you need to replace any of the rear panel connection hardware: Agilent Models 6010A, 6011A, 6012B and 6015A Item ac input cover ac input cover screws ac input barrier block... -
Page 25: Operating Instructions
Operating Instructions Introduction This section describes the operating controls and indicators, turn-on checkout procedures, and operating procedures and considerations for the power supply. Front-panel operation and remote resistance/voltage programming is described in this section. The front-panel controls and indicators are shown in Figure 3-1 and described in Table 3-1. Table 3-1 also lists the pages, in which, use of the controls and indicators is described. -
Page 26: Turn-On Checkout Procedure
Number Controls/Indicators LINE Switch VOLTAGE CONTROL CURRENT CONTROL OVP ADJUST Voltage Display Current Display DISPLAYS SETTINGS Pushbutton Switch DISPLAY OVP Pushbutton Switch CV Status Indicator CC Status Indicator UNREGULATED Status Indicator OVERVOLTAGE Status Indicator OVERTEMPERATURE Status Indicator Turn-On Checkout Procedure WARNING: Before the instrument is turned on, all protective earth terminals, extension cords, and devices connected to the power supply should be connected to a protective earth ground. - Page 27 Check that the rear-panel mode switches are set as shown in Figure 3-3. Check that + lead is connected to +S and the – lead is connected to –S and tightened securely. The + Sense lead is connected to + Output and the Check that the rear panel label indicates that the unit is set for the mains input voltage to be used.
-
Page 28: Initial Setup & Interconnections
Initial Setup and Interconnections WARNING: Turn off input ac power before changing any rear-panel connection and make certain all wires and straps are properly connected and terminal block screws are securely tightened before reapplying power. Be certain to replace both terminal block covers before reapplying power to avoid exposing the operator to hazardous voltages. - Page 29 Table 3-2. Maximum Wire Lengths To Limit Voltage Drops Wire Size Cross-section (mm 0,75 * Wire not rated for power supply maximum current rating. Wire Size Cross Section (mm 0.75 Resistivity Maximum Length In Meters (Feet)To Limit Voltage Drop To 0.5V Or Less /kft 16.15 (6.19)
-
Page 30: Overvoltage Protection
Either positive or negative voltages can be obtained from the supply by grounding one of the output terminals. It is best to avoid grounding the output at any point other than the power supply output terminals to avoid noise problems caused by common-mode current flowing through the load leads to ground. -
Page 31: Operating Modes
circuits within the supply the power supply output drops to zero and the UNREGULATED indicator turns on. The power supply can be disabled by overvoltage, overtemperature, or by low or high ac line (mains) voltage. Overvoltage. If the voltage across the power supply output terminals rises above a preset level, possibly because of a hardware malfunction, the overvoltage protection (OVP) circuit will trip. - Page 32 crosses the operating locus at point 1. Point 1 is on the part of the operating locus defined by the voltage setting, so the power supply operates in CV mode. Similarly, the line representing load resistance C, the lowest load resistance shown on the graph, crosses the operating locus at point 3.
-
Page 33: Constant Voltage Operation
Constant Voltage Operation By pressing the DISPLAY SETTINGS pushbutton switch you can observe the setting (limits) of both the output voltage and the output current, rather than the actual output values. This you set the current limit when the power supply is operating in CV mode, or set the voltage limit while in CC mode, without having to disconnect or adjust the load. -
Page 34: Constant Current Operation
Constant Current Operation To set up the power supply for constant current operation: With power supply turned off, connect the load to the output terminals. Turn on the power supply. Hold in DISPLAY OVP pushbutton switch and set OVP ADJUST potentiometer for the desired OVP trip voltage. - Page 35 If a sense lead opens there will be a change in the output voltage. See Table 3-4 for the approximate voltage change. Table 3-4. Voltage change due to open sense lead Figure 3-6. Remote Voltage Sensing (2Rs + 0.5)V1 1000 Model 6010A 1.6% -0.1% 6011A 6012B 1.6% -0.1% 6015A 1.6%...
