H3C S5500-SI Series Operation Manual
Hide thumbs
Also See for S5500-SI Series:
- Operation manual (1217 pages) ,
- Configuration manual (130 pages) ,
- Installation manual (86 pages)
Table of Contents
Advertisement
Quick Links
Operation Manual - VLAN
H3C S5500-SI Series Ethernet Switches
Chapter 1 VLAN Configuration .................................................................................................... 1-1
1.1 VLAN Overview.................................................................................................................. 1-1
1.1.1 Introduction to VLAN ............................................................................................... 1-1
1.1.2 VLAN Classification................................................................................................. 1-2
1.2 Basic VLAN Configuration ................................................................................................. 1-2
1.3 Basic VLAN Interface Configuration .................................................................................. 1-2
1.4 Port-Based VLAN Configuration ........................................................................................ 1-3
1.4.1 Introduction of Port-Based VLAN ............................................................................ 1-3
1.4.2 Configuring an Access Port-Based VLAN............................................................... 1-5
1.4.3 Configuring a Trunk Port-Based VLAN ................................................................... 1-6
1.4.4 Configuring a Hybrid Port-Based VLAN.................................................................. 1-7
1.5 Displaying VLAN Configuration ......................................................................................... 1-8
1.6 VLAN Configuration Example ............................................................................................ 1-9
1.6.1 Network Requirements............................................................................................ 1-9
1.6.2 Network Diagram..................................................................................................... 1-9
1.6.3 Configuration Procedure ......................................................................................... 1-9
Chapter 2 Voice VLAN Configuration.......................................................................................... 2-1
2.1 Voice VLAN Overview ....................................................................................................... 2-1
2.1.1 Automatic and Manual Voice VLAN Modes ............................................................ 2-1
2.1.2 Security and Ordinary Voice VLAN Modes ............................................................. 2-4
2.2 Voice VLAN Configuration ................................................................................................. 2-4
2.2.1 Configuration Prerequisites..................................................................................... 2-4
2.2.2 Configuring Voice VLAN in Automatic Mode .......................................................... 2-5
2.2.3 Configuring Voice VLAN in Manual Mode............................................................... 2-6
2.3 Displaying Voice VLAN...................................................................................................... 2-7
2.4 Voice VLAN Configuration Example .................................................................................. 2-7
2.4.1 Voice VLAN Configuration Example (Automatic Mode).......................................... 2-7
2.4.2 Voice VLAN Configuration Example (Manual Mode) .............................................. 2-9
Chapter 3 GVRP Configuration .................................................................................................... 3-1
3.1 Introduction to GARP......................................................................................................... 3-1
3.1.1 Introduction to GARP .............................................................................................. 3-1
3.1.2 Introduction to GVRP .............................................................................................. 3-3
3.1.3 Protocols and Standards......................................................................................... 3-4
3.2 Configuring GVRP ............................................................................................................. 3-4
3.2.1 Configuring GVRP................................................................................................... 3-4
3.2.2 Setting GARP Timer................................................................................................ 3-5
3.3 Displaying and Maintaining GARP/GVRP ......................................................................... 3-6
Table of Contents
i
Table of Contents
Advertisement
Table of Contents
Related Manuals for H3C S5500-SI Series
Summary of Contents for H3C S5500-SI Series
-
Page 1: Table Of Contents
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Table of Contents Table of Contents Chapter 1 VLAN Configuration ....................1-1 1.1 VLAN Overview........................1-1 1.1.1 Introduction to VLAN ....................1-1 1.1.2 VLAN Classification....................1-2 1.2 Basic VLAN Configuration ....................1-2 1.3 Basic VLAN Interface Configuration .................. - Page 2 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Table of Contents 3.4 GVRP Configuration Example ................... 3-7 3.4.1 Example 1 ....................... 3-7 3.4.2 Example 2 ....................... 3-8 3.4.3 Example 3 ....................... 3-9...
-
Page 3: Chapter 1 Vlan Configuration
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 1 VLAN Configuration Chapter 1 VLAN Configuration 1.1 VLAN Overview 1.1.1 Introduction to VLAN The virtual local area network (VLAN) technology is developed for switches to control broadcast operations in LANs. -
Page 4: Vlan Classification
MAC-based VLAN Protocol-based VLAN IP sub network-based VLAN Policy-based VLAN Other VLAN H3C S5500-SI Series Ethernet Switch supports the port-based VLAN. This chapter will focus on the port-based VLAN. 1.2 Basic VLAN Configuration Table 1-1 Basic VLAN configuration To do…... -
Page 5: Port-Based Vlan Configuration
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 1 VLAN Configuration Table 1-2 Configure a VLAN interface To do… Use the command… Remarks Enter system view system-view — Required If the specified VLAN Create a VLAN interface interface vlan-interface... - Page 6 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 1 VLAN Configuration I. Link Type of an Ethernet Port Depending on how a port processes VLAN tags when it forwards packets, the link type of the port can be one of the following three types: Access.
