Advertisement
Advertisement
Table of Contents
Related Manuals for Whirlpool PACF29COW
Summary of Contents for Whirlpool PACF29COW
- Page 4 SAFETY INSTRUCTIONS IMPORTANT TO BE READ AND OBSERVED • Download the complete instruction manual on docs.whirlpool.eu or call the phone number shown on the warranty booklet. • Before using the appliance, read these safety instructions. Keep them nearby for future reference.
- Page 5 SAFETY INSTRUCTIONS Never insert obstacle in the air outlet-risk of injury. Keep ventilation openings clear of any obstruction. INSTALLATION • The appliance must be handled and installed by two or more persons - risk of injury. Use protective gloves to unpack and install - risk of cuts. •...
- Page 7 SAFETY INSTRUCTIONS FOR SERVICING APPLIANCE WITH SPECIFIC REFRIGERANT • Download the complete manual for detailed installation, servicing, maintenance and reparing methods on docs.whirlpool.eu. • Do not use means to accelerate the defrosting process or to clean, other than those recommended by the manufacturer.
- Page 8 SAFETY INSTRUCTIONS 4. The storage of equipment / appliances should be in accordance with the manufacturer’s instructions. 5. Storage of packed (unsold) equipment Storage package protection should be constructed such that mechanical damage to the equipment inside the package will not cause a leak of the refrigerant charge. The maximum number of pieces of equipment permitted to be stored together will be by local regulations.
- Page 9 SAFETY INSTRUCTIONS 6-8 Checks to the refrigerating equipment Where electrical components are being changed, they shall be fit for the purpose and to the correct specification. At all times the manufacturer’s maintenance and service guidelines shall be followed. If in doubt consult the manufacturer’s technical department for assistance.
- Page 10 SAFETY INSTRUCTIONS Do not apply any permanent inductive or capacitance loads to the circuit without ensuring that this will not exceed the permissible voltage and current permitted for the equipment in use. Intrinsically safe components are the only types that can be worked on whilelive in the presence of a flammable atmosphere.
- Page 11 SAFETY INSTRUCTIONS used for this task. Purging shall be achieved by breaking to fill until the working pressure is achieved, then venting to atmosphere, and finally pulling down to a vacuum. This process shall be repeated until no refrigerant is within the system. When the final charge is used, the system shall be vented down to atmospheric pressure to enable work.
- Page 12 SAFETY INSTRUCTIONS on the equipment are closed off. k. Recovered refrigerant shall not be charged into another refrigerating system unless it has been cleaned and checked. 15. Labelling Equipment shall be labelled stating that it has been de-commissioned and emptied of refrigerant.
-
Page 14: Remote Controller
Remote controller Insert the batteries into RC Use RC to control the appliance 1. Insert a pin and gently press down on the battery • To operate the appliance by remote control, point the cover and push in the direction of the arrow to remote control at the receiving device on the indoor remove, as shown. -
Page 15: Maintenance
Maintenance Draining the Air Conditioner (Please connect the drain hose on heating mode,otherwise the unit will stop running after reachs warning level.) 1. Press ON/OFF to turn off the air conditioner. 2. Unplug air conditioner or disconnect power. 3. Move the appliance gently and stably to a draining location or outside to drain water. -
Page 16: Installation Instruction
Installation instruction Install Exhaust Hose and Adapter 1. Roll the air conditioner to selected location. see “Location Requirements” in page 4. 2. Preparing the exhaust hose assembly: Press the coupling and the window exhaust adapter into the flexible exhaust hose, Both the coupling and window exhaust adapter have integral clips that snap onto the hose. - Page 17 Installation instruction Tools and Parts Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. 1. Tools needed • Phillips screwdriver • • Cordless drill and 1/8” bit A. Flexible exhaust hose •...
-
Page 18: Troubleshooting
I8°C. Note: If the problems still have, turn off the appliance and disconnect from power supply, then contact the nearest Whirlpool Authorized Service Center. Do not attempt to move, repair, disassemble, or modify the appliance by yourself. -
Page 19: After Sales Service
IF AFTER THE ABOVE CHECKS THE FAULT STILL OCCURS, GET IN TOUCH WITH THE NEAREST AFTER-SALES SERVICE To receive assistance, call the number shown on the warranty booklet or follow the instructions on the website www.whirlpool.eu When contacting our Client After sales service, always specify: •...