Page 1
Frequency Treble Master 1.0K Power Inputs Deep Passive Standby 3.0K Bright Active Resonance YBA100 & YBA300 A L L T U B E B A S S A M P L I F I E R S YBA100 + YBA300...
Important Safety Instructions - English / Français I MP OR TA N T S A FE T Y I N ST R U C TI O N S This lightning flash with arrowhead symbol, within an The exclamation point within an equilatereal triangle is intended to alert the user to the presence equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous of important operating and maintenance (servicing) instructions in the literature accompanying voltage”...
1. D’Alimentation et de Standby ........6 Table of Contents ..............ii 2. D’Entrées 0 dB / Passives et -6 dB / Actives ....6 Traynor YBA100 & YBA300 ..........1 3. Commutateur Deep ............ 6 Features ................1 4. Commutateur Bright ........... 6 1.
• Three 12AX7 pre-amp tubes, a 12AU7 Driver (YBA300 only), and 6L6/EL34 power output tubes (12 on the YBA300 and 4 on the YBA100). That’s 300 watts on the YBA300 (100 watts on the YBA100) of all tube power and tone.
Note: Before powering up and disengaging the Standby switch make sure speaker cabinets are connected to the output jacks. When the amplifier is warmed up, disengage the Standby switch and get ready to experience the classic tone of a Traynor Standby Bassmaster all-tube amplifier.
Connections to these jacks are in parallel. Using the Speaker Load switch, the output of the YBA300 can be op- timized to provide the rated full power (300 watts) for selected loads (4-ohms or 2-ohms). The YBA100 is switch- able between 8-ohms or 4-ohms).
It is only necessary that the individual pairs be matched to each other. Bias Bias The YBA300 does not need 12 matched tubes, just 6 matched pairs. The YBA100 does not need 4 matched tubes, just 2 matched pairs. B i a s B i a s B i a s...
• Trois lampes de préampli 12AX7, un Driver 12AU7 (YBA300 seulement), et des lampes de sortie de puissance 6L6/EL34 (12 sur le YBA300 et 4 sur le YBA100). C’est 300 watts sur le YBA300 (100 watts sur le YBA100) de puissance et de tonalité...
Lorsque l’amplificateur est réchauffé, désengagez l’interrupteur Standby et préparez-vous à découvrir le son classique d’un amplifi- cateur à lampes Traynor Bassmaster. Remarque : Il est recommandé de laisser l’amplificateur sous tension pendant les pauses, l’interrupteur Standby coupe toutes les sorties de l’amplificateur de puissance.
«Speakon». Les connexions à ces prises sont en parallèle. À l’aide du commutateur de charge de haut-par- leur, la sortie du YBA300 peut être optimisée pour fournir la pleine puissance nominale (300 watts) pour les charges sélectionnées (4 ohms ou 2 ohms). Le YBA100 est commutable entre 8 ohms ou 4 ohms). Impedance...
Le YBA300 n’a pas besoin de 12 lampes assortis, seulement 6 paires assorties. Le YBA100 n’a pas besoin de 4 lampes assortis, seulement 2 paires assorties. B i a s B i a s...
Yorkville Sound or your dealer. If this product should fail for any reason within two years of the original purchase date, simply return it to your Traynor dealer with original proof of purchase and it will be repaired free of charge.
Need help?
Do you have a question about the YBA100 and is the answer not in the manual?
Questions and answers