-
Page 7: Configuring An Access Port-Based Vlan
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 1 VLAN Configuration Table 1-3 Incoming and outgoing packets Incoming packet If no tag is Port type Outgoing packet If a tag is carried in carried in the the packet... -
Page 8: Configuring A Trunk Port-Based Vlan
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 1 VLAN Configuration Table 1-4 Configure an access port-based VLAN (in VLAN view) To do… Use the command… Remarks Enter system view system-view — Required If the specified VLAN does... -
Page 9: Configuring A Hybrid Port-Based Vlan
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 1 VLAN Configuration Table 1-6 Configure a trunk port-based VLAN To do… Use the command… Remarks Enter system view system-view — Enter Use either command interface interface-type Ethernet Configured in Ethernet... -
Page 10: Displaying Vlan Configuration
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 1 VLAN Configuration Table 1-7 Configure a hybrid port-based VLAN To do… Use the command… Remarks Enter system view system-view — Enter Use either command interface interface-type Ethernet Enter Configured in Ethernet port... -
Page 11: Vlan Configuration Example
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 1 VLAN Configuration Table 1-8 Display the information about specified VLANs To do… Use the command… Remarks display vlan vlan-id1 Display the information vlan-id2 ] | all | static | dynamic |... - Page 12 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 1 VLAN Configuration # Configure GigabitEthernet1/0/1 as a trunk port, and configure its default VLAN ID as VLAN 100. [Sysname-GigabitEthernet1/0/1] port link-type trunk [Sysname-GigabitEthernet1/0/1] port trunk pvid vlan 100 # Configure GigabitEthernet1/0/1 to permit the packets from VLAN 2, VLAN 6 through 50, and VLAN 100 to pass.
-
Page 13: Chapter 2 Voice Vlan Configuration
(QoS)-related configuration for voice data, ensuring the transmission priority of voice data stream and voice quality. S5500-SI series Ethernet switches determine whether a received packet is a voice packet by checking its source MAC address. If the source MAC addresses of packets comply with the organizationally unique identifier (OUI) addresses configured by the system, the packets are determined as voice packets and transmitted in voice VLAN. - Page 14 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 2 Voice VLAN Configuration In automatic mode, the system identifies the source MAC address contained in the untagged packet sent when the IP phone is powered on and matches it against the OUI addresses.
- Page 15 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 2 Voice VLAN Configuration Port voice VLAN Voice Port type Supported or not mode stream type Access Not supported Supported Make sure the default VLAN of the port exists Trunk and is not a voice VLAN.
-
Page 16: Security And Ordinary Voice Vlan Modes
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 2 Voice VLAN Configuration Caution: If the voice stream transmitted by your IP phone is with VLAN tag and the port which the IP phone is attached to is enabled with 802.1x authentication and 802.1x guest VLAN, assign different VLAN IDs for the voice VLAN, the default VLAN of the port, and the 802.1x guest VLAN to ensure the two functions to operate properly. -
Page 17: Configuring Voice Vlan In Automatic Mode
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 2 Voice VLAN Configuration VLAN 1 is the default VLAN and do not need to be created. But VLAN 1 does not support the voice VLAN function. 2.2.2 Configuring Voice VLAN in Automatic Mode Table 2-3 Configure voice VLAN in automatic mode To do…... -
Page 18: Configuring Voice Vlan In Manual Mode
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 2 Voice VLAN Configuration 2.2.3 Configuring Voice VLAN in Manual Mode Table 2-4 Configure voice VLAN in manual mode To do… Use the command… Remarks Enter system view system-view —... -
Page 19: Displaying Voice Vlan
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 2 Voice VLAN Configuration Note: Note the following when configuring voice VLAN in manual and automatic modes. You can enable the voice VLAN function for only one static VLAN on a switch. And a dynamic VLAN cannot be configured as a voice VLAN. - Page 20 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 2 Voice VLAN Configuration II. Network diagram VLAN 2 VLAN 2 GigabitEthernet GigabitEthernet 1/0/1 1/0/1 Tel.1 010-1001 Tel.1 010-1001 OUI:0011-2200-0000 OUI:0011-2200-0000 Mask:ffff-ff00-0000 Mask:ffff-ff00-0000 Figure 2-1 Network diagram for configuration of voice VLAN in automatic mode III.
