Battery Backup - Intermatic ET70415CR User Manual

owner wants to offset actual sunrise time by having lights
switch off 30 min. late, press CLEAR, CLEAR, CLEAR
(deletes automatic center of zone calculation; display
now shows --:--) and 8, 0, 3, OK (selects new offset
sunrise time). The time switch now displays the
calculated center of time zone sunset time of -5:13 P.M.
Since the building owner wants to offset actual sunset
time, press CLEAR, CLEAR, CLEAR (deletes automatic
center of zone calculation; display now shows --:--);
4, 4, 3, OK (selects new offset sunset time);1, OK
(selects first Holiday schedule Ref. # for 1997); 7, 0, 4,
OK, OK (pressing OK twice selects same start and stop
date); 2, OK (selects second Holiday schedule Ref. #);
1, 2, 2, 2, OK (start date); 1, 2, 3, 1 OK (stop date);
3, OK (selects first Holiday schedule Ref. # for 1998);
1, 0, 1, OK (start date) and 1, 0, 5, OK (stop date).
SET UP is now complete.
Press PROG (to enter PROGRAM mode and exit SET UP)
Assume • Programming for two loads: #1 indoor lighting, #2
buzzer
• Load 1 switches On 7:50 A.M. to 4:40 P.M.
Monday thru Friday and 7:50 A.M. to 12:00 P.M. noon
Sat. only.
• Load 2 operates the signal twice daily for 15 sec. at
8:00 A.M. and 4:30 P.M. Monday thru Friday only.
Set Load slide switches to Enable Load 1 and Disable 2
Press WKdy/8, OK (selects weekdays only); 7, 5, 0, AM, OK
(load On time); 4, 4, 0, PM, OK (load Off time)
Set Load slide switches to Disable Load 1 and Enable 2
Press 8, 0, 0, AM, PULSE, 1, 5, OK (selects 15 sec. load On
at 8:00 A.M.); 4, 3, 0, PM, PULSE, 1, 5, OK (selects 15
sec. load On at 4:30 P.M.)
Press PROG to select a new day or day group to program.
Set Load slide switches to Enable Load 1and Disable 2
Press SAT/7, OK (selects Saturday only); 7, 5, 0, AM, OK
(load On time); 1, 2, 0, 0, PM, OK (load Off time)
18
Scheduled PROGRAM is now complete.
Assume A 30 min. INTERVAL override duration is desired for
Load 1.
Set Load slide switches to Enable Load 1 and Disable 2
Press PROG (completes programming for Saturday data)
INTVL, 3, 0, OK (sets user selectable interval duration
to 30 minutes)
(Note a day or day group is not selected since Interval
override is selected on demand by the building occupants.)
Interval override duration selection is now complete.
The interval override will not begin until called for by
the user via the front panel pushbuttons, or by a switch
connected to the remote override connector.
To complete programming, download all data into non-volatile
memory by sliding the SET/RUN switch to RUN. Note SAVE is
displayed momentarily and the current day of week and time
appear in the display.
NOTE: If you need more programming assistance, request form
#158ET9311, Programming Examples, which contains step-by-
step instructions for several complex programs.

BATTERY BACKUP

All programmed data is protected by non-volatile memory and can
only be changed or deleted by reprogramming, regardless of power
outage durations. A factory installed 8-year lithium battery backup
maintains accurate time and calendar information. See Special
Instructions for replacement.
Next Generation
19