Page 1
Service Manual Ver. 1 Network Audio Receiver NR1200 Click here! On-line service parts list http://dmedia.soundunited.com/documents/details/26046 ONLINE PARTS LIST (P5) WEB owner’s manual http://manuals.marantz.com/NR1200/NA/EN/index.php http://manuals.marantz.com/NR1200/EU/EN/index.php http://manuals.marantz.com/NR1200/JP/JA/index.php Upload is planned for the time of a future press release. BEFORE SERVICING THIS UNIT...
Page 2
BEFORE SERVICING THIS UNIT SAFETY PRECAUTIONS NOTE FOR SCHEMATIC DIAGRAM HANDLING THE SEMICONDUCTOR AND OPTICS ONLINE PARTS LIST Accessing the Parts List Searching Part Numbers or Ref. Numbers NOTE FOR PARTS LIST SERIAL NUMBER Serial Number Organization SKU Code of this Unit POST-SERVICE PRECAUTIONS Initializing this Unit JIG FOR SERVICING...
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. Leakage current check Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer. CAUTION: Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
On-line service parts list http://dmedia.dmglobal.com/Document/DocumentDetails/XXXXX ONLINE PARTS LIST (P5) WEB owner’s manual http://manuals.marantz.com/AAAAA/NA/EN/index.php http://manuals.marantz.com/AAAAA/EU/EN/index.php http://manuals.marantz.com/AAAAA/AP/ZH/index.php Upload is planned for the time of a future press release. BEFORE SERVICING THIS UNIT NOTE : If the web browser does not open automatically, copy the URL and paste it into the address bar (3) Next, click the "Sheet"...
Page 6
The 14-digit serial number that contains the code of the manufacturing plant and the manufacturing date. 14 digits Factory Manufactured Cumulative Year, month code code serial number The last Month 2digit of year (01 ~ 12) SKU Code of this Unit Product SKU SKU Code NR1200/U1B NR1200/N1B NR1200/N1SG NR1200/FN...
POST-SERVICE PRECAUTIONS Initializing this Unit Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB. 1. Press the power button to turn off the power. 2. While holding down buttons "ZONE2 SOURCE" and "TUNER PRESET CH -" simultaneously, press the power button to turn on the power.
Page 14
SCH06 CPU LEVEL CHG DIGITAL 5/11 TO 1D TO A4 TO A8 TO 2D (CPU LEVEL CHG) TO DIGITAL CNT MN864787 MN864788 MAIN DAC STBY3.3V STBY5V FROM SWM3.3V D.SUPPLY M3.3V DGND TO 3D CEC_COM C1212 OPEN-1005 SWM3.3V R1094 CEC_OUT Q1057 2SD2114K R1098 100K...
Page 15
SCH07 DSP TO 4D TO 5D TO C4 TO C2 DIGITAL 9/11 FROM FROM DIR/A.PLD NET PHY (DSP) MP:OPEN DSP1CS DSP1MISO DSP1MOSI DSP1CLK DGND DA3.3V Q2203 RT1N141C 11 12 13 14 15 16 R2119 DSP input DATA MP:OPEN I2S(HD Audio) I2S(PCM Multi) DSP1INF/FL I2S0...
Page 16
SCH08 DIR, A.PLD DIGITAL 7/11 TO C0 TO C5 TO 6D TO B2 TO B9 TO C3 (DIR/A.PLD) FROM FROM NET PHY MN864788 NET PHY NET PHY MAIN DAC (1) DIR input CH1:COAX.1 (RXIN0) *FILTER COMPONENTS VALUE TYPE TOLERANCE RT1N141C Q2204 R1907 680 OHM...
SCH09 MAIN DAC DIGITAL 8/11 (MAIN DAC) TO D2 TO D9 TO D6 TO D7 FROM DIR/A.PLD DIR/A.PLD TO 1E DA+5V AD_VDCOM ADIN_LEGO_R DAGND2 ADIN_LEGO_L DAGND2 DA3.3V TO 2E DGND C2189 1N-K-1005 ADIN_VDCOM C2193 1N-K-1005 A_DIN_L C2188 1N-K-1005 DAGND2 DAGND2 C2187 1N-K-1005 A_DIN_R...
Page 19
SCH11 DIGITAL CNT DIGITAL 6/11 N1007 TO E3 (DIGITAL CNT) D.SUPPLY H_PR H/P_R H_PGND H/P_GND H_PL H/P_L DAGND2 AGND N1001 ZONE2_R ZONE2_R AGND N1001 ZONE2_L C125Z2-19 ZONE2_L AGND R2080 DAC_MS BT_TX_R FROM DAC_MS DAC_MS1. BTTX_R TO C7 R2081 AP_CK AP_CK AP_CK.
Page 20
SCH12 SPK SPK_F-CNT 1/3 SPEAKER B'D CN4000 FL_1 FL_A SPK-A L CH SPK A RLY TO CP4800 FR_A SPK-A R CH FV-A ¡Ø CAPACITOR OPTION C4016-C4019 U1B,FN N1B,N1SG 2200PF 0.018UF 2200PF 0.018UF FL_B SPK-B L CH SPK B RLY FR_1 FR_B SPK-B R CH FV-B...
