Table of Contents
Advertisement
Available languages
Available languages
ENG ORIGINAL INSTRUCTIONS
of the cut to keep the shoe pressed firmly against
the work piece at all times. Do not force the cut or
stall the saw. Don't bend or twist the blade, let the
tool and the blade do the work. In general, coarser
blades are for wood, plastics, and composites,
and finer blades are for cutting metal. Chattering
or vibration may indicate you need a finer blade or
higher speed. If the blade overheats or clogs, it may
indicate you need a coarser blade. Replace blades
when they become dull. Dull blades will produce por
results and may overheat the saw.
PLUNGE CUTTING.
Clearly mark the line of cut, from a convenient
starting point within the cut out área. Place the tip of
the blade over that point with saw parallel to the line
of cut, slowing lower the saw until the bottom edge
of the shoe rests on the work piece and the blade
not touching the work piece. Start the saw and allow
it to attain full speed. With the saw resting on the
shoe, slowly tilt the saw forward to lower the blade
onto the cut line. Continue this motion until the saw
blade is perpendicular to the work piece.
METAL CUTTING.
Blades specifically designated for cutting metals
must be used for this purpose. You may use light
oil as a coolant when cutting metal, this will prevent
overheating of the blade, help the blade cut faster,
and promote longer blade life.
MAINTENANCE.
The cordless reciprocating saw has been designed
for a long working life with minimum maintenance.
Optimum use depends on correct care of the cord-
less reciprocating saw and regular cleaning. To pre-
vent accidents, always unplug the cordless recipro-
cating saw from the power source before cleaning or
performing any maintenance. The cordless recipro-
cating saw may be cleaned effectively using com-
pressed air after each use. If compressed air is not
available, use a brush to remove dust from the cord-
less reciprocating saw. Motor ventilation vents and
switch levers must be dept clean and free of foreign
matter. Do not attempt to clean by inserting pointed
objects through openings. Cetain cleaning agents
and solvents damage plastic parts, among them are
gasoline, carbon tetrachloride, chlorinated cleaning
solvents, ammonia and household cleaners contai-
ning ammonia. Do not use any of these to clean the
cordless reciprocating saw.
ENVIRONMENT PROTECTION.
The materials and components that have been
used to manufacture this product can be re-used
and recycled. Werku
Management System that is in charge of the co-
rrect elimination of the residues of this product. Do
not eliminate this product with domestic residues.
Werku
offers to its clients a free collection service
®
of these residues through any of its sale points, or
in the collection points established by the Integra-
ted Management System or in the recycling point of
your locality.
WARRANTY AND TECHNICAL SERVICE.
Werku
offers a warranty that covers the repair
®
of all defects found due to faults in the materials
or manufacture. For this cover to be effective it is
necessary for these defects to appear within the
validity period. The consumer is entitled to free
repair of all defects (shipping costs, labour costs
and materials included), either via the repair or by
replacement (if necessary, with a later model). In
any case, Werku
these represent a disproportionate cost compared
to the cost of repair. This warranty does not affect
consumer's rights established by European or na-
tional laws. The validity period of this warranty is 3
years. The validity period starts on the date of pur-
chase by the first consumer. This date is shown
on the invoice or receipt of purchase. Any claims
arising from this warranty must be presented to
the Werku
®
sistance Service. To do so you must present this
warranty correctly completed and stamped by the
distributor, together with the sales invoice or re-
ceipt. To require any information in relation to this
warranty, the buyer and/or distributor may contact
the Technical Assistance Service by telephone on
+34 981 648 119, or by e-mail at info@werku.com.
This warranty does not cover defects caused by
parts that have worn out from use other types of
natural wear, defects caused by failure to observe
the instructions for use and operation, or for appli-
cations other than those for which this product is in-
tended, abnormal environmental factors, overloa-
ding, or unsuitable maintenance or cleaning, faults
caused by the use of spare parts, accessories or
replacements that are not original Werku
the product has been totally or partially disassem-
bled, modified or repaired by personnel other than
that of the Technical Assistance Service or mini-
mum and irrelevant irregularities for suitable use
or operation. Repairs and replacements will not
extend or renew the validity period of this warran-
6
English
is adhered to an Integrated
®
will not accept replacements if
®
distributor or the Werku
Technical As-
®
parts, if
®
Advertisement
Table of Contents
