DeWalt DCD805 Original Instructions Manual
Hide thumbs
Also See for DCD805:
- User manual ,
- Instruction manual (37 pages) ,
- Original instructions manual (17 pages)
Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for DeWalt DCD805
Summary of Contents for DeWalt DCD805
- Page 1 DCD800 DCD805...
- Page 2 English (original instructions) Copyright D WALT...
- Page 3 Fig. A Fig. B XXXX XX XX...
- Page 4 Fig. C Fig. D Fig. E...
-
Page 5: Technical Data
Maximum drilling capacity Wood Metal Drill/Impact Drill Masonry — DCD800, DCD805 Weight (without battery pack) 1.28 1.34 WALT declares that these products described under Technical Data are in compliance with: Noise values and/or vibration values (triax vector sum) according to 2006/42/EC, EN62841‑1:2015, EN62841‑2‑1:2018+A11:2019. -
Page 6: Definitions: Safety Guidelines
Please read the manual and pay attention to these symbols. DANGER: Indicates an imminently hazardous DRILL/IMPACT DRILL situation which, if not avoided, will result in death or DCD800, DCD805 serious injury. WALT declares that these products described under Technical WARNING: Indicates a potentially hazardous situation Data are in compliance with: which, if not avoided, could result in death or The Supply of Machinery (Safety) Regulations, 2008, S.I. -
Page 7: Work Area Safety
English 1) Work Area Safety e ) Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool a ) Keep work area clean and well lit. Cluttered or dark in unexpected situations. areas invite accidents. -
Page 8: Residual Risks
English b ) Use power tools only with specifically designated to bend if allowed to rotate freely without contacting the battery packs. Use of any other battery packs may create workpiece, resulting in personal injury. a risk of injury and fire. • Always start drilling at low speed and with the bit tip c ) When battery pack is not in use, keep it away from in contact with the workpiece. -
Page 9: Important Safety Instructions For All Battery Chargers
English If the supply cord is damaged, it must be replaced only by • Pull by plug rather than cord when disconnecting WALT or an authorised service organisation. charger. This will reduce risk of damage to electric plug and cord. Mains Plug Replacement •... -
Page 10: Charger Cleaning Instructions
English Charger Cleaning Instructions Charge Indicators WARNING: Shock hazard. Disconnect the charger Charging from the AC outlet before cleaning. Dirt and grease may be removed from the exterior of the charger using a Fully Charged cloth or soft non‑metallic brush. Do not use water or any cleaning solutions. -
Page 11: Storage Recommendations
English Use Mode: When the FLEXVOLT may result. Damaged battery packs should be returned to battery stands alone or is in service centre for recycling. WALT 18V product, it will operate as an 18V battery. When the FLEXVOLT battery is in a 54V or a 108V (two 54V batteries) WARNING: Fire hazard. -
Page 12: Package Contents
Battery Type Description (Fig. A) The following tools operate on a 18 volt battery pack: DCD800, DCD805. WARNING: Never modify the power tool or any part of it. These battery packs may be used: DCB181, DCB182, DCB183, Damage or personal injury could result. -
Page 13: Assembly And Adjustments
English ASSEMBLY AND ADJUSTMENTS The belt hook and magnetic bit holder can be be attached to either side of the tool using only the screw provided, to WARNING: To reduce the risk of serious personal accommodate left‑ or right‑ handed users. If the hook or injury, turn tool off and disconnect battery pack magnetic bit holder is not desired at all, it can be removed from before making any adjustments or removing/... -
Page 14: Operation
English Pivoting LED Worklight (Fig. A, E) anticlockwise (as viewed from the front) far enough to accept the desired accessory. CAUTION: Do not stare into worklight. Serious eye 3. Insert the accessory about 19 mm into the chuck and injury could result. tighten securely by rotating the chuck sleeve clockwise The worklight ... -
Page 15: Maintenance
Lubrication Hammerdrill Operation (Fig. A, D) Your power tool requires no additional lubrication. DCD805 only 1. Turn the collar 3 to the hammerdrill symbol. 2. Select the high speed setting by sliding the gear shifter ... - Page 16 English • Run the battery pack down completely, then remove it from the tool. • Li‑Ion cells are recyclable. Take them to your dealer or a local recycling station. The collected battery packs will be recycled or disposed of properly.
- Page 20 Belgique et WALT ‑ Belgium BVBA Tel: NL 32 15 47 37 63 www.dewalt.be luxembourg België en luxemburg enduser.BE@sBDinc.com Egide Walschaertsstraat 16 Tel: FR 32 15 47 37 64 2800 Mechelen Fax: 32 15 47 37 99 Danmark WALT (Stanley Black&Decker AS)