Page 21
SCH13 FRONT CNT SPK_F-CNT 2/3 CP5202 CP5201 DIGITAL DIGITAL (DIGITAL CNT 6/11 F8) (DIGITAL CNT 6/11 M2) FRONT-CNT B'D TO N1005 TO N1007 GUIDE "L" B'D TO DIGITAL BD LEGO_VDCOM LEGO_R LEGO_L AGND GUIDE "TOP" B'D DA+5V DA+5V CP5200 TO AV B'D AV_S-CNT TO CN5200 (AV 1/3 J2)
Page 22
SCH14 DAB (N only) SPK_F-CNT 3/3 DAB B'D N1B/N1SG only CP5501 C22542-5085-26G ADC3 ADC2 CN5500 JP5503 R5503 ADC1 0(2012) JP5504 R5523 0(2012) ADC0 0(2012) R5524 0(2012) C5503 CN5500 OPEN AUDIO_L C5505 C125Z2-09 OPEN R5525 0(2012) AGND C5506 AUDIO_R OPEN DAB_L_OUT C5504 SCL0 OPEN...
Page 23
SCH15 Input, Volume, Preout, Zone2 _CP5201 CP5206 CN5200 CN5201 CN5202 TO CN4301 TO CN4303 TO CP5200 TO CP4002 TO CP4000 AV_S-CNT 1/3 AV_S-CNT AV_S-CNT SPK_F-CNT SPK_F-CNT SPK_F-CNT (S-CNT 3/3 I10) AV BD (Input / Volume / Preout / Zone2) (S-CNT 3/3 B10) (F-CNT 2/3 K9) (SPK 1/3 B9) (SPK 1/3 B8)
Page 25
SCH17 SIDE CONNECTOR CP4302 CP4303 CP4301 AV_S-CNT 3/3 TO N1001 TO N1003 TO N1002 DIGITAL DIGITAL DIGITAL SIDE CONNECTOR BD (DIGITAL CNT 6/11 F2) (DIGITAL CNT 6/11 F5) (DIGITAL CNT 6/11 M4) C4355 100P-J C4356 100P-J DA+5V C4319 48 PDN 1/100(5*11) 47 VDD18 46 DVSS...
Page 26
SCH18 FRONT FRONT 1/1 FRONT B'D AREA OPTION R4403 R4410 N/F/K R4409 OPEN C4402 R4400 100N-K R4410 A2505-WR07_2.5MM C4410 R4403 OPEN FIL2 C4403 R4401 OPEN 100N-K R4404 OPEN FIL1 OPEN D4400 R4402 F4400 Q4400 1N4007 4R7(1) MF2410F0.500TM KTC1027Y Vkk GND OPEN F500mAL/125V Q4412...
Page 28
OPEN ZJ15B OPEN OPEN OPEN OPEN OPEN OPEN OPEN 100/400 0.1/275V CT710eV5V222M400VacB OPEN T2AL T6.3AL T1.6AL T3.15AL NR1200 ZJ6.2B ZJ39B ZJ39B ZJ39B ZJ15B 2M2 (5) 2M2 (5) 1M (5) 270K 100/200 0.22/275V CT710eV5V222M400VacB OPEN * LINE_FILTER OPTION U1B,FB N1SG, N1B...
PRINTED CIRCUIT BOARDS DIGITAL Lead-free Solder DIGITAL (A SIDE) When soldering, use the Lead-free Solder (Sn-Ag-Cu). NR1200 DIGITAL [MP] 7020-08471-000-0S C1753 C1752 C1786 C1780 N1032 C1751 C1827 C1835 N1006 N1023 6. RESETOUT 5. D5.2V TP1183 Q1029 4. D5.2V C2192 R2068...
Page 31
SIDE CNT, AV SIDE CNT (A SIDE) SIDE CNT (B SIDE) NR1200 SIDE CNT B'D (MP) C4306 C4305 C4304 C4303 C4302 C4301 CP4304 7020-08475-000-0V C4313 RLGND RLGND RL+B C4311 RL+B C4309 TU+5V TU+5V TUGND TUGND AGND AGND AGND AGND A-8V...
Page 32
SPK, FRONT CNT, GUIDE_TOP, GUIDE_L, DAB (N Only) SPK (A SIDE) SPK (B SIDE) BLACK BLACK BLACK BLACK BLACK BLACK BLACK BLACK C4032 C4038 C4033 C4039 C4034 C4040 C4041 C4035 C4042 JACK4003 JACK4002 JACK4001 JACK4000 C4036 C4043 FL_B FR_B FL_A FR_A C4037 C4017...
LEVEL DIAGRAM FRONT ch NR1200 LEVEL DIAGRAM FRONT ch NJU72750 NJU72343 ANALOG H/POUT SPEAKER LINE IN + GAIN + AK5358B + PREOUT + - - - AK4458VN - + + - to ZONE2 +30dB NJU72343 MAX. OUTPUT 4.2Vrms SP OUT Differential Out 4.48Vrms/8Ω...
Page 37
ZONE2 ch (w/Source) NR1200 LEVEL DIAGRAM Distribution ZONE2(w/ Source) NJU72750 NJU72750 PCM9211 LINE IN To LEGO BT_TX PCM5100 AK5358B NJU72343 HEOS ZONE2 PCM5100 GAIN from F-ch +30dB Differential Out GAIN setting of MASTER VOL 00dB PCM5100 ・DIGITAL in -2.0dB + 7dB = +5.0dB...
Page 38
ZONE2 ch (w/o Source) NR1200 LEVEL DIAGRAM ZONE2(w/o Source) NJU72750 NJU72750 LINE IN BT_TX PCM5100 AK5358B NJU72343 HEOS ZONE2 PCM5100 GAIN from F-ch +30dB +20dB +20dB +10dB +10dB -2.0dB LINE IN 200mV PREOUT 150mVrms -10dB -10dB -20dB -20dB -30dB -30dB...
