Download Print this page
V-TAC VT-511S Installation Instruction

V-TAC VT-511S Installation Instruction

Led emergency light
Hide thumbs Also See for VT-511S:

Advertisement

Quick Links

WEEE Number: 80133970
INSTALLATION INSTRUCTION
LED EMERGENCY LIGHT
INTRODUCTION & WARRANTY
Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read
these instructions carefully before starting the installation and keep this manual handy for future
reference. If you have any another query, please contact our dealer or local vendor from whom
you have purchased the product. They are trained and ready to serve you at the best. The
warranty is valid for 3 years from the date of purchase. The warranty does not apply to damage
caused by incorrect installation or abnormal wear and tear. The company gives no warranty
against damage to any surface due to incorrect removal and installation of the product. This
product is warranted for manufacturing defects only.
!WARNING
• Please make sure to turn off the power before starting the installation.
• Installation should only be performed by a certified electrician.
• The light source of this luminaire is not replaceable, when the light source reaches its end of
life the whole luminaire should be replaced.
• If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in order to avoid
a hazard.
• Make sure the local voltage is the same with the product before plugging into the power
supply.
• The unit is designed with replacement battery. Battery replacement should only be performed
by a qualified electrician.
• Forbid to use in the rain or outdoors.
• Daily check – check that the status GREEN LED indicator is illuminated
• Do not install this product on damp or newly plastered surfaces.
• Ensure all electrical connections are secure and that there are no loose strands.
• For Indoor Use Only
3
*
WARRANTY
IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT: SUPPORT@V-TAC.EU
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST
DEALERS. V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B

Advertisement

loading

Summary of Contents for V-TAC VT-511S

  • Page 1 LED EMERGENCY LIGHT INTRODUCTION & WARRANTY Thank you for selecting and buying V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any another query, please contact our dealer or local vendor from whom you have purchased the product.
  • Page 2 • Above the 40°C (104°F) or under the 0°C render the product to be unsafe and will (32°F), the efficacy of lighting will decline. invalidate any Safety /Approvals. TECHNICAL DATA Model VT-511S Wa�s 3.8W Max Lumens 110LM Output Voltage 4.5W Ouput Power 1.2W...
  • Page 3: Installation Instructions

    INSTALLATION INSTRUCTIONS NOTE: Jumper cap switching position has the functions of AC/DC (Maintained) and DC (non-maintained). P1 is AC/DC position, P2 is DC position. (Refer to Picture F) THREE INSTALLATION METHODS WALL MOUNTING FLUSH MOUNTING CEILING MOUNTING I SURFACE MOUNTING (For wall only): 1.
  • Page 4 RECESSED INSTALLATION METHODS CONDUIT 1. REFLECTOR 3. RECESSED 2. BASE II RECESSED/FLUSH MOUNTING (For wall only): 1. Switch off the main power before installation 2. Push the conduit of the recessed box with a screwdriver 3. Open the emergency light with a help of a screwdriver (Figure A). 4.
  • Page 5: Operation

    OPERATION 1. If the AC power is normal, the green charging indicator will be ON which shows the lamp is charging. 2. If a power failure occurs, the emergency light senses the AC power failure and automatically switches to emergency mode. The emergency light will illuminate for a minimum of 4 hours.