Related Manuals for Living & Co Waipoua
Summary of Contents for Living & Co Waipoua
- Page 1 Waipoua 5 Drawer Tallboy 103cm 103cm 39.6cm INSTRUCTION MANUAL Maximum recommended weight is 15kgs per drawer Job no.
-
Page 2: Assembly Details
Assembly Details Floor Area 3m x 4m Required Assembly Space Approximate Assembly Time 2 Person Assembly Tools Required AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858... -
Page 3: Care And Maintenance
Tips before you start 1. For the protection of your furniture, we recommend that the product is placed on a protected surface during assembly to prevent damage 2. Please check that all parts are present before you start the assembly of your furniture 3. -
Page 4: Parts List
Parts List PART MEASUREMENTS NOTES 1030 x 396 x 25mm Laminate on one side LH End 922 x 370 x 15mm Laminate on one side (green mark on back) RH End 922 x 370 x 15mm Laminate on one side (red mark on the back) Division 194 x 354 x 15mm Plain (unfinished) - Page 5 Cam Installation & Operation Guide The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this system works. Press the cam fitting into the hole provided. The arrow on the top of the cam must point to the connecting hole in the edge of the board.
- Page 6 Assembly STEP 1: Top • To begin assembly, lay the top finished side down on a clean and clear surface. • Screw six Connecting Bolts into the holes as shown. • Using the Panhead screw, attach the Safety Strap as shown by screwing it first through the Washer and then through the eyelet in the Strap, into the hole in the left-hand side of the Top.
- Page 7 STEP 2: Screw Legs to LH End • Screw the legs onto the LH end using the 31mm gold screws. Ensure the guide holes in the end match up with the guide holes on the leg before inserting the screws. •...
- Page 8 STEP 3: Screw Legs to RH End • Repeat the previous step with the RH End. Nail on Glide Large Woodscrew Screw Finished Edge Large Woodscrew Large Woodscrew screw screw Nail on Glides AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858...
- Page 9 STEP 4: Hardware LH End • Screw the LH Cabinet Drawer Slides into the LH End using two Drawer Slide Screws for each. slide (ensure that the end of the slide with the wheel is on the side with the finished edge). •...
- Page 10 STEP 5: Hardware RH End • Repeat the previous step with the RH End. Large Cam Connecting Bolt Drawer Slide Dowel Screw Dowel Finished Edge Connecting Bolt Drawer Slide Screw Connecting Bolt Drawer Slide Screw Connecting Bolt AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858...
- Page 11 STEP 6: Division • Install the hardware in the Division as shown below. NOTE: The holes for the Cams could be on either side of the Division. • Screw a LH Drawer Slide (CL) on using the Drawer Slide Screws. Ensure that the end of the slide with the wheel faces towards the Finished edge of the Division.
- Page 12 STEP 7: Rail and Shelf Your pack will contain the following rails a base shelf. • 1 x Back Rail • 3 x Front Rails • 1 x Base Shelf • Install the Large Cams into each piece as indicated. •...
- Page 13 STEP 8: Attach Rails & Shelf to LH End • Lay the LH End finished side down on a clean surface that is free of anything that may damage the woodgrain finish. A clean carpeted floor is the most ideal for this. •...
- Page 14 STEP 9: Attach RH End • Fit the RH End to the Rails and Shelf as shown in the drawing below. Ensure the cams on the back rail are facing the top of the unit. • Lock the RH End to the Rails and Shelf by tightening all the Cams in a clockwise direction. Ensure you don’t over tighten them, or this may split the side of the rail.
- Page 15 STEP 10: Attach Division to Top • Lay the Top on a clean, clear surface • Attach the Division to the Top by fitting it down over the Connecting Bolts installed in the Top. Make sure the Finished edge of the Division faces the front of the Top. •...
- Page 16 STEP 11: Attach Top • Lay the assembled Ends connected with Rails and Shelf on its back as shown below, then connect the top with the division to the ends. The Connecting Bolts in the Top will fit down into the Cams in the Ends.
- Page 17 STEP 12: Back Panel • Turn the Tallboy onto its front edge. Make sure the surface is clear and free of anything that may damage the laminate finish. • Slide the Back Panel in place (please ensure that the end with the predrilled holes part way down the panel is at the top) •...
- Page 18 Assemble the Small Drawers Your Waipoua Tallboy will have two shallow top drawer and four deeper bottom drawers. Begin with assembling the small drawers. Drawer Bottom LH Drawer Side Drawer Back RH Drawer Side Drawer Front STEP 13: Install Hardware...
- Page 19 STEP 14: Assemble the Drawer • Lay the Drawer Front finishes side down on a smooth, clean surface. • Attach the LH and RH Drawer Sides by fitting them into place over the Connecting Bolts installed in the Drawer Front. •...
- Page 20 STEP 15: Attach the Drawer Slides • Turn the drawer upside-down as shown and attached the Drawer Slides (DL and DR) with the four small woodscrews as shown below. Ensure that the ends of the slides without the wheels are hard up against the back of the Drawer Front.
- Page 21 STEP 16: Install the Hardware (large drawers) • Install the hardware in the Drawer Parts as shown below. Connecting Bolt Connecting Bolt Connecting Bolt DRAWER FRONT Small Cam DRAWER BOTTOM SUPPORT Dowel Small Small LH DRAWER SIDE Dowel RH DRAWER SIDE STEP 17: Install the Hardware (large drawers) •...
- Page 22 STEP 18: Attach Drawer Back • Fit the Drawer Bottom Support into place underneath the Drawer Bottom, the Connecting Bolt in the centre back of the Drawer Front will fit up into the Small Cam. • Turn the Small Cam in a clockwise direction to lock the Drawer Bottom Support in place. •...
- Page 23 STEP 20: Insert the Drawers • Fit the drawers into the cabinet. The top two drawers are different, one is for the RH side the other the LH so ensure the correct one goes in the correct side. Angle the drawer slightly to ensure that the wheel at the back of the drawer slide goes behind the front wheel on the cabinet slide.
- Page 24 Please note: The is a precautionary measure. The use of tip-over restrains may only reduce but not eliminate, the risk of tip over. Compac Furniture can take no responsibility. Congratulations, your Waipoua 5 Drawer Tallboy is now complete. Thank you for supporting New Zealand Made furniture.
-
Page 28: Warranty
WARRANTY We pride ourselves on producing a range of quality products that are both packed with features and completely reliable. We are so confident in our products, we back them up with a five-year warranty. Now you too can relax knowing that you are covered.