BLOCK DIAGRAM ANALOG AUDIO DIAGRAM NR1200 ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK BUFFER INVERTING U/F version : Buffer AMP N version : Gain AMP BUFFER INVERTING DAB_L H/P-L N version DAB_R H/P-R 7-INPUT/3-OUT TUNER_L TUNER NJU72750 U/F version TUNER_R...
Page 40
DIGITAL AUDIO DIAGRAM NR1200 DIGITAL AUDIO DIAGRAM ADV7623 OUT0 HDMI TRANSCEIVER KEY_MATRIX 10MHz TMDS TMDS OUT0 MN864788 CON MN864787 CON TMDS TMDS ADV7623 MAIN HDMI4 MICOM TMDS TMDS HDMI5 R5F5651EDDFB FUNCTION DATA TMDS TMDS HDMI1 OUT1 OSD DATA TUNER CONT HDMI2.0...
WIRING DIAGRAM NR1200 WIRING BLOCK DIAGRAM Wi-Fi_ANT Wi-Fi/BT_ANT AC CORD Wi-Fi_ANTENNA Wi-Fi_ANTENNA 2P_WIRE_60MM LEGO DIGITAL PCB MODULE MAIN + SPK PCB 40P_FFC_190MM(SHIELD) AC POWER S1 TAP 5P_WIRE_310MM(SHIELD) 2P_WIRE_140MM FRONT CNT PCB 10P_WIRE_50MM(RLY) AV PCB MAIN POWER TRANS SMPS PCB 4P_WIRE_50MM(CURRENT DET)
Page 44
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F5631FDDFB(DIGITAL_MCU : U1013) Pin Name Symbol Pu/Pd STBY STOP Function STBY UPSEL/P35(IN)/NMI DSP_FLAG0 DSP(ADI) interrupt signal input pin...
Page 45
Pin Name Symbol Pu/Pd STBY STOP Function Pin Name Symbol Pu/Pd STBY STOP Function STBY STBY Power supply pin. Protection detect signal input pin (for DC and ASO) (A/D PE4/AN102 DC_DET/ASO SW3VPu converter) Pins for setting the boot mode(select the Boot Mode or PC7/TXD8/IRQ14 PE3/AN101 AMPSIGDET...
Page 46
PCM9211 www.ti.com SBAS495 – JUNE 2010 PIN CONFIGURATIONS PCM9211 (DIGITAL : U1040) PT PACKAGE LQFP-48 DESCRIPTION (TOP VIEW) NAME TOLERANT 26 MS/ADR1 Software control I/F, SPI chip select / I2C slave address setting1(2) ERROR/INT0 VDDRX 27 MODE Control mode setting, (see the Serial Control Mode section, NPCM/INT1 RXIN1 MPIO_A0...
W9864G6KH-6(DIGITAL : U1020) Block diagram CLOCK BUFFER CONTROL SIGNAL GENER ATOR COMMAND DECODER COLUMN DECODER COLUMN DECODER CELL ARRAY CELL ARRAY BANK #0 BANK #1 MODE REGIST ER SENSE AMPLIFIER SENSE AMPLIFIER W9864G6KH ADDRESS BUFFER Pin description 5. PIN DESCRIPTION DATA CONTROL CIRCUIT BUFFER...
AK4458VN 40 +105 C (Exposed pad is connected to ground) 40 +85 C (Exposed pad is open) 48-pin QFN (0.5mm pitch) AKD4458 Evaluation Board for AK4458 AK4458VN (DIGITAL : U4300) No. Pin Name I/O Function PD State CAD0_I2C Chip Address 0 Pin in I2C Bus serial control mode Pin Configurations Chip Select Pin in 3-wire serial control mode Hi-Z...
Page 51
NJU72343 (AV : U5202) Pin Function No. Symbol Function No. Symbol Function AREF Analog reference potential terminal DATA IC control data input Address selection terminal CLOCK IC control clock input InA2 Ach input2 VDDOUT Digital power supply output terminal InB2 Bch input2 AREF Analog reference potential terminal...
Page 53
AV Receiver AV Receiver RC-5/ RC-5 Ex. Format Command(*7) AV Receiver AV Receiver Receiver Made by: Marantz America, LLC. DTS NEO:X ON/OFF 16 64 22 RCRC51606422 Function description is located right end. DTS Neo X On/Off VIRTUAL 16 37 51...
Page 54
Graphic EQ ON 16 28 12 RCRC51602812 Graphic EQ turn On Pandora (*4) 27 92 26 RCRC52709226 Turn On and select Pandora as Zone 2 source Graphic EQ OFF Smart Smart Select1 16 30 21 RCRC51603021 16 28 11 RCRC51602811 Graphic EQ turn Off Zone 2 Smart Select 1 Select...
Page 55
/U1x version (for North America) model only /N1x version (for Europe) model only /U1x (for North America), /N1x version (for Europe) model only The RC code can be sent using RS-232C/IP Serial protocol commands Revision 18-Mar-19 Issued NR1510/1710 16-May-19 Issued SR5014/SR6014 17-Jun-19 Issued NR1200...
Page 56
MECHANICAL DISASSEMBLY Flowchart 1. FRONT ASSY 2. RADIATOR ASSY 3. DIGITAL PCB 4. SPK PCB 5. TRANS 6. SMPS PCB 7. REG PCB 8. AV PCB EXPLODED VIEW PACKAGING VIEW...