-
Page 36: Analog Programing
Analog Programming These instruments can obtain their output voltage and current programming information from three distinct sources: 1) locally from the front panel, 2) remotely from an external isolated, voltage source or, 3) remotely from an external isolated, resistance. Mode switches B1, B2, .through B6, located on the rear of these products, enable the user to make these selections. -
Page 37: Constant Voltage Output, Voltage Control
Note: If the programming terminals (VP to output voltage will rise above the power supply rating. The supply will not be damaged if this occurs, but the overvoltage trip point should be properly adjusted to protect the user’s load. Figure 3-7. Resistance Programming of Output Voltage Constant Voltage Output, Voltage Control. -
Page 38: Constant Current Output, Resistance Control
Figure 3-9. Optional Voltage Divider for Program Source Constant Current Output, Resistance Control. The setup shown in Figure 3-10 allows the output current to be varied by using an external resistor to program the supply. A programming resistor variable from 0 to 4000 ohms produces a proportional output current from zero to full scale. Note that fixed resistors may be connected in series and/or parallel with the variable programming resistor to set lower and/or upper output current limits. -
Page 39: Constant Current Output, Voltage Control
The power supply can be operated in combination with other power supplies to provide increased output capability. Auto- parallel operation of two power supplies can provide up to twice the output current. Other configurations are possible. Contact Agilent Technologies, Power Products Division for specific application assistance. Auto-Parallel Operation Two units can be connected in an auto-parallel combination to provide twice the output current capability. -
Page 40: Series Operation
= Handle Setting Voltage and Current. Program the slave unit's output voltage above the master's to avoid interference with master- unit CV control. The slave unit's mode switches disable the slave unit's digital current setting from having any effect in auto- parallel operation. -
Page 41: Monitor Signals
Caution: When two supplies are operated in series, they should be programmed to the same voltage to prevent possible damage to the lower voltage supply during short circuit conditions. Contact the factory if this is not possible. = Handle Monitor Signals Amplified and buffered voltage and current monitor output signals are available at the rear-panel terminal strip. -
Page 43: A 100 Vac Input Power Option 100
10.8 Section 2 Manual Changes For Agilent Models 6010A, 6011A, 6012B and 6015A: On page 23 under “AC line Impedance Check”, where the maximum output voltages are tabulated, change the voltages as shown below: 6010A change 65 V to 50 V 6011A change 8 V to 6 V 6012B change 22 V to 13.5 V... -
Page 44: Section 3 Manual Changes
Section 3 Manual Changes On page 30 under “Overvoltage Protection”, change 107% to 90%. On page 36 under “Analog Programming”, in the 3rd paragraph, change the second sentence to read: “A resistance of 0 to 3.33 K ohms programs the output voltage from 0 to full scale and a resistance of 0 to 4 K ohms programs the output current from 0 to full scale.”. -
Page 45: Index
Index airflow...17 ampacity- wire ...29 capacitor load-bypass ...30 CC indicator...26 CC mode...26, 32, 34, 40 circuit breaker ...19 CV indicator ...26 CV mode...26, 32, 33, 40 DISPLAY OVP switch ...26 DISPLAY SETTINGS switch ...26 fuse - line ...21 ground - earth...19, 20, 26 impedance - output ...16 jumpers ...20, 21 line impedance - excessive...23... - Page 46 remote sensing ...34, 40 +S input (see sense leads) -S input (see sense leads) safety class...3 sense leads ...27, 34 serial number ...11 UNREGULATED indicator ...26, 31 wire length ...29 wire size...29 Index 46...
-
Page 47: Agilent Sales And Support Office
Agilent Sales and Support Office For more information about Agilent Technologies test and measurement products, applications, services, and for a current sales office listing, visit our web site: You can also contact one of the following centers and ask for a test and measurement sales representative. - Page 48 Manual Updates The following updates have been made to this manual since the print revision indicated on the title page. 2/01/00 All references to HP have been changed to Agilent. All references to HP-IB have been changed to GPIB. 9/20/04 The Declaration of Conformity has been updated.