THANK YOU Dear Valued Customer, SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. All SUMERAIN products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions.
If a defect is found in normal residential use, SUMERAIN will, at its election, repair, provide a replacement part or product, or make appropriate adjustment.
Page 4
Ceramic Disc Valve Valve Body Material Brass Spout Material Stainless steel Spout Net Weight 2.86lbs Gross Weight 8.90lbs Working water press 0.2 ~0.8 Mpa Spout Flow Rate 9.59GPM Packing box size 16-11/32’’ x 11-7/32” x 4-1/8” SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 5
DIMENSION Front view of faucet Side view of faucet SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 6
SIDE VIEW OF SPOUT SIDE VIEW OF CONTROL VALVE SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
1PCS 2138035 2138036 Shower hose 1PCS G1/2’’ hose(40cm) 1PCS 2138037 2138038 G3/8’’ hose 2PCS 2138039 If any of these items are missing, please contact SUMERAIN consumer service at +1 866 203 0866 or email to: supports@sumerain.com SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 8
4. INSTALLATION HOLES INSPECTION Verify that the hole sizes and positions on the deck are correct, the optimal diameter of mounting hole optional is 32mm(1-1/4”),the max deck thickness is 32mm(1-1/4”) . SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
5.1 Turn on your shut-off valve for cleaning the hot and cold water supply pipe before connect to the faucet, allow the water flush 3~5 minutes to flush out dirt and debris. Shut off the water supply again after finish. 5.2 Disassemble diverter valve assembly. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 10
5.4 Attach and Install the diverter knob to diverter rod. 5.5 Position spout onto the hole of mounting surface, attach rubber washer on spout shank and fasten with shank locknut by wrench and screw driver from underneath. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 11
5.6 Attach the tee to diverter valve body. 5.7 Fasten the tee with locknut. 5.8 Install the hand shower hose adapter to diverter valve body. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 12
5.9 Screw in the hoses to the bottom of control valve as below drawing Bottom view of control valve Hoses connection SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 13
Place control valve with hoses across the mounting surface, secure it with lock nut by screwdriver. 5.10 Place shower holder assembly across the mounting surface, secure it with lock nut by wrench. 5.11 SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 14
Connect control valve outlet to spout diverter valve inlet with hose. 5.12 5.13 Screw the hand shower in the hand shower adapter. Please don’t forget to put into the rubber washer for leaking proof. 5.14 Connect shower hose to the diverter valve outlet as drawing. SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 15
5.15 Install the hand shower into the end of shower hose with correct position. 5.15 Connect all components with flexible hose. 6. INSPECTION 6.1 Turn on hold and cold water supply and check all connection for ensuring no leaking anywhere. INSTALL FINISH SUMERAIN SANITARY GROUP WWW.SUMERAIN.COM...
Page 16
Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage. Components with damaged surfaces must be replaced or injury could result. Damage caused by improper treatment is not covered under the warranty. HONGKONG SUMERAIN SANITARY INDUSTRY CO., LIMITED Address: ROOM 1018, HOLLYWOOD PLAZA 610 NATHAN ROAD MONGKOK, KL,HONGKONG...
Need help?
Do you have a question about the S2138XW and is the answer not in the manual?
Questions and answers