Page 57
DISASSEMBLY Flowchart • Remove each part following the flow below. • Reassemble the removed parts in the reverse order. • Read "SAFETY PRECAUTIONS" before reassembling the removed parts. • If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work. Failure to shape the wires correctly may cause problems such as noise. • See "EXPLODED VIEW" TOP COVER FRONT ASSY RADIATOR ASSY DIGITAL PCB DISASSEMBLY DISASSEMBLY DISASSEMBLY 1. FRONT ASSY 2. RADIATOR ASSY 3. DIGITAL PCB and "EXPLODED VIEW" and "EXPLODED VIEW" and "EXPLODED VIEW" FRONT PCB 2CH_AMP PCB DIGITAL PCB Ref. No. of EXPLODED VIEW : P 1 Ref. No. of EXPLODED VIEW : P 8 Ref. No. of EXPLODED VIEW : P 16 HP PCB GUIDE_TOP PCB NETWORK MODULE Ref. No. of EXPLODED VIEW : P 2 Ref. No. of EXPLODED VIEW : P 6 Ref. No. of EXPLODED VIEW : P 5 USB PCB GUIDE_L PCB Ref. No. of EXPLODED VIEW : P 3...
• For the shooting direction of each photos used in this manual, see the photo below. • A, B, C and D in the photo below indicate the shooting directions of photos. Proceeding : TOP COVER → FRONT ASSY • The photographs with no shooting direction indicated were taken from the top of the unit. (1) Remove the screws. • Photos of NR1200 U are used in this manual. The viewpoint of each photograph (Shooting direction : X) [View from the top] ↓Shooting direction: B↓ View from the bottom (2) R emove the screws. Remove the CORD HOLDER and connectors. Remove the FFC. CP4401 CP4403 CORD HOLDER x5 ↑Shooting direction: A↑...
2. RADIATOR ASSY 3. DIGITAL PCB Proceeding : TOP COVER → RADIATOR ASSY Proceeding : TOP COVER → DIGITAL PCB (1) Remove the screws. (1) Remove the screws. View from the bottom ↑Shooting direction: A↑ (2) R emove the FFC. Cut the wire clamp, then remove the connector. Remove the CORD HOLDER. (2) C ut the wire clamp, then remove the connector. Remove the CORD HOLDER. CP4401 Remove the FFC.
Page 60
4. SPK PCB 5. TRANS Proceeding : TOP COVER → DIGITAL PCB → SPK PCB Proceeding : TOP COVER → DIGITAL PCB → TRANS (1) Remove the screws. (1) Remove the CORD HOLDERs and connector wires. from CP4401 CP4001 CP4607 ↑Shooting direction: A↑ (2) Remove the screws. Remove the CORD HOLDER and connectors. Remove the HOLDER. CORD HOLDER CP4800 CP4802 CP4121 CP4001...
EXPLODED VIEW http://dmedia.soundunited.com/documents/details/26046 Parts List : NR1200(Marantz) EXPLODED VIEW S 1 - S 9 - Only N1B/N1SG S 1 3 S 1 3 S 1 - S 7 - S 1 - / F N U 1 B - 2 (...
Page 62
PACKAGING VIEW http://dmedia.soundunited.com/documents/details/26046 Parts List : N R 12 *MANUAL POLYBAG ASSY* POLYBAG CODE: 6337-04006-201-0S POLYBAG CODE: 6330-21071-900-0S ZIPPERBAG(A4size) ZIPPERBAG(A5size) EU toll-free leaflet (Mz) (N only) AWA insertion sheet (F only) Notes on RADIO (ALL) Cautions on Using Batteries (N Only) SPOTIFY insertion sheet (U/N) SAFETY INST.
REPAIR INFORMATION TROUBLE SHOOTING SPECIAL MODE 1. POWER Special mode setting button 2. HDMI/DVI 1. Version Display Mode 3. AUDIO 2. PANEL / REMOTE LOCK Selection Mode 4. Network / Bluetooth / USB 3-1. Selecting the Mode for Service-related 5. SMPS 3-2.
Page 64
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on 1.2. Fuse is blown The unit does not power on Blown fuse Check for short circuits between the Does the power indicator on the front panel flash Check the rectifier diode in the Does the power shut down after several seconds? Check for leaks and short circuits regulator output terminal and GND...
Page 65
2.1. No picture or sound is output (HDMI to HDMI) No picture or sound is output. (8) When using a MARANTZ Blu-ray/DVD player, is the "HDMI" indicator of the fluorescent display lit? Proceed to YES when using a Blu-ray/DVD player produced by other manufactures.
Page 66
(15) Are a picture and sound output when a differ- The TV is faulty. ent TV is used? Check the unit. "HDMI "Rx/Tx" Failure Detection"...
3.2. Power AMP (AMP PCB) 3.3. Analog audio When using the protection pass mode, do not connect speakers to the speaker terminals. No audio output. No audio output. Protection is activated. Is a voltage of ± 8 V supplied to AV PCB [CP5201]? Repair the ±...
4. Network / Bluetooth / USB 4.1. Cannot connect to the network Check the connection environment The circuit of NET5V POWER Insert the LAN cable correctly and then turn on Can the output voltage (5V) to Is NET5V POWER [U1013 : 52pin Is the LAN cable correctly inserted? between [U1013-Q1083 : FET- the power again.
4.2. Cannot establish a Bluetooth connection Check the Bluetooth device being used Are the versions of the HEOS Version displayed in The Network Module software is faulty. Version Check Mode? Is the Bluetooth device compatible with the A2DP Use a device that is A2DP profile compatible. profile? The circuit of Network Module is faulty.
Page 71
4.3. Cannot recognize the connected USB device 4.4. No picture or sound is output Check the USB device being used Checking the unit (If no picture is output) Are digital video signals(LEGOPCK, LEGOVS, The circuit around Network Module, [U1024 : Is a USB hub being used? Do not use a USB hub.
