ADC PG-FlexPlus AMU-912 Manual page 2

Table 2. Resistive Signatures
Test Failure Condition
RT Equipment RT detected, but no
Failure response from RT
Foreign Voltage TG or RG > 10 V
rms
on Drop TG or RG > 6 Vdc
All Tests OK No failures Detected
Ringer Test REN > 5.0 or < 0.2
Resistive Fault TG, RG, or TR > 150 K
on Drop
Receiver Off- Phone is off-hook
hook
Hazardous TG or RG > 50 V
rms
Potential on TG or RG > 135 Vdc
Drop
COT-RT RT not detected
Facility Failure
NOTE: The signatures for the AMU-912 L1 are biased to
-14 Vdc.
Network T1/HDSL Assignments
The T1/HDSL cable assignments are shown in Table 3. Note
that these circuits are terminated to the HyperEdge shelf
located below the PG-Flex chassis. The DS-1 interfaces
Plus
between these shelves are hard-wired and are not field
accessable.
Table 3. Network T1/HDSL Cable Assignments
Protector
Socket Tip Ring Description
White Blue Receive/Loop 1
1
HyperEdge 1/1
White Orange Receive/Loop 1
2
HyperEdge 1/2
White Green Receive/Loop 1
3
HyperEdge 1/3
White Brown Receive/Loop 1
4
HyperEdge 1/4
White Slate Receive/Loop 1
5
HyperEdge 1/5
Red Blue Receive/Loop 1
6
HyperEdge 1/6
Table 3. Network T1/HDSL Cable Assignments
TR TG,RG Protector
Socket
(k ) (k )
Ω Ω
7
17.8 90.9
8
27.8 90.9
38.3 90.9
9*
48.3 90.9
10*
Ω
58.0 90.9
11*
68.0 90.9
12*
78.5 90.0
13-25
26
>1,000 90.9
27
28
29
30
31
32
33
Conn
34*
35*
7
Tip Ring Description Conn
Red Orange Receive/Loop 1
HyperEdge 2./1
Red Green Receive/Loop 1
HyperEdge 2/2
Red Brown Receive/Loop 1
HyperEdge 2/3
Red Slate Receive/Loop 1
HyperEdge 2/4
Black Blue Receive/Loop 1
HyperEdge 2/5
Black Orange Receive/Loop 1
HyperEdge 2/6
Not Used
White Blue Transmit/Loop 2
HyperEdge 1/1
White Orange Transmit/Loop 2
HyperEdge 1/2
White Green Transmit/Loop 2
HyperEdge 1/3
White Brown Transmit/Loop 2
HyperEdge 1/4
White Slate Transmit/Loop 2
HyperEdge 1/5
Red Blue Transmit/Loop 2
HyperEdge 1/6
Red Orange Transmit/Loop 2
HyperEdge 2./1
Red Green Transmit/Loop 2
HyperEdge 2/2
Red Brown Transmit/Loop 2
HyperEdge 2/3
Red Slate Transmit/Loop 2
HyperEdge 2/4
Page 2 of 11
Table 3. Network T1/HDSL Cable Assignments
Protector
Socket Tip Ring
Black Blue
1 36*
Black Orange Transmit/Loop 2
0 37*
38-50
A
* Wired for future use
HDSL and Auxiliary Power Assignments
HDSL and auxiliary power pairs are hard-wired between the
PG-Flex shelf and the 'C' and 'D' 710 cables located in
Plus
the side splice chamber. Refer to Table 4 for FLL-814 cable
pair assignments and Table 5 for PLL-735 cable pair
assignments
Table 4. PG-Flex
Plus
Protector
Socket Tip Ring
White Blue
51
7
White Orange
52
1
White Green
53
0
White Brown
54
B
White Slate
55
Red Blue
56
Red Orange
57
Red Green
58
Red Brown
59
Red Slate
60
Black Blue
61
Description Conn
Transmit/Loop 2
HyperEdge 2/5
HyperEdge 2/6
Not Used
FLL-814 Cable Assignments
Description Connector
Loop 1
Power 1
Loop 1
HDSL1
Loop 1
Power 2
Loop 1
HDSL2
Loop 1
Power 3
Loop 1
HDSL 3
Loop 1 7
Power 4
Loop 1 1
HDSL 4
Loop 1 0
Power 5
Loop 1 C
HDSL 5
Loop 1
Power 6