Related Manuals for Living & Co Waipoua
Summary of Contents for Living & Co Waipoua
- Page 1 Waipoua 6 Drawer Lowboy 118.3cm INSTRUCTION MANUAL Maximum recommended weight 15kgs per drawer 79.4cm 39.6cm INSTRUCTION MANUAL Maximum recommended weight is 15kgs per drawer Job no.
-
Page 2: Assembly Details
Assembly Details Floor Area 3m x 4m Required Assembly Space Approximate Assembly Time 2 Person Assembly Tools Required AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858... -
Page 3: Care And Maintenance
Tips before you start 1. For the protection of your furniture, we recommend that the product is placed on a protected surface during assembly to prevent damage 2. Please check that all parts are present before you start the assembly of your furniture 3. -
Page 4: Parts List
Parts List PART MEASUREMENTS NOTES 1183 x 396 x 25mm Laminate on one side. LH End 684 x 370 x 15mm Laminate on one side (green mark on back). RH End 684 x 370 x 15mm Laminate on one side (red mark on back). Base Shelf 1091 x 352 x 15mm Plain (unfinished). -
Page 5: After Sales Support
Cam Installation & Operation Guide The Cam and Connecting Bolt system is used to put your unit together. Below is an explanation of how this system works. Drawer Slides Guide Your pack will contain six sets of Metal Drawer Slides. These are bundled together with adhesive tape. - Page 6 Assembly STEP 1: Top • To begin assembly, lay the top finished side down on a clean and clear surface. • Screw six Connecting Bolts into the holes as shown. • Using the Panhead screw, attach the Safety Strap as shown by screwing it first through the Washer and then through the eyelet in the Strap, into the hole in the left-hand side of the Top.
- Page 7 STEP 2: Screw Legs to LH End • Screw the legs onto the LH end using the 31mm gold screws. Ensure the guide holes in the end match up with the guide holes on the leg before inserting the screws. •...
- Page 8 STEP 3: Screw Legs to RH End • Repeat the previous step with the RH End. Nail on Glide Large Woodscrew Screw Finished Edge Large Woodscrew Large Woodscrew Nail on Glide AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858...
- Page 9 STEP 4: Hardware LH End • Screw the LH Cabinet Drawer Slides into the LH End using two Drawer Slide Screws for each slide (ensure that the end of the slide with the wheel is on the side with the finished edge). •...
- Page 10 STEP 5: Hardware RH End • Repeat the previous step with the RH End. Large Cam Connecting Bolt Drawer Slide Dowel Screw Dowel Finished Edge Drawer Slide Screw Connecting Bolt Drawer Slide Screw Connecting Bolt AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858...
- Page 11 STEP 6: Division • Install the hardware in the Division as shown below. NOTE: The holes for the Cams could be on either side of the Division. • Repeat this step for both sides of the division. Ensure that the end of the slide with the wheel faces towards the Finished edge of the Division.
- Page 12 STEP 7: Rail and Shelf Your pack will contain the following rails a base shelf. • 4 x Front Rails • 1 x Base Shelf • Install the Large Cams into each piece as indicated. • Push the Dowels into each of the boards as indicated. Dowel Large Cam Dowels...
- Page 13 STEP 8: Attach LH End to Top • Lay the Top on a clean, clear surface. • Attach the LH End to the Top by fitting it down over the Connecting Bolts installed in the Top. Make sure the Finished edge of the LH End faces the front of the Top. Then tighten the cams as show on page 5.
- Page 14 STEP 9: Attach Division to Top • Attach the Division to the Top by fitting it down over the Connecting Bolts installed in the Top. Make sure the Finished edge of the Division faces the front of the Top. Then tighten the cams as show on page 5.
- Page 15 STEP 10: Fit the Base Shelf • Install the Base Shelf by fitting the shelf into Connecting Bolts in the LH end as shown below. Ensure the finished edge of the shelf is facing forward, then tighten the cams as show on page 5. Base Shelf Finished Edge AFTER SALES SUPPORT...
- Page 16 STEP 11: Attach RH End to Top • Attach the RH End to the Top by fitting it down over the Connecting Bolts installed in the Top. Also insert the connecting bolts in the ends of the front rails and base shelf. Then tighten the cams as show on page 5.
- Page 17 STEP 12: Back Panel • Slide the Back Panel in place. • Using eight Panhead screws provided, secure the Back Panel in place using the predrilled holes in the back panel. Then stand the Lowboy upright. Panhead Screw Panhead Screws Panhead Screws AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858...
-
Page 18: Drawer Front
Assemble the Drawers Drawer Bottom LH Drawer Side Drawer Side RH Drawer Side Drawer Front STEP 13: Install Hardware Connecting Bolt Small Cam Dowell • Install the hardware in the Drawer parts as shown below. Connecting Bolt DRAWER FRONT Dowel Dowel RH DRAWER SIDE LH DRAWER SIDE... - Page 19 STEP 14: Assemble the Drawers • Lay the Drawer Front finishes side down on a smooth, clean surface. • Attach the LH and RH Drawer Sides by fitting them into place over the Connecting Bolts installed in the Drawer Front. •...
- Page 20 STEP 15: Attach the Drawer Slides • Turn the drawer upside-down as shown and attached the Drawer Slides (DL and DR) with the four small woodscrews as shown below. Ensure that the ends of the slides without the wheels are hard up against the back of the Drawer Front.
- Page 21 STEP 16: Insert the Drawers • Fit the drawers into the Lowboy. Make sure that the rollers at the back of the drawer go behind the front rollers in the cabinet and into the channel of the drawer slide. It helps to lift the front of the drawer up a little when doing this.
- Page 22 Please note: The is a precautionary measure. The use of tip-over restrains may only reduce but not eliminate, the risk of tip over. Compac Furniture can take no responsibility. Congratulations, your Waipoua 6 Drawer lowboy is now complete. Thank you for supporting New Zealand Made furniture.
- Page 23 AFTER SALES SUPPORT support@compacfurniture.co.nz or 0800 100 858...
-
Page 24: Warranty
WARRANTY We pride ourselves on producing a range of quality products that are both packed with features and completely reliable. We are so confident in our products, we back them up with a five-year warranty. Now you too can relax knowing that you are covered.