Marantz NR1200 Service Manual page 44

SEMICONDUCTORS
Only major semiconductors are shown, general semiconductors etc. are omitted to list.
The semiconductor which described a detailed drawing in a schematic diagram are omitted to list.
1. IC's
R5F5631FDDFB(DIGITAL_MCU : U1013)
PE2 109
PE1 110
PE0 111
P64 112
P63 113
P62 114
P61 115
VSS 116
P60 117
VCC 118
PD7 119
PD6 120
PD5 121
PD4 122
PD3 123
PD2 124
PD1 125
PD0 126
P93 127
P92 128
P91 129
VSS 130
P90 131
VCC
132
P47 133
P46 134
P45 135
P44 136
P43 137
P42
138
P41 139
VREFL0
140
P40 141
VREFH0
142
AVCC0
143
P07 144
Note: This figure indicates the power supply pins and I/O port pins. For the pin configuration, see Table 1.8, List of
Pins and Pin Functions (144-Pin LQFP).
Terminal Functions
Pin Pin Name Symbol I/O Pu/Pd STBY STOP
1 AVSS0 AVSS -
2 P05/IRQ13 POWER_KEY I
M3VPu
3 AVCC1 AVCC -
4 P03/IRQ11 RED_LED O
5 AVSS1 AVSS -
6 P02/IRQ10/AN120 BAL_A I
SW3VPu
P01/RXD6/IRQ9/
7 RXD_MI232O I
Pd
AN119
P00/TXD6/IRQ8/
8 TXD_MO232I O
AN118
9 PF5/IRQ4 O
GREEN_LED
10 EMLE EMLE I
Pd
11 PJ5 VSEL_A I
SW3VPu
12 VSS VSS -
13 PJ3 VSEL_B I
SW3VPu
14 VCL VCL I
15 VBATT VBATT -
16 MD/FINED MD I
M3VPu
17 XCIN XCIN I
Pd
18 XCOUT XCOUT I
19 RES# RESET I
M3VPu
20 XTAL/P37 XTAL I
21 VSS VSS -
22 EXTAL/P36 EXTAL -
23 VCC VCC -
72 P74
71 P75
70 PC2
69 P76
68 P77
67 PC3
PC4
66
65 P80
64 P81
63 P82
PC5
62
61 PC6
PC7
60
RX63N Group 59 VCC
P83
58
RX631 Group 57 VSS
P50
56
PLQP0144KA-A
55 P51
54 P52
(144-pin LQFP)
53 P53
52 P54
(Top view)
P55
51
50 P56
VSS_USB
49
48 USB0_DP
USB0_DM
47
46 VCC_USB
P12
45
44 P13
P14
43
42 P15
P86
41
40 P16
P87
39
P17
38
37 P20
CEC
Function
STBY
- - - Ground pin
Detect Power switch (Release from Wait Mode,Set to
I I I
interrupt)
- - - Power supply pin
L/H L H POWER/STANDBY LED control pin
- - - Ground pin
I I I Balance (Rotary encoder) signal input pin
External data input port (for AMX/FW update via 232C)
I I I
:Connector is FFC
External data output port (for AMX/FW update via 232C)
L L L
:Connector is FFC
L L L POWER LED control pin
E20 Emulator control pin (On chip Emulator is used,this
- - -
pin should be High. Not used,it should be Low)
I I I Master volume (Rotary encoder) signal input pin
- - - Ground pin
I I I Master volume (Rotary encoder) signal input pin
- - - Smoothing capacitor connection pin
- - - Power supply pin
Pins for setting the operating mode(select the Boot
I I I
Mode or User Boot Mode,Single Chip Mode)
- - - NC(Pull down)
- - - NC(open)
- - - Reset signal input pin
- - - Pins for a crystal resonator (Xin=12MHz × 10)
- - - Ground pin
- - - Pins for a crystal resonator (Xin=12MHz × 10)
- - - Power supply pin.
