Subscribe to Our Youtube Channel
Related Manuals for prodelin TIER II
Summary of Contents for prodelin TIER II
- Page 1 4096-694 MAY 16, 2005 ASSEMBLY MANUAL Revision - TIER II FEED SYSTEM .89m, .92m, 1.0m .6 F/D ANTENNAS NEC INTERFACE PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658...
- Page 2 4096-694 PRODELIN CORPORATION TIER II FEED SYSTEM 0.6 F/D ANTENNAS NEC INTFC TIER II FEED SYSTEM 0.6 F/D ANTENNAS NEC INTERFACE ORIGINAL RELEASE 05/16/05 REV. DESCRIPTION DATE APPROVED...
- Page 3 4096-694 PRODELIN CORPORATION TIER II FEED SYSTEM 0.6 F/D ANTENNAS NEC INTFC Reflector mount may vary. See instructions included with the reflector mount. TIER II ANTENNA SYSTEM (Transmitter weight: 12-lbs. max)
-
Page 4: Table Of Contents
4096-694 PRODELIN CORPORATION TIER II FEED SYSTEM 0.6 F/D ANTENNAS NEC INTFC TABLE OF CONTENTS SECTION TITLE INTRODUCTION GENERAL INFORMATION UNPACKING & INSPECTION FREIGHT DAMAGE MATERIAL MISSING OR DAMAGED MECHANICAL INSTALLATION TOOLS FEED SUPPORT INSTALLATION FEED SUPPORT ASSY PARTS LIST... -
Page 5: Introduction
GENERAL INFORMATION This manual describes the assembly and installation of Prodelin's Tier II antennas. The Prodelin Tier II system will operate in the Ku-Band frequency with high efficiency and at the same time successfully withstand the effects of the environment. -
Page 6: Mechanical Installation Tools
4096-694 PRODELIN CORPORATION TIER II FEED SYSTEM 0.6 F/D ANTENNAS NEC INTFC MECHANICAL INSTALLATION TOOLS METRIC WRENCH MAX RECOMMENDED HARDWARE SIZE SAE WRENCH SIZE SIZE TORQUE 15 ft-lb. 8mm Bolt 13mm (8.1 n-m) 6 ft-lb. 1/4” Bolt 7/16” (8.1 n-m) 15 in-lb. - Page 7 4096-694 PRODELIN CORPORATION TIER II FEED SYSTEM 0.6 F/D ANTENNAS NEC INTFC ANTENNA PART SPECIFICATION LIST FEED SUPPORT ANTENNA FEED ROD TUBE 0.89M 0250-885 0176-343 0.92M 0250-905 0176-360 1.0M 0250-886 0176-344 1.2M 0250-887 0176-345 2.4M 0250-894 0176-349...
-
Page 8: Feed Support Installation
4096-694 PRODELIN CORPORATION TIER II FEED SYSTEM 0.6 F/D ANTENNAS NEC INTFC FEED SUPPORT ASSEMBLY CAUTION: During the assembly procedure, the sequence of instructions must be followed. DO NOT TIGHTEN ANY HARDWARE UNTIL INSTRUCTED. Refer to the feed support parts list and steps. - Page 9 4096-694 PRODELIN CORPORATION TIER II FEED SYSTEM 0.6 F/D ANTENNAS NEC INTFC Reflector [ 3 ] Feed Rod Feed Rods Detail A Feed Support Tube Reflector Detail B Feed Support Tube Detail C...
-
Page 10: Feed Support Assembly
4096-694 PRODELIN CORPORATION TIER II FEED SYSTEM 0.6 F/D ANTENNAS NEC INTFC SECTION III FEED INSTALLATION FEED ASSEMBLY PARTS LIST – TABLE 3.0 ITEM PART NO. DESCRIPTION 0183-265 51° Ku-band Feed Horn Assembly 0198-120 .926” ID O-ring 8200-010 #6 Internal Tooth Lockwasher 8300-002 #6-32 x 0.50”... -
Page 11: Feed Installation
4096-694 PRODELIN CORPORATION TIER II FEED SYSTEM 0.6 F/D ANTENNAS NEC INTFC FEED INSTALLATION PARTS LIST- TABLE 3.2 ITEM PART NO. DESCRIPTION 0211-969 NEC Adapter Bracket 8041-005 M8-1.25 x 50mm Hex Bolt 8201-101 M8 Flatwasher 8202-067 M8 Lockwasher FEED INSTALLATION... -
Page 12: Maintenance
4096-694 PRODELIN CORPORATION TIER II FEED SYSTEM 0.6 F/D ANTENNAS NEC INTFC SECTION IV MAINTENANCE MAINTENANCE OVERVIEW After installation, the antenna requires only periodic inspection. It is anticipated that maintenance, if required, will be minimal and easily handled by a local or in-house maintenance staff.
Need help?
Do you have a question about the TIER II and is the answer not in the manual?
Questions and answers