Page 73
5. SMPS Operation waveform for each part DC 5V is not output. After primary side rectification Primary drain (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) Replace the [U4140 : TOP268VG Is [U4140 : TOP268VG] dam- and D4142 / D4143 / D4144 / After secondary rectifications aged? D4145].
Page 74
HDMI "Rx/Tx" Failure Detection 1. Prior checking Check item(1.). : Checking the HDMI connector Checking the condition of the HDMI pin (rear/front). There are deformed pins. Replace the HDMI connector. Check for deformed pins. None of the pins are deformed. Check by following the flow chart for "3.
Page 75
flexible card cable. Parity: none Transmitted text S706-709 : No Preference S702 : 3.3V Flow control: none Select Append CR-LF Figure 1 Device Connection Method (NR1200) Forward: (none) Check the Local Echo check box. Figure 3. Serial Port Setup Screen...
After exiting "Setup Assistant" execute the above. 1. Input a command in the 2.Click on the transmission button. transmission command input. Press Figure 6-1. AVR settings (NR1200) Figure 8. Method for Sending Termite Commands All the for Volume 7 segment indicator Lights...
3. Starting detecting the point of failure Check item(3.1.). Display when an Error is not detected. Check the power supply status and communication status with the CPU of each device. Start in HDMI Diagnostics mode and follow the procedures below. 1 Auto Test Cancel the mode, and proceed to check item...
Page 78
Check item(3.2.). : Check operation of the HDMI input terminal. Check item(3.3). : Check operation of the HDMI output termi- nal. Go to check item (3-9.1.). When the HDMI input terminal of this device is connected to the player correctly, is sound heard from (OSD [ADV7623] failure detection the speaker? procedure)
Page 79
3-1. Error Code H1-01 failure detection procedure Checking device. (HDMI Rx/Tx) Check the power supply voltage. (HDMI Rx/Tx) Checking the reset waveform. (HDMI Rx/Tx) Check item(3-1.1.). Check the power supply voltage. : Check item(3-1.3.). Checking the reset waveform : Check the waveform. Does the power supply voltage of the HDMI Rx/Tx [U1027] indicate the correct voltage (1.1V, 3.3V)? When the power is turned on, is the TP waveform correct (as The test points are as follows.
Page 80
Check the I2C communication line. (HDMI Rx/TX) Check item(3-1.4.). Check the I2C communication line : Check the CPU. Is the "I2C" waveform of the TP HDMI Rx/Tx [U1027] correct (like the one shown in the diagram) when the power is turned P_DA 116pin P_CK 114pin U1027...
Page 81
3-2. Error Code H1-02 failure detection procedure Checking device. (HDMI SW) Checking the reset waveform. (HDMI SW) Check item(3-2.1.). Checking the reset waveform : Check the waveform. When the power is turned on, is the TP waveform correct (as shown in the figure)? Examples of confirmation waveform 115 pin Voltage scale:1.0V/div...
Page 82
3-3. Error Code H1-07 failure detection procedure Checking device. (OSD) Check the power supply voltage. Checking the reset waveform. Check item(3-3.3.). Checking the reset : Check item(3-3.1.). Check the power supply volt- Check item(3-3.2.). Check the power supply volt- age. : age.
Page 83
Check the I2C communication line. Check item(3-3.4.). Check the I2C communication line : Check the CPU. Is the "I2C" waveform of the HDMI OSD [U1030] correct (like the one shown in the diagram) when the power is turned on? HSCL HSDA U1030 *The diagram shows an example.
Page 84
3-4. Error Code H1-15 failure detection procedure Checking device. [U1029 : MX25L3206EMI(U, K, F)/MX25L6406EMI(N)] Check item(3-4.1.). Write to the OSD ROM. Recheck from check item (3.1.). Does Error Code H1-15 continue? Check item(3-4.2.). Replace [U1029] with a new device. Recheck from check item (3.1.).
Page 85
3-5. Error Code H1-08 failure detection procedure Checking device. [U1021 : ADSP21487] Check the power supply voltage. Checking the reset waveform. Check item(3-5.1.). Check the power supply volt- Check item(3-5.2.). Check the power supply volt- Check item(3-5.3.). Checking the reset : age.
Page 86
Check the SPI communication line. Check item(3-5.4.). Check the SPI communication line : Check the CPU. Is the "SPI" waveform of the TP near the DSP [U1021] correct (like the one shown in the diagram) when the power is turned on? D_CK 3pin D_MOSI 4pin D_CS 6pin...
Page 87
3-6. Error Code H1-12 failure detection procedure Checking device. [U1040 : PCM9211] Check the power supply voltage. Checking the reset waveform. Check item(3-6.1.). Check the power supply volt- Check item(3-6.2.). Check the power supply volt- Check item(3-6.3.). Checking the reset : age.
Page 88
Check the communication line. Check item(3-6.4.). Check the communication line : Check the CPU. Is the waveform of the TP near the DIR [U1040] correct (like the one shown in the diagram) when the power is turned on? DR_CK 25pin DR_DIN 24pin DR_CE 26pin DR_DOUT 23pin...
Page 89
3-7. HDMI Rx [MN864788] failure detection procedure Checking operation between the HDMI Rx/Tx device and the player Check item(3-7.2.). Checking the DDC status register : Example Send the following command from Termite.exe. b In order to check, connect the player to the HDMI terminal and configure the player as AVR source. Case of HDMI IN4 Check the sound output while turning on the player.
