Related Manuals for SUMERAIN S2139 Series
Summary of Contents for SUMERAIN S2139 Series
- Page 1 MODEL:S2139XX Version: V3.1 MODEL FINISH S2139CH CHROME S2139NB BRUSHED NICEKL S2139OB OIL RUBBER BRONZE S2139MB MATTE BLACK S2139BG BRUSHED GOLD...
- Page 2 Dear Valued Customer, SUMERAIN would like to take this opportunity to thank you for purchasing SUMERAIN products. It is our sincere hope that you are completely satisfied with your new purchase. All SUMERAIN products are carefully engineered, and factory tested to provide long trouble-free use under normal conditions. This product is easy to install using basic tools and our easy to follow illustrated instructions.
- Page 3 This warranty covers only your SUMERAIN manufactured product. SUMERAIN warrants this product against defects in material or workmanship as follows: SUMERAIN will repair at no charge for parts only or, at its option, replace any product or part of the product that proves defective because of improper workmanship and/or material, under normal installation, use, service and maintenance.
- Page 4 Function Bathtub faucet Floor mounted, Freestanding Feature Theme Modern ,Contemporary Chrome/Brushed Nickel/Matte Black/ Oil Rubber Bronze/Brushed Gold Finish Number of Handles Level Handle style Primary Material Brass Mounting Hardware Included Diverter Included Handheld Shower Included Valve Included Hand shower material Brass Shower hose Included Hose Material...
- Page 5 FRONT VIEW OF FAUCET...
- Page 6 RIGHT VIEW OF FAUCET...
-
Page 7: Before Proceeding
Allen wrench S4 1PCS Hand shower 1PCS 2139019 2139020 washer 1PCS Hand shower adapter 1PCS 2139021 2139022 Shower hose 1PCS 1PCS 2139023 2139024 Standpipe If any of these items are missing, please contact SUMERAIN consumer service by email to: supports@sumerain.com... - Page 8 4. ROUGH-IN VALVE INSTALLATION 4.1 INSTALL TUB FILLER FLOOR SUPPORT 4.1.1 Adequate floor support is required. The wood support must be a minimum of 1-3/16" (30 mm) thick by 9-27/32" (250 mm) wide. 2”x6” lumber is not adequate for this application. 4.1.2 Locate wood support between floor joists keeping a minimum distance of 2-3/4"...
- Page 9 4.2 INSTALL HOT AND COLD WATER SUPPLIES. Apply sealing tape to threaded connections. Thread supply assemblies into rough-in valve inlets. The Hot inlet will be on the left when facing the front of the Tub Filler. Note: （1）The Hot and Cold inlets are marked on the concealed box. （2）G1/2 Male to NPT 1/2-14 Male adapter may be required in North America.
- Page 10 4.4 Drill four pilot holes of 13/32" [10 mm] in diameter Cold 4.5 Install the 4 mounting screws into wood support and install rough-in valve onto the 4 mounting screws and tighten nuts & washers supplied Cold Cold...
- Page 11 Cold 4.6 LEVEL ROUGH-IN VALVE(CONCEALED BOX) Check that top of the rough-in valve is level in all directions. If the rough-in valve is not level follow the steps below. (1) Loosen the four mounting nuts(2b). (2) Adjust until the concealed box is level in all directions. (3) Tighten the four mounting nuts(2b) Verify that the concealed box is level and then fully tighten nuts before next step.
- Page 12 4.8 Install the Drain Pipe Adapters with the inner hexagon screw. Cold 4.9 Connect the supplied Drain Pipe to Drain Pipe Adapters and turn on the water supplies to flush 3~5 minutes to flush out dirt and debris. Cold...
- Page 13 5.0 (a) Shut off the water supply and keep the Drain Pipe on Drain Pipe Adapters for dust-proof during further installation. Cold (b) Optional Step : Remove the Drain Pipe Adapters and cover the conceal box with dust cover(not provide) Cold...
- Page 14 Cold 5.1 Done the finished floor. Cold...
- Page 15 5.2 Cut excess section of concealed box above the finished floor if necessary.
- Page 16 5.3 Install the Hot/Cold Brass Supply riser to faucet body assembly. 5.4 Install the standpipe to faucet body assembly.
- Page 17 5.5 Place the escutcheon over the standpipe. 5.6 Install the mounting base to standpipe and fasten it.
- Page 18 5.7 Remove the Drain Pipe Adapters and the Drain Pipe or the dust cover from the concealed box. 5.8 Align the hot&cold water brass risers and insert into the rough-in valve. Cold...
- Page 19 5.9 Install the mounting screws and fasten them. 5.10 Adjusting faucet spout to desired direction by rotating spout.
- Page 20 5.11 Plush the escutcheon to the finished floor. 5.12 Install the hand shower to the hand shower adapter.
- Page 21 5.13 Connect one end of the shower hose to the mixer outlet and the other end to the hand shower adapter. Ensure the washer is in each end for seal. 5.14 Assemble finished. 6. INSPECTION 6.1 Turn on hold and cold water supply and check all connection for ensuring no leaking anywhere. INSTALL FINISH...
- Page 22 Please note: if the surface is already damaged, the effect of cleaning materials will cause further damage. Components with damaged surfaces must be replaced or injury could result. Damage caused by improper treatment is not covered under the warranty. HONGKONG SUMERAIN SANITARY INDUSTRY CO., LIMITED Address: ROOM 1018, HOLLYWOOD PLAZA 610 NATHAN ROAD MONGKOK, KL,HONGKONG Factory Address: Floor 3th,No.2 ZhongXing Road,ShuiNuan City Industrial Zone,Shuikou town, Kaiping City,...
Need help?
Do you have a question about the S2139 Series and is the answer not in the manual?
Questions and answers