-
Page 21: Voice Vlan Configuration Example (Manual Mode)
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 2 Voice VLAN Configuration 2.4.2 Voice VLAN Configuration Example (Manual Mode) I. Network requirements Create VLAN 2 and configure it as a voice VLAN. The voice stream transmitted by the IP phone is untagged, and the port which the IP phone is attached to is a Hybrid port GigabitEthernet1/0/1. - Page 22 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 2 Voice VLAN Configuration [Sysname-GigabitEthernet1/0/1] port link-type hybrid # Configure VLAN 2 as the default VLAN of port GigabitEthernet1/0/1, and allow packets of VLAN 2 to pass through the port.
-
Page 23: Chapter 3 Gvrp Configuration
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 3 GVRP Configuration Chapter 3 GVRP Configuration 3.1 Introduction to GARP 3.1.1 Introduction to GARP The generic attribute registration protocol (GARP), provides a mechanism that allows participants in a GARP application to distribute, propagate, and register with other participants in a bridged LAN the attributes specific to the GARP application, such as the VLAN or multicast address attribute. - Page 24 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 3 GVRP Configuration Leaveall timer –– Starts when a GARP application entity starts. When this timer expires, the entity sends a LeaveAll message so that other entities can re-register its attribute information. Then, a leaveall timer starts again.
-
Page 25: Introduction To Gvrp
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 3 GVRP Configuration The following table describes the GARP message fields. Table 3-1 Description on the GARP message fields Field Description Value Protocol ID Protocol identifier for GARP One or multiple messages, each... -
Page 26: Protocols And Standards
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 3 GVRP Configuration Fixed –– Disables the port to dynamically register/deregister VLANs or propagate dynamic VLAN information, but allows the port to propagate static VLAN information. A trunk port with fixed registration type thus allows only manually configured VLANs to pass through even though it is configured to carry all VLANs. -
Page 27: Setting Garp Timer
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 3 GVRP Configuration To do… Use the command… Remarks Optional gvrp registration Configure GVRP registration { fixed | forbidden | default mode on the port normal } normal Note: BPDU TUNNEL is not compatible with GVRP. The two cannot be applied simultaneously on a port. -
Page 28: Displaying And Maintaining Garp/Gvrp
Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 3 GVRP Configuration Table 3-4 Dependencies of GARP timers Timer Lower limit Upper limit Not greater than half of the join timer setting Hold 10 centiseconds You can change this value by changing the value of the join timer. - Page 29 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 3 GVRP Configuration 3.4 GVRP Configuration Example 3.4.1 Example 1 I. Network requirements Configure GVRP on devices and specify the port registration mode as normal to realize dynamic VLAN information registration and update among devices.
- Page 30 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 3 GVRP Configuration # Enable GVRP on GigabitEthernet 1/0/2. [Sysname-GigabitEthernet1/0/2] gvrp # Configure static VLAN3. [Sysname-GigabitEthernet1/0/2] quit [Sysname] vlan 3 [Sysname-vlan3] Display configuration results # Display dynamic VLAN on Switch A.
- Page 31 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 3 GVRP Configuration [Sysname-GigabitEthernet1/0/1] gvrp # Configure the GVRP registration mode as fixed. [Sysname-GigabitEthernet1/0/1] gvrp registration fixed # Create static VLAN 2. [Sysname-GigabitEthernet1/0/1] quit [Sysname] vlan 2 [Sysname-vlan2] Configure Switch B # Enable GVRP globally.
- Page 32 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 3 GVRP Configuration II. Network diagram GigabitEthernet GigabitEthernet 1/0/1 1/0/1 GigabitEthernet GigabitEthernet 1/0/2 1/0/2 Switch B Switch B Switch B Switch B Switch B Switch B Switch B Switch B...
- Page 33 Operation Manual – VLAN H3C S5500-SI Series Ethernet Switches Chapter 3 GVRP Configuration [Sysname] vlan 3 [Sysname-vlan3] Display the configuration # Display dynamic VLAN information on Switch A [Sysname-vlan2] display vlan dynamic No dynamic vlans exist! # Display dynamic VLAN information on Switch B.