Related Manuals for Living & Co Takiwira
Summary of Contents for Living & Co Takiwira
- Page 1 Tākiwira Bedside Table 46cm 54.3cm 36.6cm INSTRUCTION MANUAL Maximum recommended weight 15kgs per drawer Job no.
-
Page 2: Assembly Details
Assembly Details Floor Area 3m x 2m Required Assembly Space Approximate Assembly Time 1 Person Assembly Tools Required AFTER SALES SUPPORT www.compacfurniture.co.nz or 0800 100 858... -
Page 3: Care And Maintenance
Tips before you start 1. For the protection of your furniture, we recommend that the product is placed on a protected surface during assembly to prevent damage 2. Please check that all parts are present before you start the assembly of your furniture 3. -
Page 4: Parts List
Parts List PART MEASUREMENTS NOTES 460 x 396 x 25mm Laminate on one side. LH End 518 x 390 x 15mm Laminate on both sides. RH End 518 x 390 x 15mm Laminate on both sides. Top Drawer Front 412 x 195 x 15mm Laminate on one side. - Page 5 Cam Installation & Operation Guide The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this system works. Drawer Slides Guide Your pack will contain two sets of Metal Drawer Slides. These are bundled together with adhesive tape.
- Page 6 Assembly STEP 1: Top To begin assembly, lay the top finished side down on a clean and clear surface • Screw four Connecting Bolts into the holes as shown • Connecting Bolt Connecting Bolt Connecting Bolt Connecting Bolt Connecting Bolt STEP 2: LH End Screw the LH Cabinet Drawer Slides into the LH End using two Drawer Slide Screws for each •...
- Page 7 STEP 3: RH End • Repeat the previous step with the RH End. Connecting Bolt Large Cam Drawer Slide Screw Dowel Dowel Drawer Slide Screw Drawer Slide Screw Finished Edge Connecting Bolt Connecting Bolt STEP 4: Rails • Install 2 Dowels and 2 Large Cams into each Rail as shown (ensure the arrow on the top of the Cam points towards the edge of the Rail with the hole in it.
- Page 8 STEP 5: Attach Rails to LH End Fit the Front Rail (the one with one finished side) over the Connecting Bolt closest to the finished • side of the End as shown (ensure the finished side of the Rail is facing forward so the cams can’t be seen once the cabinet is completed).
- Page 9 STEP 7: Attach Top and Glide Feet Fit the Top to the Ends by fitting the four Connecting Bolts installed in the Top into the Cams in the • Ends. Tighten all four Cams to lock the Top to the Ends. •...
- Page 10 Assemble the Drawers Drawer Bottom LH Drawer Side Drawer Side RH Drawer Side Drawer Front AFTER SALES SUPPORT www.compacfurniture.co.nz or 0800 100 858...
-
Page 11: Drawer Front
STEP 9: Install Hardware Connecting Bolt Small Cam Dowell • Install the hardware in the Drawer parts as shown below. Connecting Bolt DRAWER FRONT Dowel Dowel RH DRAWER SIDE LH DRAWER SIDE Note: Be sure that the arrow on the Small Cam points to the end of the drawer side nearest i AFTER SALES SUPPORT www.compacfurniture.co.nz or 0800 100 858... - Page 12 STEP 10: Assemble the Drawer • Lay the Drawer Front finishes side down on a smooth, clean surface. Attach the LH and RH Drawer Sides by fitting them into place over the Connecting Bolts installed in • the Drawer Front. Turn the Small Cams in a clockwise direction to lock the Drawer Sides in place.
- Page 13 STEP 11: Attach the Drawer Slides Turn the drawer upside-down as shown and attached the Drawer Slides (DL and DR) with the four • woodscrews as shown below. Ensure that the ends of the slides without the wheels are hard up against the back of the Drawer Front.
- Page 14 STEP 12: Attach the Handle and Insert the Drawers • Attach the Bar Handle to the Drawer Front using the screws provided • Fit the drawers into the Bedside. Make sure that the rollers at the back of the drawer go behind the front rollers in the cabinet and into the channel of the drawer slide.
-
Page 15: Warranty
WARRANTY We pride ourselves on producing a range of quality products that are both packed with features and completely reliable. We are so confident in our products, we back them up with a five-year warranty. Now you too can relax knowing that you are covered.