Page 90
When the results of check item (3-7.1.) are "00" When the results of check item (3-7.2.) are "00 or 04" (Detection of 5V is not OK) (Detection of DDC is not OK.) Check the +5V voltage. (HDMI Rx/TX) Check the DDC line. (HDMI Rx/Tx) Check item(3-7.3.).
Page 91
When the results of check item (3-7.2.) are "22" (Detection of DDC is OK.) Checking the TMDS status register 3.3V TMDS Signal TMDS Check item(3-7.5.). Checking register of the TMDS CLK detection status Example register : Example of waveform in check ① Example of waveform in check ② Send the following command from Termite.exe.
Page 92
3-8. HDMI SW [MN864787] failure detection procedure Checking operation between the HDMI (HDMI SW) device and the player HDMI IN1-3 Check item(3-8.2.). Checking the DDC status register : Example Send the following command from Termite.exe. Case of HDMI IN1 b In order to check, connect the player to the HDMI terminal and configure the player as AVR source. Send the command "i 002B 0084 0001".
Page 93
When the results of check item (3-8.1.) are "00" When the results of check item (3-8.2.) are "00 or 04" (Detection of 5V is not OK) (Detection of DDC is not OK.) Check the +5V voltage. (HDMI SW) Check the DDC line. (HDMI SW) Check item(3-8.3.).
Page 94
When the results of check item (3-8.2.) are "22" (Detection of DDC is OK.) Checking the TMDS status register (HDMI SW) 3.3V TMDS Signal TMDS Check item(3-8.5.). Checking register of the TMDS CLK detection status Example register : Example of waveform in check ① Example of waveform in check ② Send the following command from Termite.exe.
Page 95
3-9. OSD [ADV7623] failure detection procedure Checking the TMDS status register (OSD -> HDMI Rx/Tx) 3.3V TMDS Signal Check item(3-9.1.). Check the TMDS CLK detection status of the Check item(3-9.2.). Checking the TMDS input waveform. : Example register. Check the TMDS waveform at the following test point. Send the following command from Termite.exe.
Page 96
Check the connection between the HDMI OUT terminal and the TV. Connect the HDMI OUT terminal and the TV, and then turn on the TV and check the following items. Checking the HPD/RXSENSE status register. (HDMI TX -> Monitor) Check item(3-9.3.). Check the HPD and RXSENSE register value of Example the HDMI TX device.
Page 97
When the results of check item (3-9.3.) are "03" (Detection of HPD is OK / Detection of RXSENSE is OK ) Example Checking the EDID register. (Monitor) Check item(3-9.4.). Check the Monitor EDID : ① Unplug the AC cord. Plug the AC cord into a power outlet. ②...
Page 98
When the results of check item (3-9.3.) are "01" When the results of check item (3-9.3.) are "02" (Detection of HPD is OK / Detection of RXSENSE is not OK ) (Detection of HPD is not OK / Detection of RXSENSE is OK ) Check the RXSENSE.
Page 99
When the results of check item (3-9.3.) are "00" (Detection of HPD is not OK / Detection of RXSENSE is not OK ) Check the RXSENSE/HPD. (Monitor) Check item(3-9.9.). Checking the HPD and RXSENSE. : Does the test point of RXSENSE close to the HDMI output terminal [N1018] indicate the (3.3V)? Does the voltage of HPD test point close to the HDMI output terminal [N1018] indicate "Hi"...
Page 100
3-10. Fault detection procedure between HDMI Rx/Tx [MN864788] & OSD [ADV7623]. HDMI IN1 HDMI OUT ※ In order to check, connect the player to the HDMI terminal and configure the player and TV as AVR source. Check the sound output while turning on the player and TV. Checking the TMDS status register (Rx/Tx ->...
SPECIAL MODE Special mode setting button b No. 1 - 4, 6 - 8 : While holding down buttons "A", "B" and "C" simultaneously, press the power button to turn on the power. b No. 5, 9, 10 : While the power is on, hold down buttons "A", "B", and "C" for at least 3 seconds . Mode Button A Button B Button C Descriptions...
Page 104
1. Version Display Mode 1.1. Actions Q1 HEOS Version : Q6 Restore Version : Version information is displayed when the device is started in this mode. HEOS Version RSTR "Press "STATUS" button. "Press "STATUS" button. 1.2. Starting up While holding down buttons "DIMMER" and "STATUS" simultaneously, press the power button to turn *.***.*** ************ on the power.
1.4. Error display See the table below for descriptions of the displayed errors and countermeasures for these. If multiple errors occur, only one item is displayed. The priority order is w, e, r, q. Condition States Display TROUBLE SHOOTING The model name, brand name and region information written in the firmware are compared •...
Page 106
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 16-digit number as shown in the screenshot below. General/Firmware Version XXXX-XXXX-XXXX-XXXX...
Page 107
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Switch the PANEL LOCK and REMOTE LOCK modes between on and off. RC LOCK • PANEL LOCK Mode (with Volume) The device cannot be operated by the remote control. Disables reception from all keys and encoders on the front panel except the power button (including the volume).
3-1. Selecting the Mode for Service-related 3-1.1. Actions Select diagnostic mode (service path check mode), protection history display mode, or Operation Info 4.OP INFO mode or TUNER STEP mode. Operation Info for the unit can be checked. 3-1.2. Starting up While holding down buttons "ZONE2 SOURCE"...
3-2. Protection History Display Mode 3-2.1. Actions (3) DC (if the last protection is DC) This mode enables the unit to record and display the event when the THERMAL, ASO or DC protection is PRT:DC activated. Cause : DC output of the power amplifier is abnormal. If protections have been activated multiple times, the latest protection operation is recorded.
