Hotpoint CIC 642 C Operating Instructions Manual page 3

i ing i ing
The appliance must be installed The appliance must be installed
supporting surface. supporting surface.
Any deformities caused by improper fixing could affect Any deformities caused by improper fixing could affect
the features and operation of the hob. the features and operation of the hob.
The thickness of the supporting surface The thickness of the supporting surface
taken into account when choosing taken into account when choosing
screws for the fixing hooks: screws for the fixing hooks:
• 30 mm thick: 23 mm screws • 30 mm thick: 23 mm screws
• 40 mm thick: 13 mm screws • 40 mm thick: 13 mm screws
.ix the hob as follows: .ix the hob as follows:
1. Use short flat-bottomed screws to fix the 4 1. Use short flat-bottomed screws to fix the 4
alignment springs in the holes provided at the central alignment springs in the holes provided at the central
point of each side of the hob. point of each side of the hob.
2. Place the hob in the cavity, make sure it is in a 2. Place the hob in the cavity, make sure it is in a
central position and push down on the whole perimeter central position and push down on the whole perimeter
until the hob is stuck to the supporting surface. until the hob is stuck to the supporting surface.
3. .or hobs with raised sides: After inserting the hob 3. .or hobs with raised sides: After inserting the hob
into its cavity, insert the 4 fixing hooks (each has its into its cavity, insert the 4 fixing hooks (each has its
own pin) into the lower edges of the hob, using the own pin) into the lower edges of the hob, using the
long pointed screws to fix them in place, until the long pointed screws to fix them in place, until the
glass is stuck to the supporting surface. glass is stuck to the supporting surface.
The screws for the alignment springs must remain The screws for the alignment springs must remain
 
accessible. accessible.
In order to adhere to safety standards, the appliance In order to adhere to safety standards, the appliance
 
must not come into contact with electrical parts once it must not come into contact with electrical parts once it
has been installed. has been installed.
All parts which ensure the safe operation of the All parts which ensure the safe operation of the
 
appliance must not be removable without the aid of a appliance must not be removable without the aid of a
tool. tool.
lectrical connection lectrical connection
  The electrical connection for the hob and for any built- The electrical connection for the hob and for any built-
in oven must be carried out separately, both for safety in oven must be carried out separately, both for safety
purposes and to make extracting the oven easier. purposes and to make extracting the oven easier.
Single-phase connection Single-phase connection
The hob is equipped with a pre-connected electricity The hob is equipped with a pre-connected electricity
supply cable, which is designed for single-phase supply cable, which is designed for single-phase
connection. Connect the wires in accordance with the connection. Connect the wires in accordance with the
instructions given in the following table and diagrams: instructions given in the following table and diagrams:
Voltage and Voltage and
Electrical cable Electrical cable
mains frequency mains frequency
220-240V 1+N ~ 220-240V 1+N ~
50 Hz 50 Hz
Other types of connection Other types of connection
If the mains supply corresponds with one of the If the mains supply corresponds with one of the
following: following:
on a perfectly level on a perfectly level
should be should be
the length of the the length of the
Wire connection Wire connection
: yellow/green; : yellow/green;
N: the two blue wires N: the two blue wires
together together
L: brown and black L: brown and black
together together
Voltage and mains frequency Voltage and mains frequency
• 400V - 2+N ~ 50 Hz • 400V - 2+N ~ 50 Hz
• 220-240V 3 ~ 50 Hz • 220-240V 3 ~ 50 Hz
• 400V 3 - N ~ 50 Hz • 400V 3 - N ~ 50 Hz
• 400V - 2+2N ~ 50 Hz • 400V - 2+2N ~ 50 Hz
Separate the wires and connect them in accordance Separate the wires and connect them in accordance
with the instructions given in the following table and with the instructions given in the following table and
diagrams: diagrams:
Tensión tipo y Tensión tipo y
Cable eléctrico Cable eléctrico
frecuencia de la red frecuencia de la red
400V - 2+N ~ 400V - 2+N ~
50 Hz 50 Hz
220-240V 3 ~ 220-240V 3 ~
50Hz 50Hz
400V 3-N~ 50Hz 400V 3-N~ 50Hz
400V - 2+2N ~ 400V - 2+2N ~
50 Hz 50 Hz
Connecting the electricity supply ca le to the mains Connecting the electricity supply ca le to the mains
If the appliance is being connected directly to the If the appliance is being connected directly to the
electricity mains an omnipolar switch must be installed electricity mains an omnipolar switch must be installed
with a minimum opening of 3 mm between contacts. with a minimum opening of 3 mm between contacts.
The installer must ensure that the correct electrical The installer must ensure that the correct electrical
 
connection has been made and that it is fully connection has been made and that it is fully
compliant with safety regulations. compliant with safety regulations.
Before connecting the appliance to the power supply, Before connecting the appliance to the power supply,
make sure that: make sure that:
• The appliance is earthed and the plug is compliant • The appliance is earthed and the plug is compliant
with the law. with the law.
• The socket can withstand the maximum power of the • The socket can withstand the maximum power of the
appliance, which is indicated on the data plate appliance, which is indicated on the data plate
located on the appliance itself. located on the appliance itself.
• The voltage falls within the range of values indicated • The voltage falls within the range of values indicated
on the data plate. on the data plate.
• The socket is compatible with the plug of the • The socket is compatible with the plug of the
appliance. If the socket is incompatible with the appliance. If the socket is incompatible with the
plug, ask an authorised technician to replace it. Do plug, ask an authorised technician to replace it. Do
not use extension cords or multiple sockets. not use extension cords or multiple sockets.
Once the appliance has been installed, the power Once the appliance has been installed, the power
 
supply cable and the electrical socket must be easily supply cable and the electrical socket must be easily
accessible. accessible.
  The cable must not be bent or compressed. The cable must not be bent or compressed.
The cable must be checked regularly and replaced The cable must be checked regularly and replaced
 
by authorised technicians only. by authorised technicians only.
The manufacturer declines any lia ility should The manufacturer declines any lia ility should
 
these safety measures not e o served these safety measures not e o served
 Do not remove or replace the power supply cable for  Do not remove or replace the power supply cable for
any reason. Its removal or replacement will void the any reason. Its removal or replacement will void the
warranty and the CE marking. INDESIT does not warranty and the CE marking. INDESIT does not
assume liability for accidents or damage arising from assume liability for accidents or damage arising from
replacement/removal of the original power supply replacement/removal of the original power supply
cable. Replacement can only be accepted when cable. Replacement can only be accepted when
carried out by personnel authorised by INDESIT and carried out by personnel authorised by INDESIT and
using an original spare part. using an original spare part.
GB GB
Conexión de los cables Conexión de los cables
: amarillo/verde; : amarillo/verde;
N: los 2 cables azules juntos N: los 2 cables azules juntos
L1: negro L1: negro
L2: marrón L2: marrón
: amarillo/verde; : amarillo/verde;
N1: azul N1: azul
N2: azul N2: azul
L1: negro L1: negro
L2: marrón L2: marrón
3 3