Related Manuals for Living & Co Waipoua Bedside Table
Summary of Contents for Living & Co Waipoua Bedside Table
- Page 1 Waipoua Bedside Table 51cm 55.1cm 39.6cm INSTRUCTION MANUAL Maximum recommended weight 15kgs per drawer Job no.
-
Page 2: Assembly Details
Assembly Details Floor Area 3m x 2m Required Assembly Space Approximate Assembly Time 1 Person Assembly Tools Required AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858... -
Page 3: Care And Maintenance
Tips before you start 1. For the protection of your furniture, we recommend that the product is placed on a protected surface during assembly to prevent damage 2. Please check that all parts are present before you start the assembly of your furniture 3. -
Page 4: Parts List
Parts List PART MEASUREMENTS NOTES 510 x 396 x 25mm Laminate on one side. LH End 446 x 370 x 15mm Laminate on one side. RH End 446 x 370 x 15mm Laminate on one side. Corner Leg 526 x 80 x 25mm Laminate on both sides. - Page 5 Cam Installation & Operation Guide The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this system works. Drawer Slides Guide Your pack will contain two sets of Metal Drawer Slides. These are bundled together with adhesive tape.
- Page 6 Assembly STEP 1: Top • To begin assembly, lay the top finished side down on a clean and clear surface. • Screw four Connecting Bolts into the holes as shown. Connecting Bolt Connecting Bolt Connecting Bolt Connecting Bolt Connecting Bolt AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858...
- Page 7 STEP 2: Screw Legs to LH End • Screw the legs onto the LH end using the 31mm gold screws. Ensure the guide holes in the end match up with the guide holes on the leg before inserting the screws. •...
- Page 8 STEP 3: Screw Legs to RH End • Repeat the previous step with the RH End. Nail on Glide Large Woodscrew Screw Finished Edge Large Woodscrew Nail on Glide AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858...
- Page 9 STEP 4: Hardware LH End • Screw the LH Cabinet Drawer Slides into the LH End using two Drawer Slide Screws for each slide (ensure that the end of the slide with the wheel is on the side with the finished edge). •...
- Page 10 STEP 5: Hardware RH End • Repeat the previous step with the RH End. Connecting Bolt Large Cam Drawer Slide Screw Dowel Finished Edge Connecting Bolt Drawer Slide Screw Connecting Bolt AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858...
- Page 11 STEP 6: Rail and Shelf • Install 2 Dowels and 2 Large Cams into each Rail as shown (ensure the arrow on the top of the Cam points towards the edge of the Rail with the hole in it. Large Cam Dowel Dowel Dowel...
- Page 12 STEP 7: Attach Rails to LH End • Fit the Front Rail over the Connecting Bolt and tighten the cams as shown on page 5, ensure you don’t over tighten them, or this may split the side of the rail. Ensure the finished side of the Rail is facing forward so the cams can’t be seen once the cabinet is completed.
- Page 13 STEP 8: Attach RH End • Fit the Connecting Bolts installed in the RH End into the Cams in the Rails and Base Shelf as shown below. • Tighten the cams as shown on page 5, ensure you don’t over tighten the cams or this may split the side of the rail.
- Page 14 STEP 9: Attach Top • Stand the Bedside upright. • Fit the Top to the Ends by fitting the four Connecting Bolts installed in the Top into the Cams in the Ends. Ensure the unfinished edge is facing towards the back. Tighten all four Cams to lock the Top to the Ends.
- Page 15 STEP 10: Back Panel • Carefully lay the bedside on its front edge. • Slide the Back Panel in place. • Using the two Panhead screws provided, secure the Back Panel in place. Then stand the Bedside upright. Panhead Screw Panhead Screws 9 15 AFTER SALES SUPPORT...
- Page 16 Assemble the Drawers Drawer Bottom LH Drawer Side Drawer Side RH Drawer Side Drawer Front 9 16 AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858...
- Page 17 STEP 11: Install Hardware Connecting Bolt Small Cam Dowell • Install the hardware in the Drawer parts as shown below. Connecting Bolt DRAWER FRONT Dowel Dowel RH DRAWER SIDE LH DRAWER SIDE Note: Be sure that the arrow on the Small Cam points to the end of the drawer side nearest it. 10 17 AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858...
- Page 18 STEP 12: Assemble the Drawer • Lay the Drawer Front finishes side down on a smooth, clean surface. • Attach the LH and RH Drawer Sides by fitting them into place over the Connecting Bolts installed in the Drawer Front. •...
- Page 19 STEP 13: Attach the Drawer Slides • Turn the drawer upside-down as shown and attached the Drawer Slides (DL and DR) with the four small woodscrews as shown below. Ensure that the ends of the slides without the wheels are hard up against the back of the Drawer Front.
- Page 20 STEP 14: Insert the Drawers • Fit the drawers into the Bedside. Make sure that the rollers at the back of the drawer go behind the front rollers in the cabinet and into the channel of the drawer slide. It helps to lift the front of the drawer up a little when doing this.
-
Page 24: Warranty
WARRANTY We pride ourselves on producing a range of quality products that are both packed with features and completely reliable. We are so confident in our products, we back them up with a five-year warranty. Now you too can relax knowing that you are covered.