Page 110
3-2.4. Clearing the Protection History There are two ways to clear the protection history. (1) Activate Protection History Display Mode. Press the "STATUS" button to display the protection history. PRT:DC Press and hold the "DIMMER" button for 3 seconds. PRT:CLEAR The above is displayed and protection history is cleared.
Page 111
3-3. Operation Info Mode 3-4. TUNER STEP mode (U only) 3-3.1. Actions 3-4.1. Actions This mode enables the unit to display the accumulated operating time, power On count and each This is a special mode that enables the reception frequency STEP of the FM/AM TUNER to be changed. protection count.
4. Protection Pass Mode 5. Network Initialization Mode 4.1. Actions 5.1. Actions • This mode allows the power to be turned on without activating protections. The following items are initialized. • This mode functions in the same way as normal power-on, except that protections are not activated. Network setup •...
Page 113
6. Clearing of Operation Info 7. Log Capture feature 6.1. Actions 7.1. Actions • Displays the accumulated operating time of the unit, the number of times the power was switched • Acquires the Network Module log. on, and the number of occurrences of each protection. •...
Page 114
DIAGNOSTIC MODE Service Path Check Mode 1.1. Actions This function is convenient for confirming problem paths in the product and checking the paths after repairing. The video system and audio system operation paths can be checked. The backup data is not rewritten. 1.2.
Page 115
Paths to be confirmed Display Settings What to confirm Input Source : CBL/SAT • Analog input ⇒ Speaker output (Front L/R, Center, Surround L/R) Input Mode : Analog (fixed) • Analog input ⇒ SW(20Hz) fig.A05a Analog AD Sound mode : STEREO ( b The input source can be switched to any source except CBL/SAT.) A06:AD (MAIN ZONE)
DIAGNOSTIC PATH DIAGRAM fig.A01 NR1200 ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK BUFFER INVERTING U/F version : Buffer AMP N version : Gain AMP BUFFER INVERTING DAB_L H/P-L N version DAB_R H/P-R 7-INPUT/3-OUT TUNER_L TUNER NJU72750 U/F version TUNER_R 8-CH VOLUME...
Page 117
NR1200 DIGITAL AUDIO DIAGRAM ADV7623 OUT0 HDMI TRANSCEIVER KEY_MATRIX 10MHz TMDS TMDS OUT0 MN864788 CON MN864787 CON TMDS TMDS ADV7623 MAIN HDMI4 MICOM TMDS TMDS HDMI5 R5F5651EDDFB FUNCTION DATA TMDS TMDS HDMI1 OUT1 OSD DATA TUNER CONT HDMI2.0 TMDS...
Page 118
NR1200 ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK BUFFER INVERTING U/F version : Buffer AMP N version : Gain AMP BUFFER INVERTING DAB_L H/P-L N version DAB_R H/P-R 7-INPUT/3-OUT TUNER_L TUNER NJU72750 U/F version TUNER_R 8-CH VOLUME 7-INPUT/3-OUTPUT NJU72343...
Page 119
NR1200 DIGITAL AUDIO DIAGRAM ADV7623 OUT0 HDMI TRANSCEIVER KEY_MATRIX 10MHz TMDS TMDS OUT0 MN864788 CON MN864787 CON TMDS TMDS ADV7623 MAIN HDMI4 MICOM TMDS TMDS HDMI5 R5F5651EDDFB FUNCTION DATA TMDS TMDS HDMI1 OUT1 OSD DATA TUNER CONT HDMI2.0 TMDS...
Page 120
NR1200 ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK BUFFER INVERTING U/F version : Buffer AMP N version : Gain AMP BUFFER INVERTING DAB_L H/P-L N version DAB_R H/P-R 7-INPUT/3-OUT TUNER_L TUNER NJU72750 U/F version TUNER_R 8-CH VOLUME 7-INPUT/3-OUTPUT NJU72343...
Page 121
NR1200 DIGITAL AUDIO DIAGRAM ADV7623 OUT0 HDMI TRANSCEIVER KEY_MATRIX 10MHz TMDS TMDS OUT0 MN864788 CON MN864787 CON TMDS TMDS ADV7623 MAIN HDMI4 MICOM TMDS TMDS HDMI5 R5F5651EDDFB FUNCTION DATA TMDS TMDS HDMI1 OUT1 OSD DATA TUNER CONT HDMI2.0 TMDS...
Page 122
NR1200 ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK BUFFER INVERTING U/F version : Buffer AMP N version : Gain AMP BUFFER INVERTING DAB_L H/P-L N version DAB_R H/P-R 7-INPUT/3-OUT TUNER_L TUNER NJU72750 U/F version TUNER_R 8-CH VOLUME 7-INPUT/3-OUTPUT NJU72343...
Page 123
NR1200 DIGITAL AUDIO DIAGRAM ADV7623 OUT0 HDMI TRANSCEIVER KEY_MATRIX 10MHz TMDS TMDS OUT0 MN864788 CON MN864787 CON TMDS TMDS ADV7623 MAIN HDMI4 MICOM TMDS TMDS HDMI5 R5F5651EDDFB FUNCTION DATA TMDS TMDS HDMI1 OUT1 OSD DATA TUNER CONT HDMI2.0 TMDS...
Page 124
NR1200 ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK BUFFER INVERTING U/F version : Buffer AMP N version : Gain AMP BUFFER INVERTING DAB_L H/P-L N version DAB_R H/P-R 7-INPUT/3-OUT TUNER_L TUNER NJU72750 U/F version TUNER_R 8-CH VOLUME 7-INPUT/3-OUTPUT NJU72343...