Pin Pin Name Symbol I/O Pu/Pd STBY STOP
24 UPSEL/P35(IN)/NMI DSP_FLAG0 I
TRST#/P34/SCK6/ TRST#/
25 I/I
SCK0/IRQ4 NC(NORMRAL)
P33/TIOCD0/RXD6/
26 RC_IN I
M3VPu
RXD0/IRQ3-DS
P32/TXD6/TXD0/
27 BDOWN I
M3VPu
IRQ2-DS
TMS/
28 TMS/P31/IRQ1-DS I/I
M3VPu
NC(NORMRAL)
TDI/P30/RXD1/ TDI/RXD_MIT-
29 I/O/I
M3VPu
IRQ0-DS SUBISHI
TCK/FINEC/P27/ TCK/
30 I/I/I
M3VPu
SCK1/ NC(NORMRAL)
TDO/TXD_
31 TDO/P26/TXD1 O/O/I
M3VPu
MITSUBISHI
32 P25/RXD3 ADV7623_RST O
33 P24/SCK3 MVOL_MUTE O
34 P23/TXD3 E_RTS_MOEI O
(BCM58305
Internal Pd)
Pd (onboad
35 P22/SCK0 E_CTS_MIEO I
+BCM58305
Internal Pd)
Pd (onboad
36 P21/RXD0/IRQ9 E_RXD_MIEO I
+BCM58305
Internal Pd)
37 P20/TXD0/IRQ8 E_TXD_MOEI O
(BCM58305
Internal Pd)
P17/SCK1/TXD3/ NET_FACT_
38
O(ODR)
(BCM58305
IRQ7 RST
Internal Pu)
7623_ROM_
39 P87 O
HOLD
TU_SCLK(NA/
P16/TXD1/RXD3/
40 JP))/DAB_ O
SW3VPu
IRQ6
TX(EU)
41 P86 PRE_Z2_MUTE O
TU_SDIO(NA/
42 P15/RXD1/IRQ5 JP)/DAB_ I_O
SW3VPu
Rx(EU)
43 P14/IRQ4 VEXP_OE O
44 P13/TXD2/IRQ3 VEXP_CLK O
45 P12/RXD2/IRQ2 VEXP_DATA O
46 VCC_USB VCC_USB -
47 USB0_DM USB0_DM -
48 USB0_DP USB0_DP -
49 VSS_USB VSS_USB -
TU_LA(NA/
50 P56 O
JP)/NC(EU)
51 P55/IRQ10 VEXP_STB O
NET5V_POW-
52 P54 O
ER
53 BCLK/P53 THERMAL_E I
SW3VPu
ADV7623_
54 P52/RXD2 I
SPI_MI
ADV7623_
55 P51/SCK2 O
SPI_CLK
ADV7623_
56 P50/TXD2 O
SPI_MO
57 VSS VSS -
58 P83 TRE_A I
SW3VPu
44
CEC
Function
STBY
L L L DSP(ADI) interrupt signal input pin
Pd
E20 Emulator control pin/When normal operating mode,
I/I I/I I/I
Pd
set to input.
I I I Remote input
I I I Detect power down
E20 Emulator control pin/When normal operating mode,
-/I -/I I
set to input.
E20 Emulator control pin/Mitsubishi writter control pin/
-/-/I -/-/I I
When normal operating mode,set to input.
E20 Emulator control pin//When normal operating mode,
-/-/I -/-/I I
set to input.
E20 Emulator control pin/Mitsubishi writter control pin/
-/-/I -/-/I I
When normal operating mode,set to input.
L L L NC
L L L Volume control pin (NJU72343)
Pd
L L L Ethernet(Network Module) control pin
I I I Ethernet(Network Module) control pin
I L I Ethernet(Network Module) control pin
Pd
L L L Ethernet(Network Module) control pin
Pu
Z Z Z Ethernet(Network Module) control pin
L L L Flash ROM for GUI control pin
Pu
L L L TUNER control
L L L Mute for zone preout control pin
L L L TUNER control
L L L Expander (MC14094) control pin
L L L Expander (MC14094) control pin
L L L Expander (MC14094) control pin
- - - Power supply pin
- - - NC(open)
- - - NC(open)
- - - Ground pin
L L L TUNER control pin
L L L Expander (MC14094) control pin
L L L Ethernet power supply (Net5V) control pin/
I L I Protection detect signal input pin (for Heat sink)
L L L HDMI transceiver w/ GUI(ADV7623) control pin (for GUI)
L L L HDMI transceiver w/ GUI(ADV7623) control pin (for GUI)
L L L HDMI transceiver w/ GUI(ADV7623) control pin (for GUI)
- - - Ground pin
I I I Tone TREBLE (Rotary encoder) signal input pin