Boss Audio Systems 616UAB User Manual

Overview of the Components
INT RPT RDM
POP ROCK CLASSIC FLAT
15
1. PWR(power On/Off), SRC (source) button,
2. VOL (volume) knob, (Push-To-Talk) button, SEL (select/menu) button
3. (tune/seek down, previous track, fast reverse) button
4. (tune/ seek up, next track, fast forward) button
5. BAND button, AMS(automatic store / preset station scan, automatic music
(answer call)
search) button,
6. LCD Display
7. (pause/play), (MUTE) button, Preset station 1 button
8. INT (intro), Preset station 2 button
9. RPT (repeat), Preset station 3 button
10. RDM (random), Preset station 4 button
11. -10(previous 10 tracks), F-(previous folder), Preset station 5 button
12. +10(next 10 tracks), F+(next folder), Preset station 6 button
13. IR remote sensor
14. USB Port
15. Hands-free Microphone
16. AUX IN (aux audio input) jack
17. Reset button
General Operation
Turn Unit on/off, Change the Source
• Press any button to turn on the unit. Press and hold the SRC/PWR button
to turn off the unit.
• Press the SRC/PWR button to select the different modes: Radio, USB(with
USB device inserted), AUX-IN(aux audio input) and BT(Bluetooth) modes.
Adjust the volume (VOL)
Rotate the VOL knob to increase or decrease the volume level.
Installation
Installation Procedures
First complete the electrical connections and then check for correctness of
connection.
Installation Opening
This unit can be installed in any dashboard which has an opening as shown
below.
Insert the mounting sleeve into the dashboard. Then bend the tabs
on the mounting sleeve with a screwdriver to achieve fastening of
the mounting sleeve.
Make sure that lock lever is flush with the mounting sleeve( not
projecting outward)
General Operation
16
Push-To-Talk
Press the
assistant capability via Bluetooth.
USB BT
Adjust Menu Options (SEL)
• Press and hold the SEL button (volume knob) to enter into setting menu,
then press the SEL button (volume knob) repeatedly to select setting items:
- Clock Display/Settings: Press and hold the SEL button (volume knob) to
diplay clock time.
Press and hold the SEL button (volume knob) again, the hours digits start
flashing on the display, Set hours by rotating the VOL knob.
17 14
Short press the SEL button (volume knob), the minute digits start flashing.
Set minutes by rotating the VOL knob.
(end call) button
- ILL MID/HI/LOW: This receiver is equipped with 3 brightness settings.
Rotate the volume knob to preset the illumination to middle, high or low.
- BASS/TREBLE:-7, -6, ~, 1, 0, +1,~, +6, +7
Note:
BASS and TREBLE settings are only enabled when EQ setting is turned OFF.
- BALANCE:L7, L6,~, L1, 0, R1,~,R6, R7
- FADER:R7, R6, ~, R1, 0, F1, ~ ,F6, F7
- Loudness: LOUD ON/OFF
- EQ(Equalizer) Setting: OFF, FLAT, CLASSIC, POP, ROCK, JAZZ
- Stereo/Mono: Switches between MONO and STEREO reception mode
for radio frequencies.
- DX/LOCAL: Enables or disables the local broadcast mode (LOCAL).
- CLOCK 12/24: Select between 12 hours and 24 hours display.
- AREA US/EU: This car radio is equipped the USA / Europe frequency.
Rotate the volume knob to switch between USA and Europe frequency.
The system will change the frequency setting in about 3 seconds.
• Rotate the VOL knob to change values.
Mute On/Off
During AUX mode, briefly press the
USB Port
Connect to a USB storage device for audio play, or charging of a mobile
phone.
Hands-free Microphone
To receive your voice when you calling by using this bluetooth handsfree
system.
Aux Audio Input Jack
Connect to the headphone jack on an external device (e.g. a mobile phone
or MP3 player) for audio play.
2.05 inches
7.20 inches
.
Mounting sleeve
Bracket key
Bracket key
Plastic trim out
icon button (VOL knob) to access to smartphone voice
button to toggle mute on or off.
Installation
Connect all wiring harness and slide the head unit into the
mounting
sleeve until it clicks into place.
Wiring Connections
F-L R-L
Radio Antenna
ANT F-R R-R
White: Front Left PRE-AMP Output
Red: Front Right PRE-AMP Output
Red: Rear Right PRE-AMP Output
White: Rear Left PRE-AMP Output
Front Left
White
Speaker
White/Black
Green
Rear Left
Speaker
Green/Black
- +12V DC Negative Ground.
!
- Only support speakers of 4 ohms or above.
- The maximum current of the Amp remote trigger is 200mA.
General Operation
Reset
Push the RESET button with a thin object with a pointed end to reset the unit.
This function may be used when the LCD does not display normally or
sound is distorted, or when any of controls are disabled.
Radio Operation
Switch Between USA area and Europe area Frequency
In radio mode, press and hold the SEL button (volume knob) to enter into
setting menu, then press the SEL button (volume knob) repeatedly to access
the state of the USA and Europe frequency, then rotate the volume knob to
switch between USA and europe frequency. The system will change the
frequency setting in about 3 seconds.
Change Bands
In radio mode, shortly press the BAND button to switch between the FM1
(F1), FM2(F2), FM3(F3) and AM1(A1), AM2(A2) bands.
To Store / Recall Preset Stations
The radio can be stored 6 preset stations for each band (FM1, FM2, FM3,
AM1 and AM2) for a total of 30 preset stations.
- To memorize a station:
Press and hold the desired preset buttons (1-6) to save a radio station.
- To recall a preset station:
Briefly press the respective station button (1-6) to recall the corresponding
preset station.
Manual Tuning
In the radio mode:
Press and hold the or button to enter the manual tuning mode.
In manual tuning mode, briefly press the or
or previous frequency step by step.
Seek Tuning
In radio mode, press the or button, the automatic search will start, it
will search upward or downward for the strong signal radio station within the
current band. The auto searching will stop until find a station.
Automatic Store Station / preset station scan
Press and hold the AMS button to store 18 FM stations and 12 AM stations
automatically.
10
ACC + (Red)
GND - (Black)
ANT + (Blue)
Power B+ (Yellow)
Gray
Front Right
Speaker
Gray/Black
Purple
Rear Right
Speaker
Purple/Black
button to search the next