Page 125
NR1200 ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK BUFFER INVERTING U/F version : Buffer AMP N version : Gain AMP BUFFER INVERTING DAB_L H/P-L N version DAB_R H/P-R 7-INPUT/3-OUT TUNER_L TUNER NJU72750 U/F version TUNER_R 8-CH VOLUME 7-INPUT/3-OUTPUT NJU72343...
Page 126
NR1200 ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK BUFFER INVERTING U/F version : Buffer AMP N version : Gain AMP BUFFER INVERTING DAB_L H/P-L N version DAB_R H/P-R 7-INPUT/3-OUT TUNER_L TUNER NJU72750 U/F version TUNER_R 8-CH VOLUME 7-INPUT/3-OUTPUT NJU72343...
Page 127
NR1200 DIGITAL AUDIO DIAGRAM ADV7623 OUT0 HDMI TRANSCEIVER KEY_MATRIX 10MHz TMDS TMDS OUT0 MN864788 CON MN864787 CON TMDS TMDS ADV7623 MAIN HDMI4 MICOM TMDS TMDS HDMI5 R5F5651EDDFB FUNCTION DATA TMDS TMDS HDMI1 OUT1 OSD DATA TUNER CONT HDMI2.0 TMDS...
Page 128
NR1200 ANALOG AUDIO DIAGRAM TO DIGITAL AUDIO BLOCK BUFFER INVERTING U/F version : Buffer AMP N version : Gain AMP BUFFER INVERTING DAB_L H/P-L N version DAB_R H/P-R 7-INPUT/3-OUT TUNER_L TUNER NJU72750 U/F version TUNER_R 8-CH VOLUME 7-INPUT/3-OUTPUT NJU72343...
JIG FOR SERVICING (3) Remove the DIGITAL PCB from the chassis and turn it over. Use the following jigs (extension cable kit) when repairing the PCBs. Place an insulation sheet larger than the PCB underneath the DIGITAL PCB. Order with your dealer for the jigs your dealer if necessary. b Connect the earth of the PCB to the chassis using an earth wire, etc.
ADJUSTMENT Adjusting Idling Current NOTE: Adjusting the idling current when "ECO Mode" is set may damage the Power AMP. 1. Preparation (1) Prepare a DC voltmeter. AMP UNIT (2) Place the unit under normal usage conditions, away from highly ventilated areas such as next to an air conditioning machine or electric fan.
Page 135
UPDATING PROCEDURE AFTER REPLACING THE PCB. PROCEDURE AFTER REPLACING THE U-COM, ETC. FIRMWARE UPDATE PROCEDURE 1. Items necessary for update 2. Update preparation with a USB flash drive 3. Update method when the DIGITAL PCB or network module is replaced (Using a USB flash drive) 4.
Page 136
U1029 SOFTWARE : GUI ROM MX25L6406EM2I for N (2) Be sure to replace the software with the latest version. DIGITAL U1041 5M570ZF256C5N SOFTWARE : AUDIO PLD NR1200 DIGITAL [MP] DIGITAL U1048 EN25QH32B-104HIP2C SOFTWARE : PIMG ROM 7020-08471-000-0S C1753 C1752 C1786...
Update download file when the firmware is updated (Two files, "HW component" and "LEGO component") Download from SDI Model Name Model Area For HW component For LEGO component NR1200 U North America (U) Product ID : 100100730100 DPMS_NR1200U_LEGO_xxxx.zip NR1200 N Europe (N) Product ID : 100100730200 DPMS_NR1200N_LEGO_xxxx.zip...
Page 138
2. Update preparation with a USB flash drive You can update the firmware by downloading the latest version with USB flash drive. 2.1. Connecting to the USB flash drive (1) Preparation • Windows PC • USB flash drive format : Prepare a USB flash drive formatted in FAT16 or FAT32. b We recommend a USB flash drive that has an LED installed.
Page 139
3. Update method when the DIGITAL PCB or network module is replaced (Using a USB flash drive) 3.1. File structure on USB flash drive (5) USB Update starts automatically. The Standby LED lights red. DIGITAL PCB or network module is replaced onto the USB flash drive in the following structure. Display during USB update After unzipping the files, store them in the root of the same USB flash drive.
Page 140
4. Update Method for Service Region Settings Copy the Service Region Settings from the USB flash drive to this unit. (5) Copy the files created on the USB flash drive. 4.1. Creating a Service Region Settings file (1) Click [Start button] - [Accessories] - [notepad] on the PC to launch the notepad. copy to USB flash drive (2) Enter "TEXT".
Page 141
5. Normal Firmware Update Method from USB Flash Drive 5.1. File structure on USB flash drive (1) Press the power button to turn on the power. (2) Wait for this unit to start up. Copy the normal update files onto the USB flash drive in the following structure. (3) Set the input source to HEOS Music.
6. Normal Firmware Update Method from OTA 6.2. Check and update the firmware Download the latest firmware from our website and update the firmware. Check if there is a firmware update available. It is also possible to check approximately how long the ---Cautions on Firmware Update--- update will take.
Page 143
Update ErrorYYXX : DeviceID, : ErrorCode) Update ErrorYYXX DSP2 ↓↑ The display is alternately displayed. b Except : NR1200/NR1510/NR1710/SR5014 DSP3 Please check you b Except : NR1200/NR1510/NR1710/SR5014 Content of the display is scrolled. DSP4 b Except : NR1200/NR1510/NR1710/SR5014 Audio PLD...