LuxenHome WHF1054 Instruction Manual

Resin bunnies water pump outdoor fountain with led light

Advertisement

Resin Bunnies Water Pump Outdoor Fountain with LED Light
Product Name:
SKU #:
WHF1054
Thank you for purchasing this Luxen Home product. This product has been manufactured with the highest
standards of safety and quality.
PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLY.
Unpack all parts from Styrofoam and bubble wrap inside the carton to ensure there are no missing or damaged
parts. If any parts are missing or damaged, do not attempt to assemble or use the product.
CARTON CONTENTS:
Description
Fountain
Pump
Faucet Spout w/ tube
Handle
Bolt
Nut
Compatible Pumps for this fountain:
Pump Model No.
JR-250
JB333
YH300-70
Tools required for assembly: No tools required for assembly.

Assembly Instructions:

1. Unpack the contents of the box and check to make sure that all items are accounted for and in good
condition.
2. Select a flat, level surface for the assembly and final location of your fountain.
3. Insert handle and place bolt through the holes and screw in nut. Please fountain top onto fountain base.
4. From the opening in the back of the fountain, insert the LED connector into the pump connector, and twist
to tighten. Insert the water tube into the pump, and place the electric pump inside the fountain. Draw out
the pump cord from the back of the fountain.
5. Add clean water to the fountain. The water level should be approximately 30mm lower than the edge of the
basin.
6. Connect the power cable to outlet. If installed properly, water flow in the fountain will begin shortly.
7. Please do not use the electrical plug in wet weather conditions. Please note: On first use, there may be air in
the pump. It may take several minutes until all the air escapes.
8. To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing
after the initial setup of your fountain. It is highly recommended that this fountain be placed in an area
where it cannot be damaged.
Quantity
1
1
1
1
1
1
Contact: cs@winsomehouse.com
Please save this manual for future reference.
Instruction Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the WHF1054 and is the answer not in the manual?

Questions and answers

Summary of Contents for LuxenHome WHF1054

  • Page 1 Resin Bunnies Water Pump Outdoor Fountain with LED Light Product Name: SKU #: WHF1054 Thank you for purchasing this Luxen Home product. This product has been manufactured with the highest standards of safety and quality. PLEASE READ ALL INSTRUCTIONS BEFORE ASSEMBLY.
  • Page 2 Resin Bunnies Water Pump Outdoor Fountain with LED Light Product Name: SKU #: WHF1054 9. Do not leave your fountain running for extended periods of time when no one is present to observe the performance. 10. Check the area around your fountain on a regular basis to ensure that there is no leakage.
  • Page 3 Instruction Manual Please save this manual for future reference. Resin Bunnies Water Pump Outdoor Fountain with LED Light Product Name: SKU #: WHF1054 Pump Instructions: Special Warnings and Cautions: CAUTION: The pump has been evaluated for use with water only.
  • Page 4 Resin Bunnies Water Pump Outdoor Fountain with LED Light Product Name: SKU #: WHF1054 WARNINGS: 1. To reduce the risk of electric shock, connect only to a properly grounded, grounding type receptacle. 2. To reduce the risk of electric shock, use only on portable self-contained fountains no larger than 5 feet in any dimension.
  • Page 5 Resin Bunnies Water Pump Outdoor Fountain with LED Light Product Name: SKU #: WHF1054 TIPS AND TROUBLESHOOTING: 1. Ensure that the pump’s flow control switch is set to maximum (+) before operating. Once the flow is established, the pump can be adjusted downward to the desired level.

Table of Contents